Study guide
6.4 Cased vs Uncased, Bore Specs & Voids
API 1169 Pipeline Construction Inspector Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Overview
1.1 Current Exam Facts & Logistics 1.2 Eligibility Pathways & Application 1.3 Publications Effectivity Sheet & On-Screen References 1.4 Scaled Scoring, Passing Score & Results 1.5 Study Strategy, Recertification & Web Quiz
2 Chapter 2: Inspector Roles & Quality Management
2.1 Inspector Roles, Responsibilities & Authority 2.2 Quality Assurance Records & Documentation 2.3 Hold Points, Witness Points & Inspection Test Plans 2.4 API Spec Q1 Quality Management System
3 Chapter 3: Safety, Environmental & Qualifications
3.1 Safety Roles, Stop-Work & Site Safety 3.2 Environmental Controls, Permits & SWPPP/BMPs 3.3 Training, OQ & Personnel Qualification
4 Chapter 4: Front-End Construction
4.1 Survey, Staking & Alignment Sheets 4.2 Line Locating & One-Call (CGA) Coordination 4.3 ROW Clearing, Grading & Topsoil Segregation 4.4 Permits, Encroachments & Landowner Requirements
5 Chapter 5: Stringing, Bending & Welding
5.1 Stringing, Material Identification & Handling 5.2 Bending: Ovality, Wrinkles & Equipment 5.3 Welding Procedures, Qualification & API 1104 5.4 Consumable Control, Weld Docs & Repairs
6 Chapter 6: NDE, Trenching & Crossings
6.1 NDE Methods, Acceptance Criteria & Documentation 6.2 Trenching & Excavation Safety 6.3 Crossings, HDD & Drills 6.4 Cased vs Uncased, Bore Specs & Voids
7 Chapter 7: Coating, Padding, Lowering-In & Tie-Ins
7.1 Coating Procedures, Qualification & Field Joints 7.2 Padding & Lowering-In 7.3 Tie-Ins: Alignment, OQ & Material ID 7.4 Coating Repair, Holiday Inspection & Testing
8 Chapter 8: Back-End — CP, As-Builts, Backfill & Restoration
8.1 Cathodic Protection Installation & Test Leads 8.2 As-Built Survey, Redline Drawings & Weld Maps 8.3 Backfill & Buoyancy Control 8.4 ROW Cleanup & Restoration
9 Chapter 9: Hydrostatic Testing & Pigging
9.1 Hydrostatic & Pneumatic Testing (API RP 1110 / INGAA CS-S-9) 9.2 Gauge Plates, Deformation & Test Failures 9.3 Pigging, Cleaning & Drying
10 Chapter 10: Post-Construction & Turnover
10.1 Line-List Closeout 10.2 Final Completion Assessment & Punch-Out 10.3 Turnover to Operations & Documentation Packages
6.4 Cased vs Uncased, Bore Specs & Voids
Key Takeaways Explain This Topic AI
A cased crossing carries the carrier pipe inside an outer casing with insulators, end seals, and (for gas) vent pipes; an uncased crossing installs the pipe directly with a CP-compatible design
The crossing permit dictates cased vs uncased; railroads and some road authorities still require casing, while modern coatings and HDD have made uncased crossings common where permitted
Casing insulators center the carrier and electrically isolate it from the casing; a failed insulator shorts cathodic protection and risks corrosion of the carrier
Vent pipes on gas cased crossings must be installed, extended above grade, and vent-tested open; end seals keep water and soil out of the annulus
Bore voids and annular spaces may require grouting to prevent surface settlement; the inspector verifies grout placement and that vents are not blocked
Last updated: August 2026
6.4 Cased vs Uncased, Bore Specs & Voids
Quick Answer: A cased crossing carries the carrier pipe inside a larger outer casing (with insulators, end seals, and vent pipes for gas lines) at roads and railroads where the permit or code requires it; an uncased (direct) crossing installs the pipe directly in the bore with a cathodic-protection-compatible design. The API 1169 inspector verifies casing installation, insulators, end seals, vents, and the casing vent test, and checks for bore voids and grouting and the condition of the pipe inside the casing.
Cased vs Uncased: When Each Is Used
- Feature Cased Crossing Uncased (Direct) Crossing
- Structure Carrier pipe inside an outer casing Pipe installed directly in the bore
Typical location Roads and railroads where required by permit or code Modern HDD crossings; where a CP-compatible design and permit allow
Corrosion protection Casing isolates the carrier from external loads; requires insulators to prevent shorting CP Direct CP on the carrier pipe; no casing-to-carrier short risk
- Vents Vent pipes required for gas lines to detect leaks No casing vents needed
- End seals End seals keep water and soil out of the annulus N/A — no annulus
- Insulators/spacers Insulators center the carrier and electrically isolate it from the casing N/A
Inspector focus Casing installation, insulators, end seals, vents, vent test Pipe coating, cover, CP continuity, bore tolerance
Why Casings Are (Sometimes) Required
Casings were historically required at road and railroad crossings to let the carrier pipe be removed or replaced without disturbing the surface, and to take external loads off the carrier. Some railroad and state permits still require casing; others now allow uncased installations with concrete coating, deeper cover, or HDD. The crossing agreement/permit dictates which is used, and the inspector verifies the as-built crossing matches what the permit authorizes.
Why Uncased Is Now Common
Modern coatings and cathodic-protection systems, plus HDD, have made uncased crossings common — there is no casing-to-carrier short to defeat CP, and no annulus to fill with water. However, uncased crossings require a CP-compatible design and the permit must allow it. The inspector verifies CP test leads are installed and that continuity is confirmed.
- Casing Components the Inspector Verifies
- Casing Insulators/Spacers
Insulators (also called casing spacers) center the carrier pipe inside the casing and electrically isolate the carrier from the casing.
If an insulator fails, the carrier shorts to the casing and CP current is shielded — the carrier can corrode undetected.
The inspector verifies: insulator type and spacing per spec, insulators installed and undamaged, and the carrier is centered.
End Seals
End seals close the annulus between carrier and casing to keep water, soil, and debris out.
A failed end seal lets water into the annulus, which can cause external corrosion of the carrier and freeze damage in cold climates.
The inspector verifies end seals are installed per spec and sealed at both ends.
Vent Pipes (Gas Lines)
For gas pipelines in cased crossings, vent pipes are required:
Vents extend from the annulus to above grade so any gas leak into the casing is detected and vented safely.
Typically one or two vents per casing, per code and permit.
The casing vent test — the inspector verifies the vent is open (not plugged) and that a test (commonly a low-pressure air test or vacuum) confirms the annulus-to-vent path is clear.
Pipe Condition in Casing
Before the carrier is pushed into the casing:
Coating inspected — the carrier coating must be holiday-free; any damage is repaired before insertion.
Pull-through / test holes — the inspector may witness a pull-through test to confirm the carrier does not bind or damage coating.
After insertion, the carrier is centered and isolated — insulators not displaced, no short to the casing.
Bore Voids and Grouting
At cased crossings, the annular space between the casing and the surrounding soil (or between carrier and casing, where specified) may need to be grouted :
Grouting fills voids to prevent settlement of the surface above, to lock the casing in place, or to seal the annulus.
Bore voids — if the bore is over-sized or soil collapses, voids outside the casing can cause surface settlement; the inspector verifies voids are grouted per spec.
Grout type — cement-bentonite or flowable fill per the crossing spec.
The inspector verifies grout volume and placement, and that vent and drain paths are not blocked by grout.
Inspector Verification Checklist for Cased Crossings
Casing material and size per spec — diameter, wall thickness, grade, and length.
Casing installation — bore or open-cut per permit; casing centered in the bore.
Insulators/spacers — type and spacing per spec, installed and undamaged; carrier centered and isolated.
End seals — installed and sealed at both ends.
Vent pipes (gas) — installed, extended above grade, and vent-tested open.
Carrier pipe coating — holiday-free before and after insertion.
Grouting and voids — annulus or bore voids grouted per spec; vents not blocked.
CP isolation — carrier-to-casing isolation verified (no short).
Uncased Crossing Inspector Checks
Coating — concrete-weight or abrasion-resistant coating per spec; holiday-free.
Cover — depth of cover under the feature per permit.
CP continuity — no casing short; test leads installed per the CP design and continuity confirmed.
Bore tolerance — within length, cover, and deviation tolerances.
Permit — uncased installation allowed by the crossing permit.
Key Takeaways Recap
Cased crossings use an outer casing with insulators, end seals, and (for gas) vent pipes; uncased crossings install the pipe directly with a CP-compatible design.
The crossing permit dictates cased vs uncased; railroads and some road authorities still require casing.
Insulators electrically isolate the carrier from the casing; a failed insulator shorts CP and risks corrosion.
Vent pipes on gas casings must be vent-tested open; end seals keep water out of the annulus.
Bore voids and annular spaces may require grouting; the inspector verifies grout placement and that vents are not blocked.