Study guide
11.4 PCC-2 Excavation, Flange, Exchanger & Test Articles 304, 305, 312, 501 & 502
API 510 Pressure Vessel Inspector Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction, Scope & Certification Requirements
1.1 Exam Structure, Administration & Study Strategy 1.2 API 510 Code Scope, Exclusions & Jurisdictional Boundaries 1.3 Roles, Responsibilities & Inspector Qualification
2 Chapter 2: Inspection Planning, Data Evaluation & Remaining Life
2.1 Corrosion Rates, Remaining Life & Corrosion Allowance Calculations 2.2 Inspection Intervals, On-Stream Inspection & Interval Deferrals 2.3 Condition Monitoring Locations (CMLs) & Data Analysis
3 Chapter 3: Vessel Evaluation, Corrosion Averaging & Fitness-for-Service
3.1 Corrosion Averaging & Minimum Thickness Evaluation 3.2 Pitting Evaluation & Corroded Area Limits 3.3 Fitness-for-Service (API 579-1) & Risk-Based Inspection (API 580)
4 Chapter 4: ASME Section VIII Div 1 Design & Thickness Calculations
4.1 Internal Pressure Design & Cylindrical Shell Calculations 4.2 Ellipsoidal & Hemispherical Head Calculations 4.3 Spherical Shells, Static Head & Vessel MAWP 4.4 Openings, Nozzle Reinforcement & External Pressure Basics
5 Chapter 5: ASME Section VIII Fabrication, Welds & Joint Efficiency
5.1 Weld Joint Categories (UW-3) & Joint Efficiencies (UW-12) 5.2 Radiographic Examination (UW-11, UW-51, UW-52) 5.3 Post-Weld Heat Treatment (PWHT) & Impact Testing (UCS-56, UCS-66)
6 Chapter 6: Welding Inspection & Metallurgy (API 577 & ASME Sec IX)
6.1 Welding Procedures (WPS/PQR) & Essential Variables 6.2 Welder Performance Qualification (WPQ) & Testing 6.3 Welding Processes, Metallurgy & Weld Discontinuities (API 577)
7 Chapter 7: Nondestructive Examination (ASME Section V)
7.1 Radiographic Examination Techniques & Image Quality Indicators (Article 2) 7.2 Ultrasonic Thickness Measurement (Article 23, SE-797) 7.3 ASME Section V Articles 1, 6 & 7: General Requirements, PT & MT
8 Chapter 8: Damage Mechanisms (API RP 571)
8.1 Atmospheric Corrosion & Corrosion Under Insulation 8.2 HTHA, High-Temperature H2/H2S Corrosion & Sulfidation 8.3 Amine, Caustic & Chloride Stress Corrosion Cracking 8.4 Wet H2S Damage, Brittle Fracture & Erosion-Corrosion 8.5 Boiler-Water, Steam-Condensate & Hydrochloric Acid Corrosion 8.6 Caustic Corrosion & Naphthenic Acid Corrosion
9 Chapter 9: Pressure Vessel Inspection Practices (API RP 572 & API RP 578)
9.1 Internal & External Vessel Inspection Practices (API 572) 9.2 Structural Components, Internal Trays, Linings & Skirts 9.3 Material Verification Programs & Positive Material Identification (API 578)
10 Chapter 10: Pressure-Relieving Devices (API RP 576)
10.1 PRD Types, Construction & Operating Principles 10.2 PRD Causes of Failure, Shop Testing & Overhaul 10.3 PRD Inspection Intervals, Records & Rupture Disks
11 Chapter 11: Repairs, Alterations, Rerating & Pressure Testing (API 510 & PCC-2)
11.1 Repair vs. Alteration Authorization, Execution & Methods 11.2 PCC-2 Core Welded Repairs: Articles 101, 201, 202, 211 & 212 11.3 PCC-2 Special Welding: Articles 209, 210, 215 & 216 11.4 PCC-2 Excavation, Flange, Exchanger & Test Articles 304, 305, 312, 501 & 502 11.5 Vessel Rerating Requirements & Engineering Calculations 11.6 Pressure Testing: Hydrostatic, Pneumatic & NDE in Lieu of Testing
11.4 PCC-2 Excavation, Flange, Exchanger & Test Articles 304, 305, 312, 501 & 502
Key Takeaways Explain This Topic AI
Article 304 governs flaw excavation and weld repair, including removal boundaries, confirmation that the flaw is gone, weld restoration, and final examination.
Article 305 governs flange repair and conversion; it is the correct listed article for restoring gasket seating, correcting damage, or engineering a flange conversion.
Article 312 covers inspection and repair of shell-and-tube heat exchangers, where tubes, tubesheets, channels, shells, partitions, and joints create interacting leak and pressure boundaries.
Article 501 covers pressure and tightness testing of piping and equipment after repair, with test medium, pressure, temperature, hazards, hold, examination, and acceptance defined by the plan.
Article 502 covers nondestructive examination in lieu of pressure testing for repairs and alterations only when its engineering and examination conditions are satisfied.
Last updated: August 2026
PCC-2 Excavation, Flange, Exchanger, and Test Articles
These five articles cover the back half of a repair workflow: remove a flaw, restore specialized components, and demonstrate integrity. Their official titles provide the safest navigation clues.
1. Article 304 - flaw excavation and weld repair
Excavation removes a crack, lack of fusion, contaminated weld metal, local damage, or other rejectable material before restoration. The plan must define the removal method, limits, minimum remaining wall during excavation, surface shape, confirmation examination, weld procedure, final profile, NDE, and testing.
A crucial hold point occurs after excavation and before welding: verify that the flaw is completely removed. Surface examination is selected for the material, and volumetric examination may be needed for depth or remaining ligament. If a crack remains at the bottom, welding over it hides rather than repairs the defect.
Grinding or machining should produce a smooth weldable cavity without sharp notches. Thermal removal must not introduce uncontrolled hardening or contamination. The engineer reassesses the cavity if removal extends deeper or farther than planned. Restoration then uses a qualified WPS and welder, controlled consumables and heat input, interpass examinations when specified, final contour, final NDE, and records.
2. Article 305 - flange repair and conversion
Article 305, not Article 304, governs flange repair and conversion. Flange problems include gasket-face corrosion, erosion, scratches, warpage, loss of serrations, bolt-hole damage, cracking, reduced thickness, and a need to convert facing or joint configuration.
Inspection records facing type, gasket system, material, class/rating, dimensions, remaining thickness, flatness, surface finish, bolting, alignment, and service. Light damage may be removed by controlled machining if minimum dimensions and rating remain adequate. Deeper loss may need qualified weld buildup and re-machining, or replacement. A conversion changes load path or gasket behavior and therefore needs engineering confirmation rather than a maintenance-only decision.
Final checks confirm dimensions, finish, flatness, alignment, material, NDE of welded areas, and compatibility with gasket and bolting. The repair must not silently reduce flange pressure-temperature capability.
3. Article 312 - shell-and-tube heat exchangers
Heat exchangers contain interacting pressure boundaries. Damage may affect tubes, tubesheet ligaments, tube-to-tubesheet joints, pass partitions, channels, bonnets, floating heads, shells, nozzles, baffles, and supports. A leak may be process-to-utility cross-contamination rather than external.
Start by locating the leaking boundary and mechanism. Tube eddy-current or other tube examination, pressure testing by side, tracer methods, visual examination, UT, and surface NDE may be combined. Repair options can include plugging or sleeving tubes, tube-to-tubesheet repair, tubesheet restoration, partition repair, component replacement, or shell/channel pressure-boundary repair within the applicable method scope.
Evaluate lost heat-transfer area, changed flow, vibration, galvanic compatibility, plugging pattern, differential thermal expansion, and ability to identify future leakage. A mechanically sealed tube may stop a leak yet create a different crevice or thermal problem. Document tube maps and repaired locations.
4. Article 501 - pressure and tightness testing
Article 501 addresses pressure and tightness tests of piping and equipment after repair. A pressure test demonstrates pressure-boundary behavior under a defined load; a tightness test looks for leakage at a pressure and sensitivity suited to the service. They are related but not interchangeable.
The test plan defines boundaries, medium, test and examination pressures, stress ratio where applicable, metal temperature, vents and drains, air removal for hydrotest, overpressure protection, isolation, calibrated gauges, hold time, exclusion zone, leak examination, acceptance, depressurization, drainage/drying, and records. Pneumatic energy creates greater hazard than a comparable hydrostatic test, so engineering and safety controls must reflect stored energy.
5. Article 502 - NDE in lieu of pressure testing
Article 502 supplies a route for qualifying repairs or alterations without a pressure test when the method conditions and engineering basis are met. It is not a blanket statement that NDE is equivalent to every test. The engineer and inspector evaluate repair type, materials, weld access, service, failure consequence, flaw types, examination coverage, personnel/procedure qualification, and ability of selected methods to find credible defects.
A robust plan uses complementary surface and volumetric methods where appropriate, examines the required weld volume and surfaces, controls timing for delayed cracking, defines acceptance, and preserves traceable records. If examination access or reliability cannot meet the article, pressure testing or another repair strategy is required.
6. Article map
- Work Article Navigation clue
- Remove flaw and weld restore 304 Excavation before restoration
- Repair/convert flange 305 Gasket joint and flange rating
- Repair shell-and-tube exchanger 312 Multiple interacting boundaries
- Pressure/tightness test 501 Defined test load and leak check
- Substitute qualified NDE 502 Engineering basis and complete examination
- Exam traps
Article 304 is flaw excavation; Article 305 is flange repair.
Tube plugging decisions require exchanger-system evaluation, not just leak stopping.
A tightness test and a structural pressure test answer different questions.
Article 502 is conditional and must address credible flaws and examination limitations.