Study guide

6.3 Welding Processes, Metallurgy & Weld Discontinuities (API 577)

API 510 Pressure Vessel Inspector Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction, Scope & Certification Requirements

1.1 Exam Structure, Administration & Study Strategy 1.2 API 510 Code Scope, Exclusions & Jurisdictional Boundaries 1.3 Roles, Responsibilities & Inspector Qualification

2 Chapter 2: Inspection Planning, Data Evaluation & Remaining Life

2.1 Corrosion Rates, Remaining Life & Corrosion Allowance Calculations 2.2 Inspection Intervals, On-Stream Inspection & Interval Deferrals 2.3 Condition Monitoring Locations (CMLs) & Data Analysis

3 Chapter 3: Vessel Evaluation, Corrosion Averaging & Fitness-for-Service

3.1 Corrosion Averaging & Minimum Thickness Evaluation 3.2 Pitting Evaluation & Corroded Area Limits 3.3 Fitness-for-Service (API 579-1) & Risk-Based Inspection (API 580)

4 Chapter 4: ASME Section VIII Div 1 Design & Thickness Calculations

4.1 Internal Pressure Design & Cylindrical Shell Calculations 4.2 Ellipsoidal & Hemispherical Head Calculations 4.3 Spherical Shells, Static Head & Vessel MAWP 4.4 Openings, Nozzle Reinforcement & External Pressure Basics

5 Chapter 5: ASME Section VIII Fabrication, Welds & Joint Efficiency

5.1 Weld Joint Categories (UW-3) & Joint Efficiencies (UW-12) 5.2 Radiographic Examination (UW-11, UW-51, UW-52) 5.3 Post-Weld Heat Treatment (PWHT) & Impact Testing (UCS-56, UCS-66)

6 Chapter 6: Welding Inspection & Metallurgy (API 577 & ASME Sec IX)

6.1 Welding Procedures (WPS/PQR) & Essential Variables 6.2 Welder Performance Qualification (WPQ) & Testing 6.3 Welding Processes, Metallurgy & Weld Discontinuities (API 577)

7 Chapter 7: Nondestructive Examination (ASME Section V)

7.1 Radiographic Examination Techniques & Image Quality Indicators (Article 2) 7.2 Ultrasonic Thickness Measurement (Article 23, SE-797) 7.3 ASME Section V Articles 1, 6 & 7: General Requirements, PT & MT

8 Chapter 8: Damage Mechanisms (API RP 571)

8.1 Atmospheric Corrosion & Corrosion Under Insulation 8.2 HTHA, High-Temperature H2/H2S Corrosion & Sulfidation 8.3 Amine, Caustic & Chloride Stress Corrosion Cracking 8.4 Wet H2S Damage, Brittle Fracture & Erosion-Corrosion 8.5 Boiler-Water, Steam-Condensate & Hydrochloric Acid Corrosion 8.6 Caustic Corrosion & Naphthenic Acid Corrosion

9 Chapter 9: Pressure Vessel Inspection Practices (API RP 572 & API RP 578)

9.1 Internal & External Vessel Inspection Practices (API 572) 9.2 Structural Components, Internal Trays, Linings & Skirts 9.3 Material Verification Programs & Positive Material Identification (API 578)

10 Chapter 10: Pressure-Relieving Devices (API RP 576)

10.1 PRD Types, Construction & Operating Principles 10.2 PRD Causes of Failure, Shop Testing & Overhaul 10.3 PRD Inspection Intervals, Records & Rupture Disks

11 Chapter 11: Repairs, Alterations, Rerating & Pressure Testing (API 510 & PCC-2)

11.1 Repair vs. Alteration Authorization, Execution & Methods 11.2 PCC-2 Core Welded Repairs: Articles 101, 201, 202, 211 & 212 11.3 PCC-2 Special Welding: Articles 209, 210, 215 & 216 11.4 PCC-2 Excavation, Flange, Exchanger & Test Articles 304, 305, 312, 501 & 502 11.5 Vessel Rerating Requirements & Engineering Calculations 11.6 Pressure Testing: Hydrostatic, Pneumatic & NDE in Lieu of Testing

6.3 Welding Processes, Metallurgy & Weld Discontinuities (API 577)

Key Takeaways Explain This Topic AI

API 577 covers five primary welding processes used in refinery and vessel fabrication: Shielded Metal Arc Welding (SMAW), Gas Tungsten Arc Welding (GTAW), Gas Metal Arc Welding (GMAW), Flux-Cored Arc Welding (FCAW), and Submerged Arc Welding (SAW), each with distinct shielding, deposition, and defect profiles.

AWS electrode classifications codify tensile strength, welding position, coating chemistry, and operating current (e.g., E7018 denotes 70 ksi minimum tensile strength, all-position welding except vertical-down, low-hydrogen iron powder flux coating, DCEP/AC current).

Carbon Equivalent (CE = %C + %Mn/6 + (%Cr+%Mo+%V)/5 + (%Ni+%Cu)/15) measures steel hardenability; CE values exceeding 0.43 to 0.45 significantly elevate the risk of Hydrogen-Assisted Cracking (HAC) and mandate preheat, interpass temperature controls, and low-hydrogen consumables.

Weld discontinuities are categorized as planar (cracks, lack of fusion, incomplete penetration) or volumetric (porosity, slag inclusions); planar flaws create sharp stress risers and are the most critical rejectable defects in pressure equipment.

Austenitic stainless steel weldments (300 series) require a controlled Ferrite Number (typically 3 to 10 FN, or 5% to 8% delta ferrite) to prevent hot cracking and microfissuring during solidification, while avoiding excess ferrite that can transform to brittle sigma phase at elevated operating temperatures.

Last updated: August 2026

Welding Processes, Metallurgy & Weld Discontinuities (API 577)

Welding inspection in the refining, chemical, and process industries demands a deep foundation in both mechanical execution and physical metallurgy. An API 510 Inspector must not only detect flaws during visual and nondestructive examinations, but also understand the metallurgical root causes—such as phase transformations, thermal stresses, hydrogen embrittlement, and solidification dynamics—that produce those flaws.

API Recommended Practice 577 ( Welding Processes, Inspection, and Metallurgy ) provides practical guidance on welding operations, filler metal classifications, metallurgical phenomena, and defect acceptance criteria.

1. Industrial Welding Processes & Operating Characteristics (API 577 Section 5)

Five primary electric arc welding processes dominate pressure vessel fabrication, alteration, and repair: +-----------------------------------------------------------------------------+

  • | PRIMARY PRESSURE VESSEL WELDING PROCESSES |
  • | |
  • | [SMAW] "Stick" Welding ---> Flux-coated consumable electrode |
  • | [GTAW] "TIG" Welding ---> Non-consumable tungsten + inert shield gas|
  • | [GMAW] "MIG/MAG" Welding ---> Continuous solid wire + shielding gas |
  • | [FCAW] Flux-Cored Arc ---> Continuous tubular wire with flux core |
  • | [SAW] Submerged Arc ---> Continuous bare wire under granular flux |
  • +-----------------------------------------------------------------------------+
  • Comparative Analysis of Welding Processes

Process Shielding Method Advantages Limitations Common Discontinuities

SMAW (Shielded Metal Arc) Decomposition of flux coating generating gas envelope and slag cover. Highly portable, versatile, low equipment cost, excellent for field repairs and confined spaces. Low deposition rate, high operator fatigue, frequent stop/starts, slag cleaning required between passes. Slag inclusions, start/stop porosity, undercut, lack of fusion.

GTAW (Gas Tungsten Arc) Externally supplied inert gas (100% Argon, Helium, or Ar-He mixtures). Highest weld quality, precise heat control, exceptional root pass integrity, no slag formation. Very low deposition rate, expensive equipment, highly sensitive to wind/drafts in field welding. Tungsten inclusions, porosity from loss of gas shield, lack of fusion.

GMAW (Gas Metal Arc) Externally supplied gas ( C O 2 CO_2 C O 2 ​ , Argon- C O 2 CO_2 C O 2 ​ , Ar- O 2 O_2 O 2 ​ mixtures). Continuous wire feed, high deposition, no slag, easily automated, clean weld deposit. Equipment complexity, wind sensitivity, short-circuit mode (GMAW-S) prone to severe cold lap. Lack of side-wall fusion (cold lap in GMAW-S), porosity, undercut.

FCAW (Flux-Cored Arc) Internal flux core, with optional external gas shielding (FCAW-G vs. FCAW-S). High deposition rates, deep penetration, good field tolerance, high travel speeds. Generates heavy slag requiring cleaning, produces copious smoke/fumes, wire storage sensitivity. Slag entrapment, wormhole porosity, excessive undercut, cracking.

SAW (Submerged Arc) Blanketing layer of granular fusible mineral flux submerged over arc. Extremely high deposition rates ( > 15 lb/hr > 15\text{ lb/hr} > 15 lb/hr ), deep penetration, excellent mechanicals. Limited strictly to flat (1G) and horizontal (2F) positions; high heat input coarsens HAZ grains. Solidification cracking (centerline), slag entrapment, burn-through.

GMAW Modes of Metal Transfer

Short-Circuiting Transfer (GMAW-S): Low heat input, small weld pool; electrode touches work 20–200 times/sec. Excellent for thin sheet and root passes, but carries an extreme risk of lack of side-wall fusion ("cold lap") on thick vessel materials.

Globular Transfer: Larger droplets than wire diameter fall under gravity; produces high spatter and rough weld appearance.

Spray Transfer: High current and voltage with Argon-rich shielding ( > 80 % Ar > 80\%\text{ Ar} > 80% Ar ); fine droplets sprayed across arc. High deposition, excellent fusion, limited to flat/horizontal positions.

Pulsed Spray (GMAW-P): Current pulses between low background level and high peak spray level. Allows all-position welding with spray-quality fusion and low heat input.

2. AWS Filler Metal & Electrode Classification Nomenclature

American Welding Society (AWS) specifications classify electrodes and filler metals with standardized alphanumeric designations: +-----------------------------------------------------------------------------+

  • | SMAW ELECTRODE DESIGNATION SYSTEM (AWS A5.1 / A5.5) |
  • | |
  • | E 70 1 8 - H4 R - 1 |
  • | | | | | | | | |
  • | Electrode | Position | Diffusible | Improved Low-Temp |
  • | | | Hydrogen | Toughness (-50°F) |
  • | Min Tensile Flux Coating & (<= 4 mL/100g) |
  • | (70 ksi) Current/Polarity Moisture Resistant |
  • | (Low Hydrogen, DCEP) |
  • +-----------------------------------------------------------------------------+
  • Breakdown of Electrode Classifications

Tensile Strength Designator (First 2 or 3 digits): Indicates minimum tensile strength in ksi (e.g., 70 = 70 , 000 psi 70,000\text{ psi} 70 , 000 psi , 80 = 80 , 000 psi 80,000\text{ psi} 80 , 000 psi , 110 = 110 , 000 psi 110,000\text{ psi} 110 , 000 psi ). For stainless steel (e.g., E308 , E316 ), the 3 digits represent the AISI alloy grade.

Position Designator (Third or Fourth digit):

1 : All positions (flat, horizontal, vertical, overhead).

2 : Flat position and horizontal fillet welds only.

4 : Vertical-down progression and flat/horizontal (specialized electrodes).

Coating & Current Type (Last digit):

0 : High cellulose sodium (DCEP, e.g., E6010 — deep penetration).

1 : High cellulose potassium (AC/DCEP, e.g., E6011).

5 : Low hydrogen sodium (DCEP, e.g., E7015).

6 : Low hydrogen potassium (AC/DCEP, e.g., E7016).

8 : Low hydrogen iron powder (AC/DCEP, e.g., E7018 — high deposition, crack resistant).

GTAW/GMAW Solid Wire Designation (e.g., ER70S-6):

ER : Electrode or Rod (usable for GMAW wire or GTAW cut rod).

70 : Minimum tensile strength ( 70 ksi 70\text{ ksi} 70 ksi ).

S : Solid bare wire.

6 : Chemical composition with high silicon/manganese deoxidizers for welding over mill scale and light rust.

3. Welding Metallurgy: Heat-Affected Zone (HAZ) & Microstructure

When steel is welded, the localized thermal cycle creates dramatic metallurgical transformations across three distinct regions: +-----------------------------------------------------------------------------+

  • | WELD JOINT METALLURGICAL ZONES |
  • | |
  • | +-------------+--------------+------------------+---------------------+ |
  • | | WELD METAL | FUSION LINE | HEAT-AFFECTED | UNTREATED BASE METAL| |
  • | | (Cast Solid)| (Bond Line) | ZONE (HAZ) | (Original Mill Mtl) | |
  • | +-------------+--------------+------------------+---------------------+ |
  • | | | | | |
  • | v v v v |
  • | As-cast Maximum Microstructural Unaltered base |
  • | dendritic thermal zones: Coarse-Grain grain structure |
  • | structure gradient Fine-Grain, Inter- and mechanicals |
  • | critical, Subcritical |
  • +-----------------------------------------------------------------------------+
  • The Sub-Zones of the Heat-Affected Zone (HAZ)

Coarse-Grained HAZ (CGHAZ): Adjacent to the fusion line; heated above 2000 ∘ F ( 1100 ∘ C ) 2000^\circ\text{F} (1100^\circ\text{C}) 200 0 ∘ F ( 110 0 ∘ C ) . Austenite grains grow excessively large. Upon rapid cooling, large grains transform into hard martensite or bainite, resulting in high hardness, low ductility, and reduced notch toughness (most susceptible to cracking).

Fine-Grained HAZ (FGHAZ): Heated just above the A c 3 Ac_3 A c 3 ​ upper transformation temperature ( 1650 ∘ F / 900 ∘ C 1650^\circ\text{F} / 900^\circ\text{C} 165 0 ∘ F /90 0 ∘ C ). Undergoes grain refinement (normalization), yielding excellent toughness and strength.

Intercritical HAZ (ICHAZ): Heated between A c 1 Ac_1 A c 1 ​ and A c 3 Ac_3 A c 3 ​ ( 1350 ∘ F to 1650 ∘ F 1350^\circ\text{F} \text{ to } 1650^\circ\text{F} 135 0 ∘ F to 165 0 ∘ F ). Incomplete transformation creates mixed microstructures with localized soft or hard zones.

Subcritical HAZ (SCHAZ): Heated below A c 1 Ac_1 A c 1 ​ ( < 1350 ∘ F < 1350^\circ\text{F} < 135 0 ∘ F ). No phase transformation; undergoes minor tempering or stress relief.

  • 4. Carbon Equivalent ( C E CE CE ), Hydrogen Cracking Triad & Preheat Control
  • The Hydrogen-Assisted Cracking (HAC) Triad

Hydrogen-Assisted Cracking (also called cold cracking, delayed cracking, or underbead cracking) is the single most hazardous defect mechanism in carbon and low-alloy steel welding. It requires the simultaneous convergence of three critical factors: +-----------------------------------------------------------------------------+

  • | HYDROGEN CRACKING CRITICAL TRIAD |
  • | |
  • | [HARD, SUSCEPTIBLE MICROSTRUCTURE] |
  • | (High CE, Martensite in CGHAZ) |
  • | /\\ |
  • | / \\ |
  • | / \\ |
  • | / \\ |
  • | [DIFFUSIBLE HYDROGEN] <------------- [HIGH RESIDUAL TENSILE STRESS] |
  • | (Moisture in flux, oil, (Restraint, joint geometry, |
  • | grease, humid atmosphere) weld shrinkage stresses) |
  • +-----------------------------------------------------------------------------+
  • Carbon Equivalent ( C E CE CE ) Formula (API 577 Section 10.3)

The Carbon Equivalent quantifies the hardenability of steel by converting the combined effect of various alloying elements into an equivalent percentage of carbon: C E = %C + %Mn 6 + %Cr + %Mo + %V 5 + %Ni + %Cu 15 CE = \text{\%C} + \frac{\text{\%Mn}}{6} + \frac{\text{\%Cr} + \text{\%Mo} + \text{\%V}}{5} + \frac{\text{\%Ni} + \text{\%Cu}}{15} CE = %C + 6 %Mn ​ + 5 %Cr + %Mo + %V ​ + 15 %Ni + %Cu ​

Hardenability & Preheat Threshold Guidelines

Carbon Equivalent ( C E CE CE ) Range Weldability Classification Cracking Susceptibility Mandatory Preventive Protocols

C E ≤ 0.35 CE \le 0.35 CE ≤ 0.35 Excellent Weldability Low Risk Standard welding procedures; preheat generally not required unless heavy section ( T > 1 in. T > 1\text{ in.} T > 1 in. ).

0.35 < C E ≤ 0.43 0.35 < CE \le 0.43 0.35 < CE ≤ 0.43 Moderate Weldability Medium Risk Preheat of 150 ∘ F to 250 ∘ F ( 65 ∘ C to 120 ∘ C ) 150^\circ\text{F} \text{ to } 250^\circ\text{F} (65^\circ\text{C} \text{ to } 120^\circ\text{C}) 15 0 ∘ F to 25 0 ∘ F ( 6 5 ∘ C to 12 0 ∘ C ) recommended; low-hydrogen electrodes (F-4) standard.

C E > 0.43 to 0.45 CE > 0.43 \text{ to } 0.45 CE > 0.43 to 0.45 High Hardenability High Cracking Risk Mandatory preheat ( 250 ∘ F to 400 ∘ F 250^\circ\text{F} \text{ to } 400^\circ\text{F} 25 0 ∘ F to 40 0 ∘ F ), strict interpass temperature control, H4 low-hydrogen consumables, post-heat bake-out ( 400 ∘ F for 2 hours 400^\circ\text{F} \text{ for } 2\text{ hours} 40 0 ∘ F for 2 hours ) to diffuse hydrogen.

5. Post-Weld Heat Treatment (PWHT) Principles & Hardness Controls

Post-Weld Heat Treatment (PWHT) , governed by ASME Section VIII Div 1 paragraph UCS-56 and API 577 Section 10.6, involves heating the completed weldment uniformly to a subcritical temperature (typically 1100 ∘ F to 1250 ∘ F / 590 ∘ C to 675 ∘ C 1100^\circ\text{F} \text{ to } 1250^\circ\text{F} / 590^\circ\text{C} \text{ to } 675^\circ\text{C} 110 0 ∘ F to 125 0 ∘ F /59 0 ∘ C to 67 5 ∘ C for P-1 carbon steels) and holding for a specified duration (typically 1 hr per inch 1\text{ hr per inch} 1 hr per inch of thickness).

Primary Metallurgical Benefits of PWHT:

Residual Stress Relief: Thermal relaxation reduces peak weld residual stresses (which can reach base metal yield strength) down to 15 % to 20 % 15\% \text{ to } 20\% 15% to 20% of original levels.

Tempering of Hard Microstructures: Tempers hard martensite in the coarse-grained HAZ into tempered martensite, restoring ductility and impact toughness.

Hydrogen Bake-Out: Accelerates the diffusion of trapped hydrogen out of the weldment before cracking can initiate.

Dimensional Stability: Minimizes distortion during subsequent machining or service.

Hardness Limits for Environmental Cracking Prevention

In refinery wet H 2 S H_2S H 2 ​ S (sour) and caustic service, high HAZ hardness drastically accelerates sulfide stress cracking (SSC) and stress corrosion cracking (SCC).

NACE MR0175 / SP0296 and API RP 582 establish a maximum hardness limit of 200 HBW (or 248 HV / 22 HRC) for carbon steel welds in sour service.

6. Weld Discontinuities, Flaws, and NDE Inspection Selection (API 577 Section 9)

A discontinuity is any interruption in the normal physical structure of a weldment. A discontinuity becomes a defect only when its size, shape, or orientation exceeds the specific acceptance criteria of the applicable construction or in-service code. +-----------------------------------------------------------------------------+

  • | PLANAR VS. VOLUMETRIC WELD DISCONTINUITIES |
  • | |
  • | [PLANAR DISCONTINUITIES (CRITICAL)] [VOLUMETRIC DISCONTINUITIES] |
  • | - Sharp crack-like tip geometry - Rounded, three-dimensional |
  • | - Severe stress concentration risers - Lower stress concentration |
  • | - Cracks (Hot, Cold, Lamellar, Crater) - Porosity (Spherical, Cluster)|
  • | - Lack of Fusion (LOF / Cold Lap) - Slag Inclusions |
  • | - Incomplete Penetration (LOP) - Tungsten Inclusions |
  • | - Detected best by UT / PAUT / MT / PT - Detected best by RT |
  • +-----------------------------------------------------------------------------+
  • Comprehensive Discontinuity & NDE Selection Matrix

Discontinuity Type Physical Morphology Primary Root Causes Optimal NDE Inspection Method

Cracks (Cold / HAC) Longitudinal or transverse sharp cracks in HAZ or weld metal. High CE, presence of hydrogen, high residual stress, lack of preheat. MT (ferromagnetic surface), PT (non-mag surface), UT/PAUT (volumetric planar).

Cracks (Hot / Solidification) Centerline longitudinal crack along weld bead center. Low melting point impurities (S, P), high depth-to-width bead ratio, excessive heat input. VT, PT, MT, UT/PAUT .

Lack of Fusion (LOF) Planar separation between weld metal and base metal or adjacent passes. Improper gun angle, low heat input, fast travel speed, oxide scale; severe in GMAW-S. UT / PAUT (highly reliable); RT is often blind to tight planar side-wall LOF.

Incomplete Penetration (LOP) Planar void at joint root where weld metal failed to penetrate full thickness. Low welding current, travel speed too fast, root face too large, root gap too small. RT (appears as dark straight line in root), UT/PAUT , VT (if root accessible).

Porosity (Gas Pockets) Rounded or elongated spherical cavities ( N 2 , H 2 , C O N_2, H_2, CO N 2 ​ , H 2 ​ , CO ). Wet electrodes, damp flux, wind blowing shielding gas away, grease/oil on joint bevel. RT (clear rounded dark spots), UT (attenuation/scatter).

Slag Inclusions Non-metallic solid entrapped flux residues between weld beads. Inadequate interpass slag cleaning, improper electrode angle, tight deep groove. RT (dark irregular jagged shapes), UT .

Undercut Groove melted into base metal at weld toe not filled by weld metal. Excessive arc voltage/current, travel speed too fast, incorrect electrode angle. VT (depth gauge), MT/PT (stress riser inspection).

Burn-Through Complete localized collapse of weld pool blowing a hole through root. Excessive current, excessive root gap, travel speed too slow on thin-wall joints. VT (visual inspection inside/outside), RT .

7. Delta Ferrite & Ferrite Number (FN) in Austenitic Stainless Steel Welds

When welding austenitic stainless steels (such as AISI Types 304, 304L, 316, 316L, 321, 347): +-----------------------------------------------------------------------------+

  • | AUSTENITIC STAINLESS STEEL FERRITE BALANCE |
  • | |
  • | [TOO LOW FERRITE (< 3 FN)] [OPTIMAL BALANCE (3 - 10 FN)] |
  • | - Fully austenitic solidification - Solidifies as primary delta |
  • | - Segregation of P and S to boundaries ferrite |
  • | - EXTREME HOT CRACKING / MICROFISSURES - Impurities dissolve in ferrite |
  • | - EXCELLENT CRACK RESISTANCE |
  • | |
  • | [TOO HIGH FERRITE (> 10 - 12 FN)] |
  • | - High-temperature service (1000°F - 1500°F) transforms ferrite to brittle |
  • | SIGMA PHASE (sigma embrittlement) |
  • | - Degrades low-temperature cryogenic toughness and specific acid corrosion|
  • +-----------------------------------------------------------------------------+

Ferrite Control Guidelines:

Prevention of Hot Cracking: Austenitic stainless weld filler metals (e.g., E308L, ER316L) are intentionally alloyed with a slightly higher chromium-to-nickel ratio to ensure that 3 % to 10 % 3\% \text{ to } 10\% 3% to 10% delta ferrite (3 to 10 FN) forms in the as-deposited microstructure. Delta ferrite dissolves low-melting phosphorus and sulfur impurities, preventing them from forming liquid films along grain boundaries during cooling.

Measurement of Ferrite: Measured using magnetic instruments (Ferritescope) or calculated via the DeLong, Schaeffler, or WRC-1992 constitution diagrams using Chromium Equivalent ( C r eq Cr_{\text{eq}} C r eq ​ ) and Nickel Equivalent ( N i eq Ni_{\text{eq}} N i eq ​ ).

8. Common Exam Traps & Pitfalls

Warning

Trap 1: GMAW-S and Radiographic Examination: Questions often ask why GMAW short-circuiting mode (GMAW-S) cannot be qualified for welder testing via Radiography alone. Reason: GMAW-S is notorious for cold lap (lack of side-wall fusion). Because cold lap produces zero gap and no significant density change, RT frequently misses it . Ultrasonic testing (UT) or mechanical guided bend tests are required.

Important

Trap 2: Coarse-Grained HAZ vs. Weld Metal Hardness: When hydrogen-assisted cracking occurs, it almost always initiates in the Coarse-Grained Heat-Affected Zone (CGHAZ) rather than the weld metal because the CGHAZ undergoes extreme grain growth followed by rapid quenching into hard martensite.

Tip

Trap 3: Austenitic Stainless Steel Preheat Myth: Carbon and low-alloy steels require preheat to prevent hardening and hydrogen cracking. In contrast, austenitic stainless steels (P-8) DO NOT undergo phase transformation to martensite and must NEVER be preheated . Applying high preheat or excessive interpass temperature ( > 350 ∘ F > 350^\circ\text{F} > 35 0 ∘ F ) to austenitic stainless steel increases distortion, promotes carbide precipitation (sensitization), and elevates hot cracking risk.

Loading diagram... Welding Discontinuity Classification & NDE Method Selection