Study guide
5.1 Weld Joint Categories (UW-3) & Joint Efficiencies (UW-12)
API 510 Pressure Vessel Inspector Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction, Scope & Certification Requirements
1.1 Exam Structure, Administration & Study Strategy 1.2 API 510 Code Scope, Exclusions & Jurisdictional Boundaries 1.3 Roles, Responsibilities & Inspector Qualification
2 Chapter 2: Inspection Planning, Data Evaluation & Remaining Life
2.1 Corrosion Rates, Remaining Life & Corrosion Allowance Calculations 2.2 Inspection Intervals, On-Stream Inspection & Interval Deferrals 2.3 Condition Monitoring Locations (CMLs) & Data Analysis
3 Chapter 3: Vessel Evaluation, Corrosion Averaging & Fitness-for-Service
3.1 Corrosion Averaging & Minimum Thickness Evaluation 3.2 Pitting Evaluation & Corroded Area Limits 3.3 Fitness-for-Service (API 579-1) & Risk-Based Inspection (API 580)
4 Chapter 4: ASME Section VIII Div 1 Design & Thickness Calculations
4.1 Internal Pressure Design & Cylindrical Shell Calculations 4.2 Ellipsoidal & Hemispherical Head Calculations 4.3 Spherical Shells, Static Head & Vessel MAWP 4.4 Openings, Nozzle Reinforcement & External Pressure Basics
5 Chapter 5: ASME Section VIII Fabrication, Welds & Joint Efficiency
5.1 Weld Joint Categories (UW-3) & Joint Efficiencies (UW-12) 5.2 Radiographic Examination (UW-11, UW-51, UW-52) 5.3 Post-Weld Heat Treatment (PWHT) & Impact Testing (UCS-56, UCS-66)
6 Chapter 6: Welding Inspection & Metallurgy (API 577 & ASME Sec IX)
6.1 Welding Procedures (WPS/PQR) & Essential Variables 6.2 Welder Performance Qualification (WPQ) & Testing 6.3 Welding Processes, Metallurgy & Weld Discontinuities (API 577)
7 Chapter 7: Nondestructive Examination (ASME Section V)
7.1 Radiographic Examination Techniques & Image Quality Indicators (Article 2) 7.2 Ultrasonic Thickness Measurement (Article 23, SE-797) 7.3 ASME Section V Articles 1, 6 & 7: General Requirements, PT & MT
8 Chapter 8: Damage Mechanisms (API RP 571)
8.1 Atmospheric Corrosion & Corrosion Under Insulation 8.2 HTHA, High-Temperature H2/H2S Corrosion & Sulfidation 8.3 Amine, Caustic & Chloride Stress Corrosion Cracking 8.4 Wet H2S Damage, Brittle Fracture & Erosion-Corrosion 8.5 Boiler-Water, Steam-Condensate & Hydrochloric Acid Corrosion 8.6 Caustic Corrosion & Naphthenic Acid Corrosion
9 Chapter 9: Pressure Vessel Inspection Practices (API RP 572 & API RP 578)
9.1 Internal & External Vessel Inspection Practices (API 572) 9.2 Structural Components, Internal Trays, Linings & Skirts 9.3 Material Verification Programs & Positive Material Identification (API 578)
10 Chapter 10: Pressure-Relieving Devices (API RP 576)
10.1 PRD Types, Construction & Operating Principles 10.2 PRD Causes of Failure, Shop Testing & Overhaul 10.3 PRD Inspection Intervals, Records & Rupture Disks
11 Chapter 11: Repairs, Alterations, Rerating & Pressure Testing (API 510 & PCC-2)
11.1 Repair vs. Alteration Authorization, Execution & Methods 11.2 PCC-2 Core Welded Repairs: Articles 101, 201, 202, 211 & 212 11.3 PCC-2 Special Welding: Articles 209, 210, 215 & 216 11.4 PCC-2 Excavation, Flange, Exchanger & Test Articles 304, 305, 312, 501 & 502 11.5 Vessel Rerating Requirements & Engineering Calculations 11.6 Pressure Testing: Hydrostatic, Pneumatic & NDE in Lieu of Testing
5.1 Weld Joint Categories (UW-3) & Joint Efficiencies (UW-12)
Key Takeaways Explain This Topic AI
Weld Joint Categories (A, B, C, D per ASME UW-3) define the geometric location and stress state of a joint on a pressure vessel, completely independent of the weld joint type (Type 1 to 6) or the degree of nondestructive examination.
Category A comprises longitudinal seams, joints within spheres/heads, and hemispherical head-to-shell welds; Category B comprises circumferential shell seams and shell-to-ellipsoidal/torispherical head welds.
Table UW-12 establishes joint efficiency (E) based on weld type and radiography: Type 1 double-welded butt joints yield E = 1.00 (Full RT), E = 0.85 (Spot RT), and E = 0.70 (No RT / Visual only).
Per UW-12(d), a seamless formed head attached via a Category B circumferential butt weld qualifies for E = 1.00 in head thickness formulas only if that circumferential weld is spot radiographed per UW-11(a)(5)(b); otherwise, E = 0.85 must be used.
UW-12(e) treats welded pipe/tubing like seamless product for this purpose, using welded-product allowable-stress values and applying UW-12(d); product form and stress-table notes must be checked.
Last updated: August 2026
Weld Joint Categories (UW-3) & Joint Efficiencies (UW-12)
In ASME Boiler and Pressure Vessel Code (BPVC) Section VIII, Division 1, the design thickness of every pressure-containing component depends directly on the Joint Efficiency ( E E E ) . The joint efficiency is a numerical safety factor (ranging from 0.45 0.45 0.45 to 1.00 1.00 1.00 ) that quantifies the structural integrity and quality level of a welded joint relative to the solid base metal.
To determine the correct joint efficiency for thickness and Maximum Allowable Working Pressure (MAWP) calculations, the API 510 Authorized Inspector must master two distinct concepts that are frequently confused: Weld Joint Categories (ASME UW-3) and Weld Joint Types (ASME UW-12) .
1. Weld Joint Categories (ASME UW-3)
ASME Section VIII, Division 1, paragraph UW-3 establishes four Joint Categories: A, B, C, and D . +-----------------------------------------------------------------------------------------+
- | ASME SECTION VIII, DIV 1 - JOINT CATEGORIES (UW-3) |
- | |
- | [CATEGORY A] [CATEGORY B] [CATEGORY C] |
- | Longitudinal Seams, Circumferential Seams, Flanges, Tubesheets, |
- | Hemispherical Head/Shell, Ellipsoidal/Torispherical Flat Heads to |
- | Joints Within Heads/Spheres Head-to-Shell Welds Shell/Nozzles |
- | | | | |
- | v v v |
- | +-------------------------------------------------------------------+ |
- | | (A) Head Seam | |
- | +--+-------------------+-----------+-------------------+---------------+--+ |
- | / | | | | | \\ |
- | | (A)| (A) LONG SEAM | (B) CIRC | (A) LONG SEAM | (B) CIRC | (B)| (Head)|
- | |Head|===================| SEAM |===================| SEAM |Head| Toris-|
- | |Hemi| | | | |2:1 |pherical|
- | \\ | | | (D) NOZZLE | (C) FLANGE | / |
- | +--+-------------------+-----------+---[===|===]-------+---[=========]-+---+ |
- | | | |
- | v v |
- | [CATEGORY D] [CATEGORY C] |
- | Nozzles, Branch Bolted Flange |
- | Pipes to Shell/Head to Nozzle Neck |
- +-----------------------------------------------------------------------------------------+
Important
Critical Principle: Joint Categories designate the location of the joint on the vessel , NOT the type of weld (e.g., butt weld vs. fillet weld) and NOT the degree of examination (e.g., Full RT vs. Spot RT).
Detailed Breakdown of Joint Categories (UW-3)
Joint Category Geometric Locations & Vessel Components Included Key Stress & Operational Considerations
Category A • Longitudinal welded joints in the main cylindrical shell, communicating chambers, transitions in diameter, or nozzle necks.; • Any welded joint within a sphere , a formed head (e.g., petal welds, crown-to-petal seams), or a flat head.; • Circumferential welded joints connecting hemispherical heads to main shells, transitions, or nozzles. Governed by maximum primary membrane stress ( circumferential hoop stress σ h = P R / t \sigma_h = PR/t σ h = PR / t ). The highest stress category on a cylindrical vessel.
Category B • Circumferential welded joints in the main cylindrical shell, communicating chambers, transitions, or nozzle necks.; • Circumferential welded joints connecting formed heads other than hemispherical (e.g., 2:1 ellipsoidal, torispherical, or conical heads) to main shells, transitions, or nozzles. Governed by primary longitudinal stress ( σ L = P R / 2 t = 0.5 σ h \sigma_L = PR/2t = 0.5\sigma_h σ L = PR /2 t = 0.5 σ h ). Experiences half the internal pressure stress of Category A.
Category C • Welded joints connecting flanges, Van Stone laps, tubesheets, or flat heads to the main shell, formed heads, transitions, nozzle necks, or communicating chambers.; • Any welded joint connecting one side plate to another side plate of a flat-sided vessel. Subject to complex bending moments, rotational deflection, and longitudinal shear at flanged/tubesheet junctions.
Category D • Welded joints connecting communicating chambers or nozzles to main shells, spheres, transitions, heads, or flat-sided vessels.; • Welded joints connecting nozzles to communicating chambers. Subject to high stress concentrations around openings, localized membrane stress, and external nozzle piping loads.
Warning
The Hemispherical Head Exam Trap: A circumferential weld connecting a hemispherical head to a cylindrical shell is classified as a Category A joint. Conversely, a circumferential weld connecting a 2:1 semi-ellipsoidal or torispherical head to a cylindrical shell is classified as a Category B joint. This distinction is one of the most frequently tested concepts on the API 510 exam.
Welded Pipe and Tubing — UW-12(e)
Purchased welded pipe or tubing is not handled as a plate-fabricated shell seam by simply choosing a Table UW-12 row for the mill seam. UW-12(e) directs the user to treat welded pipe or tubing in the same manner as seamless material, but to take allowable tensile stress from the welded-product values in the stress tables and apply the UW-12(d) requirements. Check the exact product form and stress-table notes; do not combine a welded-product stress reduction with an invented second joint-efficiency penalty.
Loading diagram... ASME Section VIII UW-3 Joint Category Classification Logic
2. ASME Weld Joint Types (UW-12)
While UW-3 dictates where a joint is located, UW-12 defines how the weld is physically constructed. ASME Section VIII Division 1 recognizes six fundamental Weld Types : +-----------------------------------------------------------------------------------------+
- | ASME SECTION VIII WELD TYPES (1 THROUGH 6) |
- | |
- | [TYPE 1: BUTT WELD BOTH SIDES / EQUIVALENT] [TYPE 2: BUTT WELD WITH BACKING] |
- | Weld Cap Inside & Outside Single-Welded with Backing |
- | +---[WELD]---+ +---[WELD]---+ |
- | | ====== | | ====== | |
- | +---[WELD]---+ +--[BACKING]-+ |
- | |
- | [TYPE 3: BUTT WELD WITHOUT BACKING] [TYPE 4: DOUBLE FULL-FILLET LAP] |
- | Single-Welded (No Backing) Two Fillet Welds on Lap |
- | +---[WELD]---+ +========[FILLET] |
- | | ====== | | PLATE 1 | |
- | +------------+ (Root Open) +-[FILLET]===+ |
- | | PLATE 2 | |
- | +------------+ |
- | [TYPE 5: SINGLE FILLET LAP W/ PLUGS] [TYPE 6: SINGLE FILLET LAP NO PLUG] |
- | Lap with Fillet + Plug Welds Single Lap Fillet Only |
- +-----------------------------------------------------------------------------------------+
- Detailed Descriptions and Construction Constraints
Type 1: Butt Joints (Double-Welded or Equivalent):
Welded from both sides (double-welded) or welded from one side with full penetration and complete fusion achieved by backgouging/grinding and welding the reverse side, or using consumable inserts / gas tungsten arc welding (GTAW) root passes that meet UW-35.
Allowed Categories: A, B, C, and D.
Maximum Joint Efficiency: E = 1.00 E = 1.00 E = 1.00 (Full RT), E = 0.85 E = 0.85 E = 0.85 (Spot RT), E = 0.70 E = 0.70 E = 0.70 (No RT).
Type 2: Single-Welded Butt Joint with Backing Strip:
Welded from one side onto a backing strip that remains in place after welding.
Allowed Categories: A, B, C, and D (with thickness and geometry limitations).
Maximum Joint Efficiency: E = 0.90 E = 0.90 E = 0.90 (Full RT), E = 0.80 E = 0.80 E = 0.80 (Spot RT), E = 0.65 E = 0.65 E = 0.65 (No RT).
Code Restriction: If the backing strip is left in place on longitudinal seams (Category A), it must be non-fusible or of material compatible with the base plate.
Type 3: Single-Welded Butt Joint Without Backing Strip:
Welded from one side only without the use of backing material and without backwelding from the inside.
Allowed Categories: Category A and B only, subject to strict thickness limits (generally t ≤ 5 / 8 in. t \le 5/8\text{ in.} t ≤ 5/8 in. [ 16 mm 16\text{ mm} 16 mm ] for Category A, and prohibited for vessels in lethal or low-temperature service).
Maximum Joint Efficiency: E = 0.60 E = 0.60 E = 0.60 (No RT only; Spot and Full RT are not permitted ).
Type 4: Double Full-Fillet Lap Joint:
Plates overlap, and a full fillet weld is applied along both overlapping edges.
Allowed Categories: Category A (circumferential shells ≤ 3 / 8 in. \le 3/8\text{ in.} ≤ 3/8 in. ), Category B (shells ≤ 5 / 8 in. \le 5/8\text{ in.} ≤ 5/8 in. , or heads ≤ 5 / 8 in. \le 5/8\text{ in.} ≤ 5/8 in. ). Prohibited for Category D nozzles.
Maximum Joint Efficiency: E = 0.55 E = 0.55 E = 0.55 (No RT only).
Type 5: Single Full-Fillet Lap Joint with Plug Welds:
Plates overlap, with one full fillet weld at the edge plus plug welds through holes in the overlapping plate.
Allowed Categories: Category B (for shell attachments and head attachments ≤ 1 / 2 in. \le 1/2\text{ in.} ≤ 1/2 in. ) and Category C.
Maximum Joint Efficiency: E = 0.50 E = 0.50 E = 0.50 (No RT only).
Type 6: Single Full-Fillet Lap Joint Without Plug Welds:
Overlapping joint secured by a single fillet weld without plug welds.
Allowed Categories: Category A (for heads attached to shells ≤ 24 in. \le 24\text{ in.} ≤ 24 in. OD and thickness ≤ 1 / 4 in. \le 1/4\text{ in.} ≤ 1/4 in. ) and Category B.
Maximum Joint Efficiency: E = 0.45 E = 0.45 E = 0.45 (No RT only).
3. Master ASME Section VIII Table UW-12 Joint Efficiency Matrix
The following table synthesizes the complete joint efficiency factors ( E E E ) codified in Table UW-12 of ASME Section VIII, Division 1:
Weld Type Joint Description Limitations & Joint Categories Full RT (UW-11(a)) Spot RT (UW-11(b), UW-52) No RT (Visual Only)
Type 1 Butt joints as attained by double-welding or other means which will obtain the same quality of deposited weld metal Categories A, B, C, D 1.00 1.00 1.00 0.85 0.85 0.85 0.70 0.70 0.70
Type 2 Single-welded butt joint with backing strip which will remain in place Categories A, B, C, D (Longitudinal backing strips must be compatible) 0.90 0.90 0.90 0.80 0.80 0.80 0.65 0.65 0.65
Type 3 Single-welded butt joint without use of backing strip Circumferential joints only; max t = 5 / 8 in. t = 5/8\text{ in.} t = 5/8 in. ( 16 mm 16\text{ mm} 16 mm ) N/A N/A 0.60 0.60 0.60
Type 4 Double full-fillet lap joint Longitudinal max t = 3 / 8 in. t = 3/8\text{ in.} t = 3/8 in. ; Circ max t = 5 / 8 in. t = 5/8\text{ in.} t = 5/8 in. N/A N/A 0.55 0.55 0.55
Type 5 Single full-fillet lap joint with plug welds Circ joints only; max t = 1 / 2 in. t = 1/2\text{ in.} t = 1/2 in. ( 13 mm 13\text{ mm} 13 mm ) N/A N/A 0.50 0.50 0.50
Type 6 Single full-fillet lap joint without plug welds For heads convex to pressure; max t = 1 / 4 in. t = 1/4\text{ in.} t = 1/4 in. ( 6 mm 6\text{ mm} 6 mm ) N/A N/A 0.45 0.45 0.45
4. Seamless Component Joint Efficiency Rules (UW-12(d), UW-12(e), UW-11(a)(5)(b))
One of the highest-yield calculation areas on the API 510 exam is the selection of joint efficiency E E E for seamless cylindrical shells, seamless pipe, and seamless formed heads .
The Seamless Paradox
A seamless component has no longitudinal weld seam ( E = 1.00 E = 1.00 E = 1.00 for base wrought material). However, when a seamless head or shell is welded into a vessel, its design thickness formula may be forced to take a joint efficiency penalty based on how the circumferential attaching weld (Category B) is radiographed! +-----------------------------------------------------------------------------------------+
- | SEAMLESS HEAD & SHELL EFFICIENCY RULES (UW-12(d)) |
- | |
- | +---------------------------------------------------------------------------------+ |
- | | SEAMLESS FORMED HEAD (Ellipsoidal / Torispherical) | |
- | | Category A (Seamless Wrought Material = 1.00 Base) | |
- | +---------------------------------------------------------------------------------+ |
- | | |
- | v |
- | ============== CATEGORY B CIRCUMFERENTIAL ATTACHING BUTT WELD ===================== |
- | | |
- | +------------------------------+------------------------------+ |
- | | | |
- | v v |
- | [CONDITION 1: SPOT RT PERFORMED] [CONDITION 2: NO SPOT RT] |
- | - Cat B weld meets UW-11(a)(5)(b) - Cat B weld visual only |
- | - At least 1 spot RT per 50 ft - No RT performed |
- | | | |
- | v v |
- | ================================== ==================== |
- | HEAD FORMULA EFFICIENCY: E = 1.00 HEAD FORMULA: E = 0.85 |
- | ================================== ==================== |
- +-----------------------------------------------------------------------------------------+
Detailed Rules under UW-12(d):
Seamless Formed Heads (Ellipsoidal, Torispherical, Hemispherical without seams):
When a seamless formed head is attached to a cylindrical shell by a Type 1 Category B butt weld :
If the Category B weld is Spot Radiographed per UW-11(a)(5)(b), use E = 1.00 E = 1.00 E = 1.00 in the head thickness formula (UG-32).
If the Category B weld is NOT radiographed (Visual examination only), use E = 0.85 E = 0.85 E = 0.85 in the head thickness formula.
When attached by a Type 2 Category B butt weld (with backing strip):
If Spot Radiographed per UW-11(a)(5)(b), use E = 0.90 E = 0.90 E = 0.90 .
If NOT radiographed, use E = 0.80 E = 0.80 E = 0.80 .
Seamless Cylindrical Shells / Seamless Pipe:
Circumferential (Hoop) Stress Formula ( t = P R S E − 0.6 P t = \frac{PR}{SE - 0.6P} t = SE − 0.6 P PR ):
If the Category B circumferential butt welds connecting shell courses or heads receive Spot Radiography per UW-11(a)(5)(b), use E = 1.00 E = 1.00 E = 1.00 for the hoop stress calculation.
If the Category B circumferential butt welds receive NO Radiography , use E = 0.85 E = 0.85 E = 0.85 for the hoop stress calculation.
Longitudinal Stress Formula ( t = P R 2 S E + 0.4 P t = \frac{PR}{2SE + 0.4P} t = 2 SE + 0.4 P PR ):
Longitudinal stress acts directly across the Category B circumferential seam. Therefore, the longitudinal calculation uses the actual efficiency of the circumferential seam ( E = 1.00 E = 1.00 E = 1.00 for Full RT, E = 0.85 E = 0.85 E = 0.85 for Spot RT, E = 0.70 E = 0.70 E = 0.70 for No RT).
Welded Formed Heads (Heads fabricated from welded sections):
If a formed head contains a welded seam (e.g., two half-dishes joined by a Category A butt weld):
The efficiency E E E used in the head formula is governed by the Category A weld seam within the head ( E = 1.00 E = 1.00 E = 1.00 if fully radiographed, E = 0.85 E = 0.85 E = 0.85 if spot radiographed, E = 0.70 E = 0.70 E = 0.70 if unradiographed), provided the Category B attachment weld meets UW-11(a)(5)(b).
Summary Table: Seamless Component Joint Efficiency Selection
Component Being Evaluated Attachment Weld Type Radiography on Attachment Joint Efficiency ( E E E ) for Thickness Formula
- Seamless Head (UG-32) Type 1 Butt Weld Full RT or Spot RT per UW-11(a)(5)(b) 1.00 1.00 1.00
- Seamless Head (UG-32) Type 1 Butt Weld No Radiography (Visual Only) 0.85 0.85 0.85
- Seamless Head (UG-32) Type 2 Butt Weld w/ Backing Spot RT per UW-11(a)(5)(b) 0.90 0.90 0.90
- Seamless Head (UG-32) Type 2 Butt Weld w/ Backing No Radiography (Visual Only) 0.80 0.80 0.80
- Seamless Shell (Hoop Stress) Type 1 Girth Seams Spot RT per UW-11(a)(5)(b) 1.00 1.00 1.00
- Seamless Shell (Hoop Stress) Type 1 Girth Seams No Radiography (Visual Only) 0.85 0.85 0.85
- Welded Head (Cat A Type 1) Type 1 Girth Seams Spot RT on Cat A, Spot RT on Cat B 0.85 0.85 0.85
- Welded Head (Cat A Type 1) Type 1 Girth Seams No RT on Cat A, No RT on Cat B 0.70 0.70 0.70
- 5. Comprehensive Step-by-Step Calculation Examples
- Example 1: Welded Cylindrical Shell Thickness Sensitivity
Problem: A pressure vessel cylindrical shell is designed with SA-516 Gr 70 plate ( S = 20 , 000 psi S = 20,000\text{ psi} S = 20 , 000 psi ) for an internal design pressure P = 300 psig P = 300\text{ psig} P = 300 psig and inside radius R = 30.0 in. R = 30.0\text{ in.} R = 30.0 in. . Longitudinal joints are Type 1 butt welds. Calculate the minimum required thickness ( t min t_{\text{min}} t min ) under three fabrication options:
- Option A: Full Radiography (RT-1)
- Option B: Spot Radiography (RT-3)
- Option C: No Radiography (Visual Only)
Calculations: Using ASME Section VIII Div 1 UG-27(c)(1): t min = P ⋅ R S ⋅ E − 0.6 ⋅ P t_{\text{min}} = \frac{P \cdot R}{S \cdot E - 0.6 \cdot P} t min = S ⋅ E − 0.6 ⋅ P P ⋅ R
Option A (Full RT, E = 1.00 E = 1.00 E = 1.00 ): t min = 300 × 30.0 ( 20 , 000 × 1.00 ) − ( 0.6 × 300 ) = 9 , 000 20 , 000 − 180 = 9 , 000 19 , 820 = 0.454 in. t_{\text{min}} = \frac{300 \times 30.0}{(20,000 \times 1.00) - (0.6 \times 300)} = \frac{9,000}{20,000 - 180} = \frac{9,000}{19,820} = \mathbf{0.454\text{ in.}} t min = ( 20 , 000 × 1.00 ) − ( 0.6 × 300 ) 300 × 30.0 = 20 , 000 − 180 9 , 000 = 19 , 820 9 , 000 = 0.454 in.
Option B (Spot RT, E = 0.85 E = 0.85 E = 0.85 ): t min = 300 × 30.0 ( 20 , 000 × 0.85 ) − ( 0.6 × 300 ) = 9 , 000 17 , 000 − 180 = 9 , 000 16 , 820 = 0.535 in. t_{\text{min}} = \frac{300 \times 30.0}{(20,000 \times 0.85) - (0.6 \times 300)} = \frac{9,000}{17,000 - 180} = \frac{9,000}{16,820} = \mathbf{0.535\text{ in.}} t min = ( 20 , 000 × 0.85 ) − ( 0.6 × 300 ) 300 × 30.0 = 17 , 000 − 180 9 , 000 = 16 , 820 9 , 000 = 0.535 in.
Option C (No RT, E = 0.70 E = 0.70 E = 0.70 ): t min = 300 × 30.0 ( 20 , 000 × 0.70 ) − ( 0.6 × 300 ) = 9 , 000 14 , 000 − 180 = 9 , 000 13 , 820 = 0.651 in. t_{\text{min}} = \frac{300 \times 30.0}{(20,000 \times 0.70) - (0.6 \times 300)} = \frac{9,000}{14,000 - 180} = \frac{9,000}{13,820} = \mathbf{0.651\text{ in.}} t min = ( 20 , 000 × 0.70 ) − ( 0.6 × 300 ) 300 × 30.0 = 14 , 000 − 180 9 , 000 = 13 , 820 9 , 000 = 0.651 in.
Engineering Insight: Moving from Full RT ( 0.454 in. 0.454\text{ in.} 0.454 in. ) to No RT ( 0.651 in. 0.651\text{ in.} 0.651 in. ) requires a 43.4% increase in plate thickness , highlighting why radiography is economically essential in heavy-wall vessels.
Example 2: Seamless 2:1 Semi-Ellipsoidal Head Calculation
Problem: A seamless 2:1 semi-ellipsoidal head ( D = 60.0 in. D = 60.0\text{ in.} D = 60.0 in. ) made of SA-516 Gr 70 ( S = 20 , 000 psi S = 20,000\text{ psi} S = 20 , 000 psi ) operates at P = 250 psig P = 250\text{ psig} P = 250 psig . The head is attached to a cylindrical shell via a Type 1 circumferential butt weld.
Calculate the required thickness ( t head t_{\text{head}} t head ) under two conditions:
The shell-to-head Category B circumferential weld receives Spot Radiography per UW-11(a)(5)(b).
The shell-to-head Category B circumferential weld receives No Radiography.
Calculations: Using ASME Section VIII Div 1 UG-32(d): t head = P ⋅ D 2 ⋅ S ⋅ E − 0.2 ⋅ P t_{\text{head}} = \frac{P \cdot D}{2 \cdot S \cdot E - 0.2 \cdot P} t head = 2 ⋅ S ⋅ E − 0.2 ⋅ P P ⋅ D
Condition 1 (Spot RT on Girth Weld → E = 1.00 \rightarrow E = 1.00 → E = 1.00 ): t head = 250 × 60.0 ( 2 × 20 , 000 × 1.00 ) − ( 0.2 × 250 ) = 15 , 000 40 , 000 − 50 = 15 , 000 39 , 950 = 0.3755 in. t_{\text{head}} = \frac{250 \times 60.0}{(2 \times 20,000 \times 1.00) - (0.2 \times 250)} = \frac{15,000}{40,000 - 50} = \frac{15,000}{39,950} = \mathbf{0.3755\text{ in.}} t head = ( 2 × 20 , 000 × 1.00 ) − ( 0.2 × 250 ) 250 × 60.0 = 40 , 000 − 50 15 , 000 = 39 , 950 15 , 000 = 0.3755 in.
Condition 2 (No RT on Girth Weld → E = 0.85 \rightarrow E = 0.85 → E = 0.85 ): t head = 250 × 60.0 ( 2 × 20 , 000 × 0.85 ) − ( 0.2 × 250 ) = 15 , 000 34 , 000 − 50 = 15 , 000 33 , 950 = 0.4418 in. t_{\text{head}} = \frac{250 \times 60.0}{(2 \times 20,000 \times 0.85) - (0.2 \times 250)} = \frac{15,000}{34,000 - 50} = \frac{15,000}{33,950} = \mathbf{0.4418\text{ in.}} t head = ( 2 × 20 , 000 × 0.85 ) − ( 0.2 × 250 ) 250 × 60.0 = 34 , 000 − 50 15 , 000 = 33 , 950 15 , 000 = 0.4418 in.
Exam Rule: Failing to spot radiograph the circumferential attachment weld penalizes the seamless head by 17.7 % 17.7\% 17.7% in required thickness.
6. Common Exam Traps: Joint Categories & Efficiencies
Exam Trap Common Misconception Correct ASME Code Rule
Category vs. Type Assuming Category A means Type 1 double-welded butt joint Category defines location (UW-3); Type defines construction geometry (UW-12). A Category A joint can be Type 1, Type 2, or Type 3.
Hemi-Head Category Treating shell-to-hemispherical head welds as Category B Circumferential welds attaching hemispherical heads are Category A (UW-3(a)(1)).
Backing Strip Efficiency Using E = 1.00 E = 1.00 E = 1.00 for fully radiographed joints with backing strips left in place Single-welded butt joints with permanent backing strips are Type 2 , capped at E = 0.90 E = 0.90 E = 0.90 even with 100% Full RT (Table UW-12).
Seamless Head E E E Value Assuming seamless heads always take E = 1.00 E = 1.00 E = 1.00 Seamless heads take E = 0.85 E = 0.85 E = 0.85 if the Category B circumferential attachment seam receives no spot radiography (UW-12(d)).