Study guide
7.2 Ultrasonic Thickness Measurement (Article 23, SE-797)
API 510 Pressure Vessel Inspector Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction, Scope & Certification Requirements
1.1 Exam Structure, Administration & Study Strategy 1.2 API 510 Code Scope, Exclusions & Jurisdictional Boundaries 1.3 Roles, Responsibilities & Inspector Qualification
2 Chapter 2: Inspection Planning, Data Evaluation & Remaining Life
2.1 Corrosion Rates, Remaining Life & Corrosion Allowance Calculations 2.2 Inspection Intervals, On-Stream Inspection & Interval Deferrals 2.3 Condition Monitoring Locations (CMLs) & Data Analysis
3 Chapter 3: Vessel Evaluation, Corrosion Averaging & Fitness-for-Service
3.1 Corrosion Averaging & Minimum Thickness Evaluation 3.2 Pitting Evaluation & Corroded Area Limits 3.3 Fitness-for-Service (API 579-1) & Risk-Based Inspection (API 580)
4 Chapter 4: ASME Section VIII Div 1 Design & Thickness Calculations
4.1 Internal Pressure Design & Cylindrical Shell Calculations 4.2 Ellipsoidal & Hemispherical Head Calculations 4.3 Spherical Shells, Static Head & Vessel MAWP 4.4 Openings, Nozzle Reinforcement & External Pressure Basics
5 Chapter 5: ASME Section VIII Fabrication, Welds & Joint Efficiency
5.1 Weld Joint Categories (UW-3) & Joint Efficiencies (UW-12) 5.2 Radiographic Examination (UW-11, UW-51, UW-52) 5.3 Post-Weld Heat Treatment (PWHT) & Impact Testing (UCS-56, UCS-66)
6 Chapter 6: Welding Inspection & Metallurgy (API 577 & ASME Sec IX)
6.1 Welding Procedures (WPS/PQR) & Essential Variables 6.2 Welder Performance Qualification (WPQ) & Testing 6.3 Welding Processes, Metallurgy & Weld Discontinuities (API 577)
7 Chapter 7: Nondestructive Examination (ASME Section V)
7.1 Radiographic Examination Techniques & Image Quality Indicators (Article 2) 7.2 Ultrasonic Thickness Measurement (Article 23, SE-797) 7.3 ASME Section V Articles 1, 6 & 7: General Requirements, PT & MT
8 Chapter 8: Damage Mechanisms (API RP 571)
8.1 Atmospheric Corrosion & Corrosion Under Insulation 8.2 HTHA, High-Temperature H2/H2S Corrosion & Sulfidation 8.3 Amine, Caustic & Chloride Stress Corrosion Cracking 8.4 Wet H2S Damage, Brittle Fracture & Erosion-Corrosion 8.5 Boiler-Water, Steam-Condensate & Hydrochloric Acid Corrosion 8.6 Caustic Corrosion & Naphthenic Acid Corrosion
9 Chapter 9: Pressure Vessel Inspection Practices (API RP 572 & API RP 578)
9.1 Internal & External Vessel Inspection Practices (API 572) 9.2 Structural Components, Internal Trays, Linings & Skirts 9.3 Material Verification Programs & Positive Material Identification (API 578)
10 Chapter 10: Pressure-Relieving Devices (API RP 576)
10.1 PRD Types, Construction & Operating Principles 10.2 PRD Causes of Failure, Shop Testing & Overhaul 10.3 PRD Inspection Intervals, Records & Rupture Disks
11 Chapter 11: Repairs, Alterations, Rerating & Pressure Testing (API 510 & PCC-2)
11.1 Repair vs. Alteration Authorization, Execution & Methods 11.2 PCC-2 Core Welded Repairs: Articles 101, 201, 202, 211 & 212 11.3 PCC-2 Special Welding: Articles 209, 210, 215 & 216 11.4 PCC-2 Excavation, Flange, Exchanger & Test Articles 304, 305, 312, 501 & 502 11.5 Vessel Rerating Requirements & Engineering Calculations 11.6 Pressure Testing: Hydrostatic, Pneumatic & NDE in Lieu of Testing
7.2 Ultrasonic Thickness Measurement (Article 23, SE-797)
Key Takeaways Explain This Topic AI
The current sheet includes Section V Article 23 only through SE-797 for ultrasonic thickness measurement; Article 4 is not listed.
Pulse-echo thickness uses acoustic velocity and round-trip time, so velocity, temperature, coating, coupling, curvature, or an internal reflector can create error.
Calibration should bracket expected wall when practical and must be verified; failed verification makes later readings suspect.
One point is insufficient for pitting, grooving, erosion, or impingement; scan enough area to locate the true minimum.
Records preserve CML, location, units, instrument/probe, calibration, temperature, surface/coating, operator, date, and verification.
Last updated: August 2026
Ultrasonic Thickness Measurement (Article 23, SE-797)
The September 2026-May 2027 API 510 effectivity sheet includes ASME Section V Article 23 only through SE-797 for ultrasonic testing. It does not include Article 4. The exam task is manual pulse-echo contact thickness measurement: obtaining a defensible wall reading, recognizing bad data, and preserving information for corrosion-rate and remaining-life decisions. Article 4 weld-flaw calibration blocks, DAC/TCG, PAUT, and TOFD may matter in field practice but are outside the listed Section V scope.
1. What the instrument measures
A gauge sends a longitudinal-wave pulse into the component and measures round-trip travel time to the back wall. Displayed thickness is acoustic velocity x round-trip time / 2 . The gauge interprets time using its entered velocity; it does not directly see metal. Material, temperature, surface, coating, couplant, and reflector geometry can all change the indication.
- Influence Typical effect Response
- Wrong material velocity Systematic high or low readings Calibrate on acoustically similar material
- Hot surface Ambient calibration can read falsely high Use approved hot-service correction
- Coating Coating time may be added Use a qualified coating-discrimination mode
- Rough scale or poor coupling Weak or unstable echoes Prepare surface and repeat
- Lamination or inclusion Early reflector imitates thin wall Inspect waveform or verify otherwise
- Deep narrow pit Probe may bridge the minimum Scan an area with suitable probe
- 2. Procedure, equipment, and calibration
A written technique identifies instrument, probe, material, expected range, surface, couplant, calibration standard, scan pattern, temperature limits, and recording rules. Equipment range and resolution must cover expected wall.
Calibrate with a known, acoustically similar standard. A two-point calibration bracketing expected thickness is preferable when supported because it checks zero offset and velocity. Verify calibration at the start and end and at procedure intervals. If verification is outside tolerance, readings since the last acceptable check are suspect and must be evaluated or repeated; adjusting the gauge does not validate prior data.
Couplant removes the air gap. Use enough for stable transmission without a thick variable layer that distorts a delay-line measurement. Keep probe pressure and orientation consistent, particularly on small-radius nozzles and rough surfaces.
3. Repeatable sequence
Confirm component, CML, material, nominal wall, and expected mechanism.
Verify instrument, battery, transducer face, cable, and calibration status.
Clean loose scale without grinding away meaningful base metal.
Calibrate or verify over the expected range.
Seat the probe squarely and obtain a stable repeatable indication.
Scan enough to find localized minima instead of recording the first value.
Repeat an unexpected value after cleaning and calibration checks; preserve a low until disproved.
Record value, units, location, equipment/probe, temperature, coating, calibration, operator, and date.
Reverify calibration at completion and resolve drift.
4. Temperature, coatings, curvature, and local damage
An ambient calibration on hot carbon steel usually overstates thickness because acoustic velocity falls as temperature rises. A field rule of thumb is about one percent indicated-thickness correction per 100 F above calibration, but use the approved correction for actual material and temperature. A rule of thumb is not a qualified procedure.
Paint and polymers have different velocities from steel. A first-echo reading can include coating time and read too thick. Coating-discrimination, multiple-echo, or echo-to-echo modes remove it only when instrument, probe, range, and procedure are suitable.
One point is inadequate for pitting, grooving, erosion, impingement, or under-deposit attack. Treat the CML as an area: scan, confirm the minimum, and record its reproducible location. Curved small nozzles require a suitable small footprint and stable seating.
5. Turning data into evidence
Compare new, baseline, and previous values, calculate long- and short-term rates, and investigate trend changes. A negative rate may reflect changed location, coating, calibration, temperature, or prior quality; it does not prove growth. An abrupt low may be real damage. Review data with the mechanism, required thickness, remaining allowance, and interval.
Exam traps
Article 23 SE-797 is listed; Article 4 weld examination is not.
Section V explains performance and records; acceptance comes from the referencing code.
Stable coupling does not eliminate calibration, velocity, temperature, or location error.
Never delete a low simply because it disrupts a trend.
6. Worked data-quality decision
Suppose a CML previously read 0.500 in. at ambient temperature and now reads 0.535 in. on a hot coated surface. Do not calculate a negative corrosion rate and extend the interval. First confirm the exact location, clean or account for coating by the qualified mode, verify calibration and material velocity, record temperature, and repeat the scan. If the corrected minimum is 0.470 in., that verified value enters the trend. The scenario tests the essential distinction between instrument display and accepted inspection data.