Study guide

13.3 Corrosion Fatigue

API 571 Corrosion and Materials Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Structure, Terminology & Corrosion Fundamentals

1.1 API 571 Certification, Exam Structure & RP 571 Framework 1.2 Corrosion Science Fundamentals: Electrochemical Cells, Polarization & Passivity 1.3 Key Process Variables, Morphology Patterns & NDE Terminology

2 Chapter 2: Atmospheric, Water & Soil Corrosion

2.1 Atmospheric Corrosion & Soil Corrosion 2.2 Corrosion Under Insulation (CUI) 2.3 Cooling Water, Boiler Water & Oxygenated Process Water Corrosion

3 Chapter 3: Microbial, Electrochemical & Velocity-Induced Metal Loss

3.1 Microbiologically Influenced Corrosion (MIC) & Brine Corrosion 3.2 Galvanic Corrosion, Concentration Cell Corrosion & Dealloying 3.3 Erosion/Erosion-Corrosion & Cavitation

4 Chapter 4: Refining Sour Water & Overhead Systems Corrosion

4.1 Acidic Sour Water & Alkaline Sour Water (Ammonium Bisulfide) Corrosion 4.2 Ammonium Chloride and Amine Hydrochloride Corrosion 4.3 Flue Gas Dew Point Corrosion & Aqueous Organic Acid Corrosion

5 Chapter 5: Acid Gas, Amine & Mineral Acid Systems

5.1 Amine Corrosion & Carbon Dioxide (CO2) Sweet Corrosion 5.2 Hydrochloric Acid (HCl) Corrosion & Phenol Corrosion 5.3 Caustic Corrosion (Caustic Gouging)

6 Chapter 6: Heavy Oil, Alkylation & Specialty Acid Services

6.1 Naphthenic Acid Corrosion (NAC) 6.2 Sulfuric Acid Corrosion & Phosphoric Acid Corrosion 6.3 Hydrofluoric (HF) Acid Corrosion

7 Chapter 7: High-Temperature Oxidation & Sulfidation

7.1 High-Temperature Oxidation 7.2 Sulfidation in H2-Free Environments 7.3 High-Temperature H2/H2S Corrosion (Couper-Gorman)

8 Chapter 8: High-Temperature Carbon, Nitrogen & Ash Reactions

8.1 Carburization, Decarburization & Metal Dusting 8.2 Nitriding, Fuel Ash Corrosion & Refractory Degradation 8.3 Gaseous Oxygen-Enhanced Ignition and Combustion

9 Chapter 9: High-Temperature Hydrogen Attack & High-Temp Rupture

9.1 High-Temperature Hydrogen Attack (HTHA) Mechanisms & Nelson Curves 9.2 HTHA Inspection, Detection Methods & Mitigation 9.3 Creep, Stress Rupture & Short-Term Overheating

10 Chapter 10: Wet H2S Cracking Mechanisms

10.1 Hydrogen Blistering & Hydrogen-Induced Cracking (HIC) 10.2 Stress-Oriented Hydrogen-Induced Cracking (SOHIC) 10.3 Sulfide Stress Cracking (SSC)

11 Chapter 11: Stainless Steel & Nickel Alloy Stress Corrosion Cracking

11.1 Chloride Stress Corrosion Cracking (Cl- SCC) 11.2 Polythionic Acid Stress Corrosion Cracking (PASCC) 11.3 Caustic Stress Corrosion Cracking (Caustic Embrittlement)

12 Chapter 12: Environmental Cracking in Chemical & Refining Services

12.1 Amine Stress Corrosion Cracking 12.2 Carbonate Stress Corrosion Cracking & Ammonia SCC 12.3 HF Cracking (HSC & HF SCC of Ni Alloys) & Ethanol SCC

13 Chapter 13: Mechanical, Thermal & Corrosion Fatigue

13.1 Mechanical and Vibration-Induced Fatigue 13.2 Thermal Fatigue & Thermal Shock 13.3 Corrosion Fatigue

14 Chapter 14: Metallurgical Phase Embrittlement & Cast Iron Degradation

14.1 885 °F (475 °C) Embrittlement 14.2 Sigma Phase Embrittlement 14.3 Graphitic Corrosion of Cast Irons

15 Chapter 15: Thermal Degradation of Microstructure & Grain Structure

15.1 Graphitization 15.2 Spheroidization (Softening) 15.3 Temper Embrittlement & Strain Aging

16 Chapter 16: Toughness Loss, Welding & Dissimilar Metal Cracking

16.1 Brittle Fracture 16.2 Dissimilar Metal Weld (DMW) Cracking 16.3 Stress Relaxation Cracking (Reheat Cracking)

17 Chapter 17: Environmental Embrittlement & Specialized Hydriding

17.1 Hydrogen Embrittlement (HE) 17.2 Liquid Metal Embrittlement (LME) 17.3 Titanium Hydriding

13.3 Corrosion Fatigue

Key Takeaways Explain This Topic AI

Corrosion Fatigue (API RP 571 Section 3.21) represents the synergistic mechanical-electrochemical degradation resulting from the combined interaction of cyclic mechanical or thermal stresses and an aggressive corrosive environment.

The defining hallmark of corrosion fatigue is the complete elimination of the fatigue endurance limit: in a corrosive environment, carbon and low-alloy steels exhibit no threshold stress below which they can endure infinite cycles, failing at significantly lower stress amplitudes and fewer cycles than in air.

Crack initiation begins with cyclic strain rupturing the protective passive film or oxide scale, allowing localized anodic dissolution to create micro-pits; sharp pit roots serve as intense stress concentrations from which transgranular, blunt-tipped cracks propagate.

Low cycling frequencies drastically increase corrosion fatigue crack growth rates because slower cycle periods allow more time for electrochemical dissolution and corrosion reactions to proceed at the exposed crack tip during each load cycle.

Deaerator storage vessels and boiler waterwall tubes are premier industrial assets vulnerable to corrosion fatigue; mitigation relies on strict control of dissolved oxygen and boiler water pH, alongside reducing cyclic stresses through vibration dampening and piping redesign.

Last updated: September 2026

13.3 Corrosion Fatigue — API RP 571 Section 3.21

Corrosion Fatigue is a complex, synergistic damage mechanism cataloged under API RP 571 Section 3.21 . It is defined as the accelerated cracking of structural metals resulting from the simultaneous interaction of cyclic (fatigue) stresses and a corrosive electrochemical environment . The distinguishing operational hallmark of corrosion fatigue is that the combined rate of damage is vastly greater than the simple mathematical sum of mechanical fatigue and baseline general corrosion acting independently.

In petroleum refining, power generation, and petrochemical processing, corrosion fatigue represents a premier integrity hazard for steam-generating systems, boiler feedwater deaerators, heat exchangers, rotating machinery shafts, and subsea structures. Left undetected, it causes sudden, brittle-like through-wall fractures at nominal operating stresses well below standard design allowances.

The Synergistic Degradation Mechanism

To understand corrosion fatigue, materials engineers analyze the continuous mechanical-chemical interplay occurring at the wetted metal surface: THE CORROSION FATIGUE SYNERGISTIC CYCLE

  • 1. Passive Scale / Film Rupture 2. Localized Anodic Dissolution
  • ┌─────────────────────────────────┐ ┌─────────────────────────────────┐
  • │ Cyclic tensile strain stretches │ │ Bare metal substrate exposed. │
  • │ metal, rupturing the protective │────>│ Anodic dissolution attacks the │
  • │ magnetite (Fe3O4) or oxide film.│ │ micro-gap, forming a sharp pit. │
  • └─────────────────────────────────┘ └─────────────────────────────────┘
  • ▲ │
  • │ │
  • │ ▼
  • 4. Oxide Wedging & Re-passivation 3. Subcritical Crack Propagation
  • ┌─────────────────────────────────┐ ┌─────────────────────────────────┐
  • │ Corrosion products fill crack │ │ Pit root concentrates cyclic │
  • │ fissure, wedging crack open │<────│ stress (Kt >= 3.0); crack │
  • │ during compressive cycle. │ │ propagates transgranularly. │
  • └─────────────────────────────────┘ └─────────────────────────────────┘
  • 1. Step-by-Step Degradation Sequence

Passivating Film Rupture: In aqueous service (such as boiler feedwater), carbon steel forms a thin protective passivation scale of magnetite ( F e 3 O 4 Fe_3O_4 F e 3 ​ O 4 ​ ). Under cyclic tensile strains, microscopic slip steps emerge at the surface, rupturing the brittle oxide layer and exposing fresh, bare metal substrate to the electrolyte.

Localized Anodic Dissolution (Micro-Pitting): The newly exposed bare metal has a highly active electrochemical potential, functioning as a tiny anode surrounded by a large cathodic area of intact passive magnetite scale. Rapid galvanic micro-dissolution occurs: F e → F e 2 + + 2 e − (Anodic Dissolution) Fe \rightarrow Fe^{2+} + 2e^-\quad \text{(Anodic Dissolution)} F e → F e 2 + + 2 e − (Anodic Dissolution) This localized attack forms microscopic, sharp-bottomed corrosion pits.

Fatigue Crack Initiation: The sharp root of the corrosion pit introduces an intense geometric stress concentration factor ( K t ≥ 3.0 K_t \ge 3.0 K t ​ ≥ 3.0 ). Cyclic mechanical or thermal stresses concentrate at the pit tip, initiating a transgranular Stage I fatigue crack.

Cyclic Crack Propagation & Dynamic Electrolyte Pumping: As cyclic tensile loads pull the crack mouth open, fresh corrosive electrolyte is drawn into the crack tip via capillary pumping. Anodic dissolution dissolves the strained metal at the crack tip, while the cyclic stress drives mechanical crack extension. Concurrently, cathodic hydrogen reduction can liberate atomic hydrogen at the crack tip, contributing to localized hydrogen embrittlement.

Oxide Wedging: Dense iron oxide corrosion products precipitate inside the crack fissure. Because iron oxides occupy significantly greater molar volume than the host steel (Pilling-Bedworth ratio > 2.0), the corrosion products act as a physical wedge. This prevents complete closure of the crack during compressive load cycles, increasing the effective stress intensity ratio ( R = K min ⁡ / K max ⁡ R = K_{\min} / K_{\max} R = K m i n ​ / K m a x ​ ) and drastically accelerating crack propagation rates.

Elimination of the Fatigue Endurance Limit

The most critical technical concept governing corrosion fatigue is the complete elimination of the fatigue endurance limit in a corrosive environment. S-N CURVE COMPARISON: AIR VS. CORROSIVE SERVICE

  • Cyclic Stress
  • Amplitude (S)
  • │
  • │ FATIGUE IN AIR (BENIGN)
  • │──────┐
  • │ └───┐
  • │ └───┐
  • S_e ───┼──────────────┴───────────────────────────► Horizontal Endurance Limit
  • │ (Infinite life below S_e)
  • │ CORROSION FATIGUE (CORROSIVE)
  • │──────┐
  • │ └───┐
  • │ └───┐
  • │ └───┐
  • │ └───┐
  • │ └───┐
  • │ └───┐

│ └───► NO ENDURANCE LIMIT!

  • │ (Continuous downward slope)
  • └─────────────────────────────────────────►
  • 10^3 10^4 10^5 10^6 10^7 10^8 Cycles (N)

In Dry Air Service: Carbon and low-alloy steels exhibit a well-defined horizontal endurance limit ( S e ≈ 0.40 − 0.50 × S u t S_e \approx 0.40 - 0.50 \times S_{ut} S e ​ ≈ 0.40 − 0.50 × S u t ​ ). If cyclic stress remains below S e S_e S e ​ , the component will endure infinite cycles ( N > 10 7 N > 10^7 N > 1 0 7 ) without failing.

In Corrosive Service: The presence of even a mildly corrosive electrolyte completely eliminates the endurance limit. The S-N curve continues to decline monotonically with no horizontal plateau. Consequently, there is no safe cyclic stress threshold in corrosive service ; given sufficient operating time and stress cycles, carbon steel will inevitably crack and fail at stress levels far below its normal air fatigue limit.

Critical Influencing Factors

Corrosion fatigue crack propagation kinetics depend heavily on the interplay between dynamic mechanical cycles and chemical reaction kinetics:

1. Cycling Frequency (The Inverse Frequency Effect)

In mechanical fatigue in air, test frequency between 1 Hz and 100 Hz has minimal effect on fatigue life. In corrosion fatigue, however, cycling frequency is a primary controlling variable :

Lower cycling frequencies (e.g., 0.001 Hz to 1.0 Hz) result in drastically faster crack propagation per cycle ( d a / d N da/dN d a / d N ).

At low frequencies (characteristic of plant thermal cycling, batch filling, or boiler pressure swings), the crack tip remains open under peak tensile stress for a prolonged duration during each cycle. This provides ample physical time for electrochemical anodic dissolution and hydrogen diffusion to proceed before the cycle reverses.

At high frequencies (e.g., 50 Hz to 100 Hz), the mechanical cycle reverses too rapidly for significant electrochemical dissolution to accumulate during any single cycle.

2. Environmental Corrosiveness and Water Chemistry

Dissolved Oxygen ( O 2 O_2 O 2 ​ ): Dissolved oxygen is the primary cathode depolarizer driving corrosion fatigue in boiler and deaerator systems: O 2 + 2 H 2 O + 4 e − → 4 O H − (Cathodic Reduction) O_2 + 2H_2O + 4e^- \rightarrow 4OH^-\quad \text{(Cathodic Reduction)} O 2 ​ + 2 H 2 ​ O + 4 e − → 4 O H − (Cathodic Reduction) Dissolved oxygen concentrations as low as 10 to 50 parts per billion (ppb) can initiate severe corrosion fatigue. Completely deaerated water ( < 5 ppb O 2 < 5\text{ ppb } O_2 < 5 ppb O 2 ​ ) markedly suppresses crack initiation.

pH Level: Acidic environments ( pH < 7.0 \text{pH} < 7.0 pH < 7.0 ) accelerate cathodic hydrogen evolution and prevent the formation of protective magnetite ( F e 3 O 4 Fe_3O_4 F e 3 ​ O 4 ​ ), accelerating cracking. Alkaline pH levels between 9.0 and 10.5 promote stable passivation.

Aggressive Anions: Chlorides ( C l − Cl^- C l − ) and sulfates ( S O 4 2 − SO_4^{2-} S O 4 2 − ​ ) disrupt passive films, accelerating pitting and increasing crack growth rates by orders of magnitude.

3. Stress Amplitude and Residual Stress

Corrosion fatigue does not require cyclic stresses to exceed yield. Residual tensile stresses from un-stress-relieved welding dramatically shift the mean stress ratio upward ( R > 0.5 R > 0.5 R > 0.5 ), holding crack tips in a permanently open state and accelerating electrolyte ingress.

High-Risk Industrial Equipment & Case Studies PRIMARY REFINERY & UTILITY SERVICES

  • Boiler Feedwater Deaerators Boiler Waterwall & Economizers
  • ┌─────────────────────────────────────┐ ┌─────────────────────────────────────┐
  • │ - Storage vessels & heater sections │ │ - Tubes subject to thermal bowing │
  • │ - Welds in heat-affected zone (HAZ) │ │ - Gas flow pulsation & soot blowing │
  • │ - High residual welding stress │ │ - Cracks initiate on wetted ID │
  • │ - Periodic oxygen excursions │ │ - Pitted internal waterwall tubes │
  • └─────────────────────────────────────┘ └─────────────────────────────────────┘
  • Rotating Machinery & Pumps Offshore Risers & Subsea Flowlines
  • ┌─────────────────────────────────────┐ ┌─────────────────────────────────────┐
  • │ - Boiler feed pump shafts & impellers│ │ - Wave-induced cyclic bending │
  • │ - Rotating bending in brine/water │ │ - Marine seawater / wet CO2 service │
  • │ - Keyways and seal transitions │ │ - Complete absence of fatigue limit │
  • │ - Catastrophic shaft severance │ │ - Welded riser joint vulnerability │
  • └─────────────────────────────────────┘ └─────────────────────────────────────┘
  • 1. Boiler Feedwater Deaerator Storage Vessels

Historically, catastrophic explosions of boiler feedwater deaerator storage vessels prompted industry-wide investigations (culminating in NACE SP0590 / RP0590 ). Deaerator vessels experience a lethal combination of drivers:

High residual tensile stresses in non-PWHT circumferential and longitudinal welds.

Cyclic thermal and pressure fluctuations from unstable steam injection, cold water makeup, and water-hammer vibration.

Corrosive environment containing elevated dissolved oxygen prior to complete deaeration.

Cracks initiate silently along internal weld toes and heat-affected zones (HAZs), propagating through-wall and causing catastrophic vessel rupture.

2. Boiler Waterwall and Economizer Tubing

Boiler waterwall tubes in industrial steam boilers experience cyclic mechanical bending moments caused by thermal expansion mismatch between furnace walls and structural buckstays, burner vibrations, and soot-blower operation. In the presence of boiler water containing dissolved oxygen or acidic pH excursions, parallel arrays of transgranular corrosion fatigue cracks initiate on the internal wetted ID surface of the tubes, predominantly oriented circumferentially.

3. Rotating Equipment Shafts

Centrifugal pump shafts, mixer shafts, and compressor rotors operating in corrosive process fluids, sour water, or cooling brine undergo high-cycle rotating bending stresses. Micro-pits form at shaft seal areas, keyways, and shoulder radii, initiating corrosion fatigue cracks that shear the shaft.

Morphology and Failure Analysis

Distinguishing corrosion fatigue from pure mechanical fatigue and stress corrosion cracking (SCC) is a vital metallurgical skill tested on the API 571 examination:

Diagnostic Feature Corrosion Fatigue (API RP 571 Sec 3.21) Mechanical Fatigue (API RP 571 Sec 3.43) Stress Corrosion Cracking (e.g. Caustic/Cl- SCC)

Stress Type Cyclic mechanical or thermal stress Cyclic mechanical stress Static or residual tensile stress (monotonic)

Environment Corrosive electrolyte required Dry, benign, or non-corrosive air Specific chemical species (caustic, chlorides, amines)

Crack Initiation Roots of surface corrosion pits Surface notches, fillet toes, slip bands Passive film breakdown, pitting, or intergranular attack

Crack Profile Broad, blunt-tipped, wedge-shaped Extremely sharp, fine, tightly closed Sharp, highly branched, dendritic fissures

Crack Path Transgranular (predominantly) Transgranular Intergranular (Caustic, Amine) or Transgranular (Cl- SCC)

Fissure Contents Heavily packed with dense iron oxide scale Clean or minimally oxidized Often lined with chemical scale / corrosion product

Crack Array Multiple parallel cracks along pitted surface Typically a single dominant crack Dense spider-web or branched crack network CORROSION FATIGUE CRACK MORPHOLOGY

  • Internal Wetted Surface (Corrosive Boiler Water / Deaerator Service)
  • ═══════════╤══════════════════════╤═════════════════════╤════════════
  • │ Pits │ │
  • / \ / \ / \
  • │ │ Micro-pits │ │ │ │
  • / \ act as crack / \ / \
  • │ █ │ starters │ █ │ │ █ │
  • │ █ │ │ █ │ │ █ │
  • \ █ / \ █ / \ █ /
  • \ █ / \ █ / \ █ /
  • ▼ ▼ ▼ ▼ ▼ ▼
  • MULTIPLE PARALLEL CRACKS: Transgranular, wide, wedge-shaped,

and tightly packed with dense black iron oxide (magnetite) scale.

Prevention and Engineering Mitigations

Mitigating corrosion fatigue requires attacking both the chemical environment and the cyclic stress state:

1. Water Treatment & Chemical Control

Dissolved Oxygen Scavenging: Maintain boiler feedwater dissolved oxygen below 5 to 7 ppb through effective mechanical deaerator operation and continuous injection of chemical oxygen scavengers (such as sodium sulfite in low-pressure boilers or hydrazine, carbohydrazide, and DEHA in high-pressure boilers).

pH Passivation: Maintain boiler water pH within the optimal alkaline passivating range ( 9.0 to 10.5 ) using coordinated phosphate treatment or volatile amine dosing (e.g., morpholine, cyclohexylamine) to stabilize protective magnetite films.

Elimination of Contaminants: Eliminate chloride and sulfate ingress by maintaining high-purity condensate polishers and demineralizer beds.

2. Residual Stress Relief & Structural Redesign

PWHT for Deaerators: NACE SP0590 recommends PWHT of deaerator vessel welds (new construction and repairs) to reduce the residual welding stresses that drive cracking.

Weld Toe Flush Grinding: Internally grind weld crowns and fillet toes smooth and flush ( r ≥ 1 / 4 in r \ge 1/4\text{ in} r ≥ 1/4 in ) to reduce geometric stress concentration factors from K t > 3.0 K_t > 3.0 K t ​ > 3.0 down toward K t ≈ 1.0 K_t \approx 1.0 K t ​ ≈ 1.0 .

Vibration Dampening & Support Redesign: Install rigid piping guides, acoustic pulsation dampers, and flexible expansion joints to minimize mechanical vibration and water-hammer cycles.

3. Materials Selection & Coatings

Upgrade critical pump shafts and agitated components from carbon steel to corrosion-resistant alloys (such as Alloy 625, Alloy 718, or duplex stainless steels).

Apply corrosion-resistant alloy (CRA) weld overlays (such as 300-series stainless steel or nickel-base alloys) to deaerator internal weld seams.

Inspection, Non-Destructive Examination (NDE) & Deaerator Protocols

Inspection Technique Application & Protocol Industry Role & Sensitivity

Wet Fluorescent Magnetic Particle Testing (WFMT) Primary recommended method for deaerator internal welds per NACE SP0590 ; carbon steel vessels. Gold standard. Performed using an electromagnetic AC yoke following abrasive white-metal grit blasting (SSPC-SP 5). Extremely sensitive for detecting tight, oxide-filled, pit-initiated cracks.

Alternating Current Field Measurement (ACFM) Surface crack detection through internal vessel linings or thin coatings without grit blasting. Detects and provides accurate length and depth sizing of surface-breaking cracks; excellent for screening welds.

Angle Beam Shear Wave UT / PAUT External volumetric scanning of deaerators, boiler tubes, and pump shafts while in service. Phased Array UT detects ID-initiated surface-breaking cracks from the external OD surface when internal vessel entry is impossible.

Liquid Penetrant Testing (PT) Non-ferromagnetic components (austenitic stainless pump shafts, impellers, copper-nickel tubes). Detects surface cracks. Requires aggressive chemical cleaning to dissolve dense oxide scales packed within crack openings.

Loading diagram... Corrosion Fatigue Mechanism, Endurance Limit Elimination, and NACE SP0590 Mitigations