Study guide
4.2 Flange Ratings & P-T Limits (ASME B16.5)
API 570 Piping Inspector Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Piping Inspection Planning & Circuits
1.1 Inspection Planning, History, and Safety 1.2 Piping Circuitization and Circuit Design 1.3 Condition Monitoring Locations (CMLs) & Coverage
2 Chapter 2: Inspection Intervals & Extent of Inspection
2.1 Piping Classifications (Classes 1, 2, 3, and 4) 2.2 Thickness Inspection Intervals (Half-Life & Visual Rules) 2.3 Owner-User QA and Roles (Inspector, Engineer, Examiner)
3 Chapter 3: Calculations & Remaining Life
3.1 Corrosion Rates (Short-Term, Long-Term, and Initial Estimates) 3.2 Remaining Life and Retirement Thickness Calculations 3.3 MAWP Calculations for In-Service Piping
4 Chapter 4: ASME Codes for Piping Design
4.1 Wall Thickness Calculations for Pipe under Pressure (ASME B31.3) 4.2 Flange Ratings & P-T Limits (ASME B16.5) 4.3 Pressure & Leak Testing Rules (Hydrostatic vs. Pneumatic) 4.4 Weld Joint Quality Factors (Ej) and Casting Quality Factors (Ec) 4.5 Impact Testing, MDMT Exemption, and Charpy Requirements 4.6 Thermal Expansion Calculations (ASME B31.3 Appendix C) 4.7 Minimum Required Thickness of Permanent Blanks
5 Chapter 5: Nondestructive Examination (NDE)
5.1 Visual, Penetrant, and Magnetic Testing (VT, PT, MT) per ASME Sec V 5.2 Radiographic and Ultrasonic Testing (RT, UT) per ASME Sec V 5.3 Examiner Selection, Calibrations, and Acceptance Standards 5.4 Leak Testing per ASME Section V Article 10
6 Chapter 6: Welding Procedures & Qualifications
6.1 Reviewing WPS and PQR per ASME Section IX 6.2 Welder Performance Qualification (WPQ) and Limits 6.3 Preheating & PWHT Rules and Controls 6.4 Welding Processes, Inspection, and Metallurgy (API RP 577)
7 Chapter 7: Valves, Components, Materials & PRDs
7.1 Piping Components and Valves (API RP 574) 7.2 Positive Material Identification (PMI) (API RP 578) 7.3 Pressure Relieving Devices (PRDs) (API RP 576)
8 Chapter 8: Damage Mechanisms & Repairs
8.1 Corrosion Under Insulation (CUI) and Ambient Mechanisms 8.2 Process-Driven Damage Mechanisms (API RP 571) 8.3 Temporary and Permanent Repair Methods (ASME PCC-2 & API 570) 8.4 Soil Corrosion, Galvanic Corrosion, and Boiler Water Condensate Corrosion 8.5 Piping Rerating and Alterations (API 570) 8.6 Inspection Records, Reports, and Documentation 8.7 Amine/Caustic SCC, HCl, Sour Water, and MIC (API RP 571)
4.2 Flange Ratings & P-T Limits (ASME B16.5)
Key Takeaways Explain This Topic AI
ASME B16.5 governs flange dimensions and pressure-temperature limits for NPS 1/2 through NPS 24.
Flange pressure-temperature ratings are determined dynamically by design temperature and material group.
Raised Face (RF) flanges concentrate bolt load, Flat Face (FF) prevents cracking cast iron casing, and Ring Joint (RTJ) is for high-pressure/temp.
Flange alignment checks require parallelism within 0.06 inches and bolt hole alignment within 0.125 inches.
Flange face radial scratches/gouges must be measured and evaluated against strict ASME B16.5 limits.
Last updated: July 2026
4.2 Flange Ratings & P-T Limits (ASME B16.5)
In piping systems, flanges serve as the mechanical joints that connect pipe sections, valves, pumps, and vessels. Because flanged joints are held together by bolt tension and sealed with gaskets, they are often the most vulnerable points for process leaks. ASME B16.5 is the construction standard that governs Pipe Flanges and Flanged Fittings (NPS 1/2 through NPS 24). As an API 570 inspector, you must understand how flange pressure-temperature (P-T) ratings are established, how material classifications affect these limits, and the critical inspection criteria for flange faces, bolt alignment, and gasket seating.
Flange Pressure Classes and Material Groups
ASME B16.5 classifies flanges into seven pressure ratings (often called "classes"): 150, 300, 400, 600, 900, 1500, and 2500 . These classes represent nominal pressure limits, but the actual maximum allowable working pressure of a flange is not constant. It is a dynamic limit determined by two factors:
The Design Temperature of the system.
The Material Group of the flange.
ASME B16.5 groups materials with similar metallurgical and strength properties into Material Groups . For example:
Material Group 1.1 : Contains common carbon steels, such as ASTM A105 (forgings), ASTM A106 Grade B (pipe, when forged/machined), and ASTM A350 LF2 (low-temperature service).
Material Group 2.2 : Contains standard austenitic stainless steels, such as ASTM A182 Grade F316/F316H (forgings) and ASTM A312 Grade TP316 (pipe).
For each material group, ASME B16.5 Table 2 provides a listing of the maximum allowable working gauge pressure (in psi or bar) at temperatures ranging from − 20 ∘ F -20^\circ\text{F} − 2 0 ∘ F up to 1500 ∘ F 1500^\circ\text{F} 150 0 ∘ F .
Temperature-Pressure Relationship
As the operating temperature of a piping system increases, the yield strength of the flange metal decreases. Consequently, the allowable pressure rating of the flange drops. The following table illustrates this relationship for Material Group 1.1 (Carbon Steel) flanges:
- Temperature ( ∘ F ^\circ\text{F} ∘ F ) Class 150 (psig) Class 300 (psig) Class 600 (psig) Class 900 (psig)
- 20 to 100 285 740 1,480 2,220
- 200 260 680 1,360 2,035
- 400 200 635 1,265 1,900
- 600 140 570 1,135 1,705
- 800 80 410 825 1,235
- 900 (creep range) 50 170 345 515
Note for the Exam: Carbon steel is subject to graphitization and severe creep above 800 ∘ F 800^\circ\text{F} 80 0 ∘ F . Notice the dramatic drop in the rating of Class 300 flanges from 410 psig 410\text{ psig} 410 psig at 800 ∘ F 800^\circ\text{F} 80 0 ∘ F down to 170 psig 170\text{ psig} 170 psig at 900 ∘ F 900^\circ\text{F} 90 0 ∘ F . Inspectors must verify that the operating conditions of the piping system never exceed these rated limits.
Step-by-Step Worked Example: Flange Rating Verification
Let's walk through a concrete engineering check to determine if a flange is suitable for a given set of design conditions:
Design Conditions :
- Design Pressure : 580 psig 580\text{ psig} 580 psig
- Design Temperature : 600 ∘ F 600^\circ\text{F} 60 0 ∘ F
- Flange Material : ASTM A105 Carbon Steel
- Proposed Flange Rating : Class 300
Step 1: Identify the Material Group Looking at the material specification index of ASME B16.5, ASTM A105 is classified under Material Group 1.1 .
Step 2: Locate the Pressure-Temperature Rating Table Find Table 2-1.1 in ASME B16.5, which outlines the P-T ratings for Material Group 1.1.
Step 3: Determine the Flange Rating at the Design Temperature Locate the temperature line for 600 ∘ F 600^\circ\text{F} 60 0 ∘ F and look across to the column for Class 300:
The maximum allowable working gauge pressure for Class 300 at 600 ∘ F 600^\circ\text{F} 60 0 ∘ F is 570 psig .
- Step 4: Compare the Flange Rating with the System Design Pressure
- Maximum Allowable Flange Pressure = 570 psig 570\text{ psig} 570 psig
- System Design Pressure = 580 psig 580\text{ psig} 580 psig
Result: The design pressure ( 580 psig 580\text{ psig} 580 psig ) exceeds the flange's limit ( 570 psig 570\text{ psig} 570 psig ) at this temperature.
Conclusion :
A Class 300 flange cannot be used for these design conditions. The piping engineer must specify a higher class. Checking Class 600 in the same table:
Maximum Allowable Pressure for Class 600 at 600 ∘ F 600^\circ\text{F} 60 0 ∘ F is 1,135 psig .
Since 1 , 135 psig ≥ 580 psig 1,135\text{ psig} \ge 580\text{ psig} 1 , 135 psig ≥ 580 psig , a Class 600 flange must be specified.
Flange Face Configurations
The design of the mating surfaces (flange faces) dictates the type of gasket used and the pressure the joint can contain:
Raised Face (RF) : The most common configuration in process plants. The gasket surface is raised above the bolting circle by 0.06 inches (1.6 mm) for Class 150 and Class 300 flanges, and by 0.25 inches (6.4 mm) for Class 400 and higher. This concentrates bolt clamping force onto a smaller gasket area, creating a highly effective seal.
Flat Face (FF) : The mating surface is completely flat, without a raised portion. Flat Face flanges are typically used when joining steel flanges to cast iron flanges (such as on pump casings or valves). Because cast iron is brittle, torqueing a Raised Face steel flange against a cast iron flange creates a bending moment that can easily crack the cast iron flange. Mating two Flat Face flanges allows the gasket pressure to distribute uniformly.
Ring-Type Joint (RTJ) : Primarily used in high-pressure and high-temperature services (Class 600 and above). The flange face has a machined groove that accommodates a solid metal ring gasket (usually oval or octagonal). As the bolts are tightened, the metal ring deforms into the groove, creating a metal-to-metal seal.
Flange Alignment and Bolt Inspection Criteria
An inspector must verify that flanges are properly aligned before bolting. Misalignment introduces high localized bending stresses in the pipe wall and bolts, which can lead to stress corrosion cracking or joint fatigue.
Key alignment parameters include:
Parallelism : Flange faces must be parallel. When measured, the variation in the distance between the flange faces must not exceed 0.06 inches (1.6 mm) across the diameter.
Flange Gap : The gap between the flange faces must be uniform and just wide enough to slide the gasket in without damage, but close enough that the bolts do not have to stretch the piping to close the joint.
Bolt Hole Offset (Rotational Alignment) : Bolt holes must align within a maximum offset of 0.125 inches (3 mm) . This ensures that bolts can pass through without binding or bending.
Bolt Length and Thread Engagement : When fully tightened, heavy hex bolts or heavy hex alloy steel studs (typically ASTM A193 Grade B7 with heavy hex nuts ASTM A194 Grade 2H ) must extend so that the bolt threads are flush with the nut face as a minimum. Ideally, the bolt should extend 1 to 2 threads beyond the nut.
Flange Face Imperfections
The sealing capability of a flange relies on the integrity of the serrated finish on the flange face. Radial scratches, gouges, or corrosion pits that cross the gasket seating area can create tiny pathways for process fluid to escape.
ASME B16.5 and API 570 define strict limits for the maximum depth and radial projection of imperfections. For example, for Class 150 flanges, the maximum radial projection of an imperfection (the distance it extends across the gasket surface) is limited by size:
For NPS 1/2 to 2: Max imperfection is 0.03 inches (0.8 mm) .
For NPS 2-1/2 to 6: Max imperfection is 0.06 inches (1.6 mm) .
For NPS 8 to 12: Max imperfection is 0.09 inches (2.3 mm) .
If a flange face has a scratch deeper than these limits, it must be remachined in the shop or field (using a flange facer) to restore the required serrated finish, or the flange must be replaced.
Gaskets and Bolting Materials
The inspector must verify that the gaskets and fasteners installed in the joint match the piping specification. Gaskets are designed to deform under bolt load to fill the microscopic imperfections on the flange faces. Common gasket types include:
Spiral Wound Gaskets : Composed of alternating metal windings and non-metallic fillers. They typically feature an outer retaining ring to center the gasket and prevent blowout.
Metallic Ring Gaskets : Used exclusively in Ring-Type Joint (RTJ) flanges.
Fasteners must be checked for proper material specification:
Heavy-Duty Bolting : Standard carbon steel bolts will relax (stretch) at high temperatures, causing the joint to leak. Therefore, high-temperature service requires alloy steel studs (typically ASTM A193 Grade B7 ) and heavy hex nuts ( ASTM A194 Grade 2H ).
Low-Temperature Bolting : Requires impact-tested alloys, such as ASTM A320 Grade L7 .
ASME B16.5 Markings and Flange Identification
B16.5 requires flanges to be marked with identifying information that inspectors use to confirm material , pressure class , and size match the piping specification. Typical markings include manufacturer, material designation (or ASTM grade), class (e.g., 150, 300), and size. On the API 570 exam, mismatched class or material markings relative to the design temperature/pressure are a classic “weakest link” finding — a correctly thick pipe wall does not rescue an under-rated flange.
Flange Testing Awareness
B16.5 also addresses pressure testing of flanges as manufactured. In-service inspectors are not re-proving factory hydrotests, but they must understand that flange class pressure-temperature ratings already incorporate the standard’s design basis — field hydrotests of piping systems must not exceed flange limits without engineering control.