Study guide
4.2 Ellipsoidal & Hemispherical Head Calculations
API 510 Pressure Vessel Inspector Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction, Scope & Certification Requirements
1.1 Exam Structure, Administration & Study Strategy 1.2 API 510 Code Scope, Exclusions & Jurisdictional Boundaries 1.3 Roles, Responsibilities & Inspector Qualification
2 Chapter 2: Inspection Planning, Data Evaluation & Remaining Life
2.1 Corrosion Rates, Remaining Life & Corrosion Allowance Calculations 2.2 Inspection Intervals, On-Stream Inspection & Interval Deferrals 2.3 Condition Monitoring Locations (CMLs) & Data Analysis
3 Chapter 3: Vessel Evaluation, Corrosion Averaging & Fitness-for-Service
3.1 Corrosion Averaging & Minimum Thickness Evaluation 3.2 Pitting Evaluation & Corroded Area Limits 3.3 Fitness-for-Service (API 579-1) & Risk-Based Inspection (API 580)
4 Chapter 4: ASME Section VIII Div 1 Design & Thickness Calculations
4.1 Internal Pressure Design & Cylindrical Shell Calculations 4.2 Ellipsoidal & Hemispherical Head Calculations 4.3 Spherical Shells, Static Head & Vessel MAWP 4.4 Openings, Nozzle Reinforcement & External Pressure Basics
5 Chapter 5: ASME Section VIII Fabrication, Welds & Joint Efficiency
5.1 Weld Joint Categories (UW-3) & Joint Efficiencies (UW-12) 5.2 Radiographic Examination (UW-11, UW-51, UW-52) 5.3 Post-Weld Heat Treatment (PWHT) & Impact Testing (UCS-56, UCS-66)
6 Chapter 6: Welding Inspection & Metallurgy (API 577 & ASME Sec IX)
6.1 Welding Procedures (WPS/PQR) & Essential Variables 6.2 Welder Performance Qualification (WPQ) & Testing 6.3 Welding Processes, Metallurgy & Weld Discontinuities (API 577)
7 Chapter 7: Nondestructive Examination (ASME Section V)
7.1 Radiographic Examination Techniques & Image Quality Indicators (Article 2) 7.2 Ultrasonic Thickness Measurement (Article 23, SE-797) 7.3 ASME Section V Articles 1, 6 & 7: General Requirements, PT & MT
8 Chapter 8: Damage Mechanisms (API RP 571)
8.1 Atmospheric Corrosion & Corrosion Under Insulation 8.2 HTHA, High-Temperature H2/H2S Corrosion & Sulfidation 8.3 Amine, Caustic & Chloride Stress Corrosion Cracking 8.4 Wet H2S Damage, Brittle Fracture & Erosion-Corrosion 8.5 Boiler-Water, Steam-Condensate & Hydrochloric Acid Corrosion 8.6 Caustic Corrosion & Naphthenic Acid Corrosion
9 Chapter 9: Pressure Vessel Inspection Practices (API RP 572 & API RP 578)
9.1 Internal & External Vessel Inspection Practices (API 572) 9.2 Structural Components, Internal Trays, Linings & Skirts 9.3 Material Verification Programs & Positive Material Identification (API 578)
10 Chapter 10: Pressure-Relieving Devices (API RP 576)
10.1 PRD Types, Construction & Operating Principles 10.2 PRD Causes of Failure, Shop Testing & Overhaul 10.3 PRD Inspection Intervals, Records & Rupture Disks
11 Chapter 11: Repairs, Alterations, Rerating & Pressure Testing (API 510 & PCC-2)
11.1 Repair vs. Alteration Authorization, Execution & Methods 11.2 PCC-2 Core Welded Repairs: Articles 101, 201, 202, 211 & 212 11.3 PCC-2 Special Welding: Articles 209, 210, 215 & 216 11.4 PCC-2 Excavation, Flange, Exchanger & Test Articles 304, 305, 312, 501 & 502 11.5 Vessel Rerating Requirements & Engineering Calculations 11.6 Pressure Testing: Hydrostatic, Pneumatic & NDE in Lieu of Testing
4.2 Ellipsoidal & Hemispherical Head Calculations
Key Takeaways Explain This Topic AI
The current API 510 calculation blueprint names 2:1 ellipsoidal and hemispherical heads; Appendix 1 nonstandard-head formulas are expressly excluded.
A standard 2:1 ellipsoidal head uses inside diameter D: t = PD/(2SE - 0.2P).
A hemispherical head uses inside radius L: t = PL/(2SE - 0.2P), so it needs about half the pressure thickness of a 2:1 ellipsoidal head of the same diameter.
Use dimensions in the corroded condition for an in-service evaluation and add the specified future corrosion allowance only after calculating pressure thickness.
For MAWP, solve each formula for P and use the lowest component MAWP after accounting for static head at that component.
Last updated: August 2026
Ellipsoidal & Hemispherical Head Calculations
The current API 510 Body of Knowledge requires internal-pressure calculations for 2:1 semi-ellipsoidal heads and hemispherical heads . It also requires candidates to determine a head's part MAWP and decide whether a measured head thickness is acceptable. Appendix 1 formulas for nonstandard heads are expressly outside the calculation scope. Accordingly, this section concentrates on the two named geometries and does not make torispherical or flat-head sizing part of the study target.
1. Geometry Comes Before Substitution
A 2:1 semi-ellipsoidal head has a major-to-minor axis ratio of 2:1. Its inside depth is approximately one-fourth of its inside diameter. The standard geometry factor is therefore K = 1.0. The formula uses the head's inside diameter D , not its radius.
A hemispherical head is one-half of a sphere. Its inside crown radius L equals one-half of its inside diameter. The formula uses the inside radius L , not diameter. Because pressure creates equal membrane stress in every direction, a hemisphere is structurally efficient and normally needs about half the pressure thickness of a 2:1 ellipsoidal head having the same diameter, pressure, material, and joint efficiency.
- Geometry Dimension used Required pressure thickness Part MAWP
- 2:1 semi-ellipsoidal Inside diameter D t = PD / (2SE - 0.2P) P = 2SEt / (D + 0.2t)
- Hemispherical Inside radius L t = PL / (2SE - 0.2P) P = 2SEt / (L + 0.2t)
Where P is internal pressure at the component, S is allowable stress at the evaluation temperature, E is the applicable joint efficiency, and t is pressure-retaining metal in the corroded condition. Keep units consistent.
2. Corroded Dimensions and Corrosion Allowance
API 510 problems commonly switch between an existing corroded condition and a new-design condition. Read the wording before touching the calculator.
For an existing head evaluated at its current measured thickness, use the current corroded inside dimension and do not subtract the historical corrosion allowance a second time.
If a problem gives an original inside diameter and asks for a required thickness including a future allowance CA, first use the corresponding corroded dimension: D_corroded = D_original + 2CA for diameter, or L_corroded = L_original + CA for radius.
Calculate pressure thickness with the corroded dimension, then add CA to obtain a nominal required thickness for future service.
For a part-MAWP calculation, use only the thickness available for pressure after deducting the future corrosion allowance from the measured or nominal thickness when the problem requires that allowance to remain.
The diameter-versus-radius distinction is a frequent error. Adding a radial corrosion allowance once to a diameter is also wrong; loss on both sides increases the corroded inside diameter by 2CA.
3. Worked Required-Thickness Example
An accumulator has an original inside diameter of 72.0 in. Both heads are seamless. Design pressure is 250 psi, allowable stress is 20,000 psi, E = 1.00, and future corrosion allowance is 0.125 in.
2:1 Ellipsoidal Head
Corroded inside diameter:
D = 72.0 + 2(0.125) = 72.250 in.
Pressure thickness:
t = [250(72.250)] / [2(20,000)(1.00) - 0.2(250)]
t = 18,062.5 / 39,950 = 0.4521 in.
Required nominal thickness including future allowance:
t_required = 0.4521 + 0.125 = 0.5771 in.
Hemispherical Head
Corroded inside radius:
L = 36.0 + 0.125 = 36.125 in.
Pressure thickness:
t = [250(36.125)] / [2(20,000)(1.00) - 0.2(250)]
t = 9,031.25 / 39,950 = 0.2261 in.
Required nominal thickness including future allowance:
t_required = 0.2261 + 0.125 = 0.3511 in.
The pressure portion of the hemispherical result is one-half of the ellipsoidal value because L = D/2 and the denominators are identical. The same fixed corrosion allowance is then added to each.
4. Reversing the Formula for Part MAWP
When actual thickness is known, remove any required future corrosion allowance to obtain t before calculating part MAWP. Then use the inverse formula for the correct geometry. Do not simply divide test pressure or design pressure by a safety factor.
For example, a 2:1 ellipsoidal head has D = 60.0 in., S = 18,000 psi, E = 0.85, and 0.500 in. of pressure-retaining thickness:
- P = [2(18,000)(0.85)(0.500)] / [60.0 + 0.2(0.500)]
- P = 15,300 / 60.1 = 254.6 psi
That is the head's pressure-only part MAWP at the stated temperature. A completed vessel is governed by its weakest component. For a lower component in a liquid-filled vertical vessel, subtract the static head acting at that elevation when expressing the allowable pressure at the top of the vessel.
5. Exam-Safe Workflow
Identify the geometry: 2:1 ellipsoidal or hemispherical.
Decide whether the problem asks for pressure thickness, nominal thickness with CA, or part MAWP.
Put D in the ellipsoidal equation or L in the hemispherical equation.
Use allowable stress at the stated temperature and the applicable joint efficiency.
Treat dimensions and thickness consistently as corroded or uncorroded.
Include static head at the evaluated component when P must represent local pressure.
Keep unrounded values through the calculation and round only the reported result.
Common distractors arise from using radius in the ellipsoidal equation, diameter in the hemispherical equation, adding CA only once to a diameter, adding CA before rather than after the pressure-thickness calculation, or using nominal thickness rather than pressure-retaining thickness in a MAWP calculation.