11.3 PCC-2 Special Welding: Articles 209, 210, 215 & 216

API 510 Pressure Vessel Inspector Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction, Scope & Certification Requirements

1.1 Exam Structure, Administration & Study Strategy 1.2 API 510 Code Scope, Exclusions & Jurisdictional Boundaries 1.3 Roles, Responsibilities & Inspector Qualification

2 Chapter 2: Inspection Planning, Data Evaluation & Remaining Life

2.1 Corrosion Rates, Remaining Life & Corrosion Allowance Calculations 2.2 Inspection Intervals, On-Stream Inspection & Interval Deferrals 2.3 Condition Monitoring Locations (CMLs) & Data Analysis

3 Chapter 3: Vessel Evaluation, Corrosion Averaging & Fitness-for-Service

3.1 Corrosion Averaging & Minimum Thickness Evaluation 3.2 Pitting Evaluation & Corroded Area Limits 3.3 Fitness-for-Service (API 579-1) & Risk-Based Inspection (API 580)

4 Chapter 4: ASME Section VIII Div 1 Design & Thickness Calculations

4.1 Internal Pressure Design & Cylindrical Shell Calculations 4.2 Ellipsoidal & Hemispherical Head Calculations 4.3 Spherical Shells, Static Head & Vessel MAWP 4.4 Openings, Nozzle Reinforcement & External Pressure Basics

5 Chapter 5: ASME Section VIII Fabrication, Welds & Joint Efficiency

5.1 Weld Joint Categories (UW-3) & Joint Efficiencies (UW-12) 5.2 Radiographic Examination (UW-11, UW-51, UW-52) 5.3 Post-Weld Heat Treatment (PWHT) & Impact Testing (UCS-56, UCS-66)

6 Chapter 6: Welding Inspection & Metallurgy (API 577 & ASME Sec IX)

6.1 Welding Procedures (WPS/PQR) & Essential Variables 6.2 Welder Performance Qualification (WPQ) & Testing 6.3 Welding Processes, Metallurgy & Weld Discontinuities (API 577)

7 Chapter 7: Nondestructive Examination (ASME Section V)

7.1 Radiographic Examination Techniques & Image Quality Indicators (Article 2) 7.2 Ultrasonic Thickness Measurement (Article 23, SE-797) 7.3 ASME Section V Articles 1, 6 & 7: General Requirements, PT & MT

8 Chapter 8: Damage Mechanisms (API RP 571)

8.1 Atmospheric Corrosion & Corrosion Under Insulation 8.2 HTHA, High-Temperature H2/H2S Corrosion & Sulfidation 8.3 Amine, Caustic & Chloride Stress Corrosion Cracking 8.4 Wet H2S Damage, Brittle Fracture & Erosion-Corrosion 8.5 Boiler-Water, Steam-Condensate & Hydrochloric Acid Corrosion 8.6 Caustic Corrosion & Naphthenic Acid Corrosion

9 Chapter 9: Pressure Vessel Inspection Practices (API RP 572 & API RP 578)

9.1 Internal & External Vessel Inspection Practices (API 572) 9.2 Structural Components, Internal Trays, Linings & Skirts 9.3 Material Verification Programs & Positive Material Identification (API 578)

10 Chapter 10: Pressure-Relieving Devices (API RP 576)

10.1 PRD Types, Construction & Operating Principles 10.2 PRD Causes of Failure, Shop Testing & Overhaul 10.3 PRD Inspection Intervals, Records & Rupture Disks

11 Chapter 11: Repairs, Alterations, Rerating & Pressure Testing (API 510 & PCC-2)

11.1 Repair vs. Alteration Authorization, Execution & Methods 11.2 PCC-2 Core Welded Repairs: Articles 101, 201, 202, 211 & 212 11.3 PCC-2 Special Welding: Articles 209, 210, 215 & 216 11.4 PCC-2 Excavation, Flange, Exchanger & Test Articles 304, 305, 312, 501 & 502 11.5 Vessel Rerating Requirements & Engineering Calculations 11.6 Pressure Testing: Hydrostatic, Pneumatic & NDE in Lieu of Testing

11.3 PCC-2 Special Welding: Articles 209, 210, 215 & 216

Key Takeaways Explain This Topic AI

Article 209 covers engineered alternatives to postweld heat treatment; it is not the article for weld overlay or cladding.

Article 210 covers in-service welding onto carbon-steel pressure components or pipelines and requires evaluation of burn-through and hydrogen-cracking risk.

Article 215 addresses repair welding considerations specific to chromium-molybdenum steel pressure vessels, where composition, heat treatment, hardness, and service damage are critical.

Article 216 covers welded hot taps on pressure equipment or piping and integrates mechanical design, welding, isolation contingency, process safety, and operating control.

These articles require a written engineering plan and defined qualification, examination, monitoring, and stop-work criteria; they are not shortcuts for avoiding shutdown.

Last updated: August 2026

PCC-2 Special Welding Repairs

Articles 209, 210, 215, and 216 address repairs where welding itself can threaten the component or operating facility. The exam task is to recognize the distinct risk each article controls and the information needed before work begins.

1. Article 209 - alternatives to PWHT

Postweld heat treatment reduces residual stress, tempers hard microstructures, and supports toughness or service requirements. When local or full PWHT is impractical, Article 209 supplies engineered alternatives within its scope. It does not make PWHT optional whenever a repair team prefers not to perform it.

An alternative plan evaluates base material and P-Number, thickness, service damage, required toughness, hydrogen sensitivity, original heat treatment, construction-code and API 510 requirements, weld geometry, restraint, and service environment. The qualified welding approach may rely on controlled deposition, preheat, bead sequencing, limited heat input, tempering of prior beads, and removal of the final tempering layer as specified by the procedure.

The repair plan defines procedure-qualification tests, thermal controls, hardness limits when applicable, NDE stages, and engineering/inspector hold points. If the material or service falls outside the method limitations, the answer is not to improvise; use PWHT, another repair, or shutdown.

2. Article 210 - in-service welding on carbon steel

In-service welding means the component remains operating or contains process conditions while welding is performed. Two central metallurgical hazards compete:

Burn-through: insufficient remaining wall cannot conduct heat or contain internal pressure during arc exposure.

Hydrogen cracking: rapid cooling plus a hard heat-affected zone, diffusible hydrogen, and restraint can create delayed cracking.

Engineering needs accurate wall thickness, pressure, temperature, contents, flow, material chemistry/carbon equivalent, weld size, heat input, cooling behavior, and consequence of leakage. Flow may cool the wall and reduce burn-through risk while increasing hardening and hydrogen-cracking risk. A successful plan controls both, not just one.

Use verified low-hydrogen consumables, required preheat/interpass controls, a qualified WPS, suitable electrode size and heat input, surface preparation, gas testing, access control, and real-time operating limits. Establish stop criteria for pressure, flow, temperature, wall, leak, or welding deviations. Delayed examination may be needed where delayed cracking is credible.

3. Article 215 - Cr-Mo vessel repair welding

Chromium-molybdenum steels serve at elevated temperature and may develop temper embrittlement, creep damage, hydrogen damage, reheat cracking susceptibility, or degraded toughness depending on grade and history. Repair welding cannot be based only on nominal grade.

Review material verification, operating and thermal history, prior PWHT, weld and heat-affected-zone condition, hardness, damage assessment, hydrogen exposure, creep life where relevant, and the exact Cr-Mo composition. The engineer selects filler metal, preheat, interpass, heat input, controlled cooling, PWHT or qualified alternative, and NDE. Hardness mapping, replication, metallography, or advanced examination may be appropriate when the damage assessment calls for them.

Cr-Mo work requires strict consumable control and temperature monitoring. A superficially sound weld can still leave an unacceptably hard or brittle HAZ, so visual acceptance alone is insufficient.

4. Article 216 - welded hot taps

A hot tap adds a branch connection to operating pressure equipment or piping so a valve and cutting machine can create an opening under controlled conditions. It combines pressure-boundary design, welding on an operating component, cutting, containment, and process hazard.

A plan evaluates component integrity and wall, material, damage mechanisms, pressure and temperature, fluid flammability/reactivity/toxicity, flow, phase, possibility of decomposition or ignition, fitting and branch reinforcement, valve rating, cutter travel, chip retention, leak response, isolation options, and emergency shutdown. Some services or degraded conditions are unsuitable regardless of production benefit.

Sequence matters: verify the component and location, install and examine the fitting weld, pressure/leak test the assembly as approved, mount valve and machine, confirm travel, cut and retain the coupon, retract the cutter, close and verify the valve, then remove equipment under the procedure. Each stage has a hold point and contingency.

5. Comparison

• Article Controlled risk Key evidence
• 209 Required heat-treatment function Material, service, procedure qualification, thermal controls
• 210 Welding on operating carbon steel Wall, process, burn-through and cooling/hydrogen analysis
• 215 Cr-Mo metallurgical vulnerability Exact grade, history, damage, hardness/toughness, PWHT plan
• 216 Operating hot-tap system hazard Mechanical design, process safety, welding, valve/cutter contingency
• Exam traps

Article 209 is the PWHT-alternative article; Article 211 covers overlay/clad restoration.

More flow is not simply safer during in-service welding: it can reduce burn-through and worsen HAZ hardening.

A hot tap is not merely a nozzle weld; it is an integrated operating procedure.

No special welding article eliminates API 510 authorization or jurisdiction.