Study guide
3.4 Sacrificial Anode Materials: Mg, Zn, & Al Alloys
AMPP CP1 Cathodic Protection Tester Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & CP Exam Overview
About the AMPP CP1 Tester Exam & Certification Path How to Study for CP1 & Navigate This Guide Corrosion Science & Industry Terminology Glossary Field Mathematics & Ohm's Law Fundamentals AMPP Ethics for the Corrosion Professional
2 Chapter 2: Fundamentals of Electrochemistry & Corrosion Cells
2.1 The Corrosion Cell: Anode, Cathode, Electrolyte & Metallic Path 2.2 Anodic & Cathodic Reactions on Carbon Steel 2.3 Galvanic Series & Electromotive Force (EMF) Series 2.4 Forms of Corrosion: Uniform, Galvanic, Pitting & Crevice 2.5 Factors Affecting Corrosion Rates: Oxygen, pH, Temperature & Flow
3 Chapter 3: Principles of Cathodic Protection
3.1 Cathodic Protection Theory & Mixed-Potential Diagrams 3.2 Galvanic (Sacrificial Anode) CP Systems 3.3 Impressed Current Cathodic Protection (ICCP) Systems 3.4 Sacrificial Anode Materials: Mg, Zn, & Al Alloys 3.5 ICCP Anode Materials: MMO, Graphite, HSCI, & Platinum
4 Chapter 4: Electrical Circuit Analysis for CP
4.1 Ohm's Law Applications in CP Circuits 4.2 Series & Parallel Resistance in CP Groundbeds & Piping 4.3 Kirchhoff's Voltage & Current Laws in Network Piping 4.4 Shunts: Types, Ratings & Current Calculations 4.5 Rectifier Operation & Transformer Tap Adjustments
5 Chapter 5: Reference Electrodes & Half-Cell Potentials
5.1 Copper/Copper Sulfate (CSE) Reference Electrode Construction & Maintenance 5.2 Silver/Silver Chloride (Ag/AgCl) & Zinc Reference Electrodes 5.3 Converting Potentials Between Reference Electrodes 5.4 Reference Electrode Care, Temperature Correction & Contamination Checks 5.5 High-Impedance Voltmeters & Contact Resistance Errors
6 Chapter 6: Field Measurement & Potential Criteria
6.1 Structure-to-Electrolyte Potential Measurement Procedures 6.2 The -850 mV CSE Polarized Criterion (NACE SP0169) 6.3 The 100 mV Polarization Decay Criterion 6.4 Understanding IR Drop & The Instant-Off Interruption Technique 6.5 Native, On, Polarized, & Off Potentials Comparison
7 Chapter 7: Advanced Field Survey Techniques
Soil Resistivity Testing: Wenner 4-Pin Method (ASTM G57) Soil Pin Spacing, Layering & Corrosivity Classification Close Interval Potential Surveys (CIPS) Direct Current Voltage Gradient (DCVG) Coating Fault Surveys Cathodic Protection Coupons for IR-Free Potential Measurements
8 Chapter 8: Test Stations, Isolation & Stray Current
8.1 Test Station Types, Lead Wires & Commissioning Inspection 8.2 Electrical Isolation Joints & Dielectric Flange Testing 8.3 Casing Isolation & Shorted Casing Testing 8.4 DC Stray Current Interference: Detection & Mitigation 8.5 AC Stray Current Interference & Induction Hazards (NACE SP0177)
9 Chapter 9: Industry Standards & Field Documentation
9.1 NACE SP0169: External Corrosion Control Overview 9.2 NACE TM0497: Measurement Techniques Standard 9.3 Regulatory Compliance: PHMSA, DOT, & EPA Requirements 9.4 CP Data Collection, Logging & Quality Assurance 9.5 Rectifier Maintenance & Routine Inspection Logs 9.6 Anode Groundbed Testing & Resistance Measurements
10 Chapter 10: Electrical & Operational Safety for CP Personnel
10.1 Rectifier Electrical Safety, Lockout/Tagout (LOTO) & NFPA 70E 10.2 AC Induction Hazards Near High-Voltage Power Lines 10.3 Hazardous Atmospheres & Confined Space Safety at Test Vaults 10.4 Personal Protective Equipment (PPE) & Arc Flash Protection 10.5 Excavation, Trenching & Underground Utility Location (811) 10.6 Stop-Work Authority & Emergency Response Procedures
3.4 Sacrificial Anode Materials: Mg, Zn, & Al Alloys
Key Takeaways Explain This Topic AI
Magnesium anodes provide the highest driving voltage and are primarily used in soil.
Zinc anodes have a lower driving voltage, making them suitable for low-resistivity soils and seawater, and they are self-regulating.
Aluminum anodes are lightweight with high capacity, used almost exclusively in marine (seawater/brackish) environments.
Anode efficiency determines how much of the material's theoretical energy is actually converted into useful CP current.
The choice of anode material is dictated by the environment's resistivity and the required driving voltage.
Last updated: July 2026
Sacrificial Anode Materials: Mg, Zn, & Al Alloys
The success of a galvanic cathodic protection system hinges entirely on selecting the correct anode material for the specific environment. Not all metals make good sacrificial anodes. A suitable anode material must have a sufficiently negative open-circuit potential to provide a driving voltage, a high electrical capacity (amp-hours per pound), a high and predictable efficiency, and a tendency to corrode uniformly without passivating.
The corrosion industry relies almost exclusively on three metals and their highly specific alloys: Magnesium, Zinc, and Aluminum.
Magnesium (Mg) Anodes
Magnesium is the workhorse for underground (soil) galvanic CP systems. It is highly active in the galvanic series, providing the highest driving voltage of the common anode materials. This makes it the only practical choice for soils with moderate to high resistivity.
Types of Magnesium Anodes
There are two primary alloys of magnesium used in CP, distinguished by their purity and resulting potential:
Standard Potential (H-1 Alloy or AZ63):
Composition: Contains specific amounts of Aluminum (approx. 6%) and Zinc (approx. 3%).
Potential: Typically -1.45 V to -1.55 V (vs. Copper-Copper Sulfate Electrode, CSE).
Driving Voltage (to a -0.85V polarized structure): ~0.65 V.
Application: Used in low to moderate resistivity soils (typically less than 2,000 ohm-cm). They offer slightly higher efficiency than high-potential anodes but less driving voltage.
High Potential (High Purity) Alloy:
Composition: Extremely pure magnesium with trace amounts of manganese to improve efficiency.
Potential: Typically -1.70 V to -1.75 V (vs. CSE).
Driving Voltage (to a -0.85V polarized structure): ~0.90 V.
Application: The go-to choice for higher resistivity soils (up to roughly 10,000 ohm-cm). The extra driving voltage is necessary to push current through the resistive earth. They are the most common anode used on pipelines today.
Properties of Magnesium
Theoretical Capacity: Very high, approximately 1000 Amp-hours per pound (Ah/lb).
Efficiency: Relatively low. Magnesium is so reactive that it undergoes significant "self-corrosion" (local cell action on its own surface that doesn't contribute protective current to the pipeline). Typical efficiency in soil is around 50% . This means only about 500 Ah/lb of useful current is actually realized.
Environment: Used almost exclusively in soil and sometimes fresh water. Seldom used in seawater because they consume far too rapidly and can over-protect structures, leading to coating damage.
Zinc (Zn) Anodes
Zinc has been used for cathodic protection longer than any other metal. It is less active than magnesium, providing a lower driving voltage, but it is highly efficient and reliable in the right environments.
Properties of Zinc
Potential: Extremely stable at approximately -1.10 V (vs. CSE).
Driving Voltage (to a -0.85V polarized structure): ~0.25 V.
Theoretical Capacity: Lower than magnesium, approximately 372 Ah/lb.
Efficiency: Very high, typically 90% to 95% . Zinc suffers from very little self-corrosion. Therefore, its practical capacity is around 335 Ah/lb.
Applications of Zinc
Because of its low driving voltage (only 0.25 V), zinc can only push current through very low-resistance circuits.
Low Resistivity Soils: Zinc is excellent in soils with resistivity below 1,000 ohm-cm (like coastal marshes or saline soils).
Marine Environments: Zinc was historically the primary anode for seawater applications (hulls of ships, offshore structures) because seawater has very low resistivity (often < 30 ohm-cm). However, aluminum has largely replaced zinc in seawater due to weight and capacity advantages.
AC Mitigation and Grounding: Zinc is uniquely suited for grounding structures to mitigate induced AC voltage or fault currents. It provides a safe grounding path while simultaneously offering some cathodic protection, unlike copper grounds which would cause severe galvanic corrosion to a steel pipeline.
Temperature Limitation: Zinc anodes should not be used in environments exceeding 140°F (60°C). Above this temperature, a phenomenon called "polarity reversal" can occur, where the zinc actually becomes cathodic to the steel, causing the steel to corrode rapidly to protect the zinc.
Aluminum (Al) Anodes
Pure aluminum passivates easily, forming a tight oxide film that stops current output. However, by alloying aluminum with small amounts of metals like indium, zinc, or mercury, it remains active. Aluminum alloys are now the dominant sacrificial anode for marine environments.
Properties of Aluminum Alloys
Potential: Similar to zinc, typically -1.10 V to -1.15 V (vs. Silver-Silver Chloride electrode, Ag/AgCl, which is standard for seawater).
Driving Voltage: Similar to zinc, relatively low.
Theoretical Capacity: Extremely high, approximately 1350 Ah/lb.
Efficiency: High, typically around 85% to 90% in seawater. This yields a massive practical capacity of over 1150 Ah/lb.
Applications of Aluminum
Seawater Exclusivity: Aluminum anodes are used almost exclusively in seawater and brackish water (offshore platforms, ship hulls, submerged pipelines).
Why not soil? Aluminum anodes rely on the abundant chloride ions present in seawater to prevent that tight oxide film from forming. If placed in typical soils, they will quickly passivate, shut down, and stop providing current.
Weight Advantage: Aluminum is significantly less dense than zinc. An aluminum anode of the same physical size as a zinc anode will weigh much less but provide far more total amp-hours of protection. This makes aluminum highly cost-effective for large offshore structures where the weight of the CP system is a structural consideration.
Material Selection Summary
- Environment Typical Resistivity Preferred Anode Material
- Typical Soils 2,000 - 10,000 ohm-cm Magnesium (High Potential)
- Saline / Marshy Soils < 1,000 ohm-cm Magnesium (Standard) or Zinc
- Seawater ~30 ohm-cm Aluminum Alloys (or Zinc)
- High Temp (>140°F) Any Avoid Zinc (Risk of polarity reversal)
Understanding these material properties allows the CP tester to identify when the wrong material might have been installed, explaining system failures.
EPG Practical Galvanic Series (vs CSE)
The AMPP CP1 Exam Preparation Guide lists these approximate open-circuit potentials versus saturated Cu/CuSO₄ for exam reference:
- Material Potential vs CSE (V)
- High-Potential Magnesium −1.75
- Magnesium Alloy −1.60
- Zinc −1.10
- Aluminum Alloy −1.05
- Clean Carbon Steel −0.50 to −0.80
Use −1.60 V CSE for standard magnesium alloy anodes and −1.75 V CSE for high-potential magnesium—not a −1.45 to −1.55 V band.