Study guide

3.3 Leak Detection Systems, Secondary Containment & Under-Tank Monitoring

API 653 Aboveground Storage Tank Inspector Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: API 653 Scope, Inspector Certification & Roles

1.1 Scope of API 653, Tank Types & Construction Standards 1.2 Inspector Roles, Responsibilities & Certification Requirements 1.3 Inspection Planning, Safety, Confined Space Entry & Preparation

2 Chapter 2: Tank Shell & Roof Components Inspection

2.1 Fixed Roof Types, Structural Supports & Inspection Practices 2.2 Floating Roofs, Seals, Drainage & Operational Issues 2.3 Shell Courses, Welds, Attachments & Wind Girders 2.4 Tank Appurtenances, Nozzles, Manways & Piping Connections

3 Chapter 3: Tank Bottom & Foundation Inspection

3.1 Tank Bottom Types, Annular Plates & Internal Bottom Inspection 3.2 Foundation Types (Concrete Ringwall, Earth, Asphalt) & Inspection 3.3 Leak Detection Systems, Secondary Containment & Under-Tank Monitoring

4 Chapter 4: Corrosion & Damage Mechanisms in Storage Tanks

4.1 Atmospheric Corrosion, Condensation & External Deterioration 4.2 Corrosion Under Insulation (CUI) & Piping/Nozzle Interfaces 4.3 Soil-Side Corrosion, Under-Bottom Pitting & Microbiologically Induced Corrosion (MIC) 4.4 Product-Side Deterioration: Chemical Attack, Ethanol SCC, Concentration Cell & Sulfuric Acid Corrosion

5 Chapter 5: Materials, Toughness & Brittle Fracture Prevention

5.1 Tank Steels, Material Specifications & Historic Standards 5.2 Brittle Fracture Assessment: Figure 5.1 Decision Tree & Exemption Curves (API 653 Section 5) 5.3 Charpy V-Notch Impact Testing & Minimum Design Metal Temperature (MDMT)

6 Chapter 6: Cathodic Protection & Interior Linings

6.1 Cathodic Protection Principles & Systems for Tank Bottoms (API RP 651) 6.2 CP Criteria, Surveys, Potential Measurements & Interference (API RP 651) 6.3 Tank Bottom Interior Linings, Surface Prep & Inspection (API RP 652)

7 Chapter 7: Corrosion Rates, Remaining Life & Inspection Intervals

7.1 Determining Corrosion Rates (Short-Term vs. Long-Term) 7.2 Remaining Life Calculations & Limiting Components 7.3 Establishing In-Service & Out-of-Service Inspection Intervals (API 653 Section 6)

8 Chapter 8: Tank Shell Minimum Thickness Evaluation

8.1 Shell Minimum Thickness Calculations (tmin for Hydrostatic & Operating Levels) 8.2 One-Foot Method, Variable Design Point & Reconstructed-Tank Shell Thickness 8.3 Joint Efficiency (E) Selection, Missing Data & Radiography Factors 8.4 Evaluation of Pitting, Localized Thin Areas (LTA) & Critical Length (L)

9 Chapter 9: Bottom Plate & Annular Ring Thickness Evaluation

9.1 Minimum Bottom Thickness Formulations (MRT, MRTbottom, MRTlinear) 9.2 Annular Plate Evaluation, Stress Criteria & Critical Zones 9.3 Bottom Pitting Evaluation & Remaining Thickness Before Next Inspection

10 Chapter 10: Tank Repairs & Alterations Standards

10.1 Classification: Repair vs. Alteration vs. Reconstruction (API 653 Section 9) 10.2 Shell Plate Replacement, Lapped Patch Plates & Insert Plates 10.3 Shell Penetrations, Door Sheets & Nozzle Additions 10.4 Hot Tapping Requirements, Limitations & Pre-Engineering (API 653 Section 9.15 & API Publ 2201)

11 Chapter 11: Welding Procedures, Qualifications & Quality Control

11.1 Welding Procedure Specification (WPS) & Procedure Qualification Record (PQR) per ASME IX 11.2 Welder Performance Qualification (WPQ) & Continuity per ASME IX 11.3 Essential, Non-Essential & Supplementary Essential Variables 11.4 Preheating, Post-Weld Heat Treatment (PWHT) & Weld Flaw Remediation

12 Chapter 12: Nondestructive Examination (NDE) Methods

12.1 Visual Examination (VT) & Magnetic Particle Testing (MT) per ASME V 12.2 Liquid Penetrant (PT) & Ultrasonic Thickness Measurement (ASME V Article 6 & SE-797) 12.3 Radiographic Testing (RT): Acceptance Criteria, Film Interpretation & ASME V/API 650

13 Chapter 13: Hydrostatic Testing & Post-Repair Examination

13.1 Hydrostatic Test Triggers, Exemption Criteria & Major Alterations (API 653 Section 12.3) 13.2 Leak Testing: Vacuum Box, Tracer Gas, Diesel & Air Pressure Tests 13.3 NDE Examination Requirements for Shell, Bottom, Roof & Nozzle Welds (API 653 Section 12.1)

14 Chapter 14: Relief Devices, Tank Settlement & Nameplate Records

14.1 Pressure & Vacuum Relief Devices, Venting Principles (API RP 576 & API 2000) 14.2 Tank Settlement Types: Uniform, Tilt, Out-of-Plane & Edge Settlement (API 653 Annex B) 14.3 Evaluating Settlement Limits, Cosine Curve Analysis & Remedial Action 14.4 Tank Marking, Nameplates, Inspection Reports & Recordkeeping (API 653 Section 13)

3.3 Leak Detection Systems, Secondary Containment & Under-Tank Monitoring

Key Takeaways Explain This Topic AI

Release Prevention Barriers (RPB) per API 650 Annex I provide an impermeable secondary boundary that intercepts floor leaks and channels product to observation ports before environmental release.

Double-bottom retrofits utilize synthetic geomembranes (40-100 mil HDPE) or secondary steel floors with slotted pipe networks and interstitial spacer grids for continuous leak detection.

Secondary containment diked basins must hold at least 110% of the largest tank's volume (or 100% plus 24-hr/25-yr storm precipitation), with drainage valves locked closed during normal operation.

Under-tank leak monitoring combines slotted telltale weep pipes, electrical resistance sensor cables, and hydrocarbon vapor detection sniff tubes.

Advanced subsurface monitoring integrates perimeter groundwater monitoring wells, mass-balance automated tank gauging, and in-service Acoustic Emission Testing (AET).

Last updated: September 2026

3.3 Leak Detection Systems, Secondary Containment & Under-Tank Monitoring

Environmental Containment Standard: Aboveground storage tank integrity relies on a defense-in-depth architecture. If the primary steel bottom is breached by localized pitting, engineered Release Prevention Barriers (RPB) , under-tank leak detection networks, and external secondary containment dikes prevent stored hydrocarbons from contaminating groundwater and surrounding ecosystems.

  • 1. Release Prevention Barriers (RPB) per API 650 Annex I
  • Definition and Purpose

Per API 650 Annex I ( Undertank Leak Detection and Subgrade Protection ) — the annex API 653 points to for release prevention barrier details — an RPB is defined as a second barrier installed beneath or integrated into the tank bottom that:

Prevents the escape of released liquid product into the subsoil and groundwater.

Deflects and channels any leaking liquid or vapor to an accessible perimeter collection and detection point.

Enables rapid operator detection of primary bottom leaks before significant inventory loss occurs. +-----------------------------------------------------------------------------------------+

  • | API 650 ANNEX I: DOUBLE-BOTTOM WITH RELEASE PREVENTION BARRIER (RPB) |
  • | |
  • | Tank Shell Plate |
  • | | | |
  • | | |====== PRIMARY TANK BOTTOM (New Steel Floor) ========================= |
  • | | | |
  • | | |...... Interstitial Space (Sand Cushion / Drainage Grid) .............. |
  • | | | |
  • | ======|==|====== SECONDARY BARRIER / RPB (Old Bottom or 80-100 mil HDPE Liner) == |
  • | | | |
  • | [Weep Pipe]======> Slotted Telltale Pipe Channels Leak to Perimeter Observation |
  • | | Trough Outside the Ringwall |
  • | +-----------------------------------------------------------------------+ |
  • | Concrete Ringwall Foundation |
  • +-----------------------------------------------------------------------------------------+
  • RPB Configurations under Annex I

API 650 Annex I outlines several approved engineering configurations for RPBs:

Flexible Membrane Liners (Geomembranes): Continuous synthetic polymeric sheets installed beneath the tank bottom or between floors. Materials include High-Density Polyethylene (HDPE) , polyvinyl chloride (PVC), and reinforced chlorosulfonated polyethylene (CSPE). Geomembranes are commonly specified at 40 to 100 mils (1.0 to 2.5 mm) — heavier 80–100 mil sheet is used where puncture risk is high — and must demonstrate chemical compatibility with the stored product, puncture resistance against crushed stone, and thermal stability.

Double-Steel Bottoms: Installing a new, elevated steel floor above an existing compromised floor. The old bottom serves as the secondary barrier, with an interstitial space (3 to 6 in. thick) filled with clean, washed sand, lightweight cellular concrete, or an open drainage mesh.

Impervious Concrete Slabs: Monolithic concrete foundations coated with hydrocarbon-resistant elastomeric coatings and cast with radial drainage channels.

2. Under-Tank Leak Detection Systems

To satisfy regulatory standards (such as EPA 40 CFR Part 280/112) and API 650 Annex I, the interstitial space beneath an RPB or double bottom must be equipped with active or passive leak detection networks:

A. Slotted Telltale (Weep) Pipes

Design: Radial perforated or slotted plastic (PVC/HDPE) or stainless steel pipes embedded within the interstitial sand cushion or drainage layer.

Layout: Pipes are arranged in a spoke-wheel or grid pattern, sloping downward toward the perimeter and penetrating horizontally through the concrete ringwall at intervals of 20 to 30 ft (6 to 9 m) around the circumference.

Inspection Protocol: In-service external rounds require inspectors to visually examine all telltale pipe outlets terminating in the ringwall. Pipes should be fitted with downward-facing elbows, insect screens, and clean, accessible inspection troughs. Any liquid discharge must be immediately sampled and tested to distinguish condensation water from hydrocarbon leakage.

B. Electrical Resistance and Sensor Cable Grids

Conductive Cables: Polymer sensor cables installed in the interstitial sand space that experience a permanent, dramatic change in electrical impedance when contacted by liquid hydrocarbons.

Point Sensors: Optical refraction or float-switch probes positioned inside collection sumps around the perimeter.

Real-Time Telemetry: These systems connect directly to the facility Distributed Control System (DCS) or Supervisory Control and Data Acquisition (SCADA) network, providing continuous automated leak alarm monitoring with location resolution to within several feet.

C. Hydrocarbon Vapor Detection Probes (Sniff Tubes)

Operating Principle: Slotted sampling tubes installed beneath the bottom plates through which soil gases are extracted and tested.

Application: Highly volatile products (gasoline, jet fuel, light solvents) generate significant vapor pressure. Even micro-seepage insufficient to produce a liquid stream will liberate volatile organic compounds (VOCs).

Field Testing: Portable Photoionization Detectors (PID) or Flame Ionization Detectors (FID) draw air samples from each sniff tube to detect parts-per-million (ppm) hydrocarbon vapor spikes long before product breaks through the foundation.

  • 3. Secondary Containment Diking (Bunds) and Regulatory Mandates
  • Environmental Regulations (EPA SPCC & NFPA 30)

External secondary containment is mandated by the US EPA Spill Prevention, Control, and Countermeasure (SPCC) rule (40 CFR Part 112) and NFPA 30 (Flammable and Combustible Liquids Code) to retain catastrophic product releases resulting from shell rupture, overfilling, or piping failure.

Containment Capacity Sizing Criteria

Secondary containment basins (dikes or bunds) must satisfy strict minimum volumetric capacity calculations:

Required Dike Volume >= 100% of Largest Tank Capacity + Precipitation Freeboard

Standard Industry Metric: In practice, this standard translates to a minimum requirement of 110% of the volume of the largest enclosed tank .

Precipitation Allowance: The freeboard must comfortably contain the anticipated storm runoff from a 24-hour, 25-year rainfall event over the entire basin footprint without overtopping the dike walls.

Dike Wall Construction and Inspection

Dike Construction Structural Attributes Common Failure Modes & Inspection Focus

Compacted Earthen Berms Cost-effective; wide sloped berms (3:1 or 2:1 run-to-rise); low permeability clay (k <= 1 x 10^-7 cm/s). Desiccation cracking during dry weather; animal burrowing voids; erosion washouts from heavy rain; deep weed root penetrations.

Reinforced Concrete Walls Minimal spatial footprint; vertical walls ideal for space-constrained terminals and marine facilities. Expansion/construction joint seal failure; seismic shear cracking; concrete spalling; corrosion of waterstop gaskets.

Synthetic Geomembrane Dikes HDPE or XR-5 geomembrane liners covering earthen berms, anchored in perimeter trenches. Seam weld delamination; puncture tears from maintenance equipment; UV embrittlement; ballast slippage.

Dike Drainage and Operation Rules

Drainage Valves: Gravity storm drains penetrating dike walls must be fitted with external manual isolation valves.

Lock-Out Protocol: Dike drain valves must remain locked in the closed position at all times during normal facility operations.

Controlled Discharge: Accumulated storm water may only be discharged after an operator conducts a visual inspection verifying the absence of surface oil sheen or hydrocarbon odor. Every discharge event must be logged with date, volume, operator signature, and discharge water quality verification.

Piping Penetrations: Where product piping penetrates concrete or earthen dikes, liquid-tight, flexible fire-resistant seals must be maintained to prevent catastrophic wall washouts during a tank spill.

4. Advanced and Subsurface Monitoring Technologies

Beyond immediate under-tank barriers, facilities employ global surveillance technologies to maintain environmental integrity:

Groundwater Monitoring Wells

Hydrogeologic Placement: A network of sentinel monitoring wells installed around the perimeter of the tank farm, strategically positioned both upgradient (to establish baseline background water quality) and downgradient (along the direction of groundwater flow).

Sampling Protocol: Quarterly or semi-annual sampling utilizing bailers or automated interface probes detects dissolved-phase petroleum hydrocarbons (benzene, toluene, ethylbenzene, xylenes - BTEX) or free-phase Light Non-Aqueous Phase Liquid (LNAPL) floating on the groundwater table.

Inventory Reconciliation (Mass Balance & ATG)

Automated Tank Gauging (ATG): High-precision magnetostrictive or radar level gauges continuously track liquid level, product temperature, density profiles, and water bottom interface levels.

Statistical Inventory Reconciliation (SIR): Sophisticated mass-balance software correlates tank level movements with pipeline meter throughput. By applying volumetric temperature correction factors (API Manual of Petroleum Measurement Standards), SIR algorithms detect chronic, low-rate leaks that would otherwise be masked by ambient temperature expansion and contraction.

Acoustic Emission Testing (AET)

Acoustic Emission Testing (AET) is an advanced, non-intrusive non-destructive testing methodology capable of evaluating tank bottom floor condition while the tank remains fully in service : +-----------------------------------------------------------------------------------------+

  • | ACOUSTIC EMISSION TESTING (AET) - IN-SERVICE BOTTOM INTEGRITY SCREENING |
  • | |
  • | Tank Shell Plate |
  • | | | |
  • | | [PZT Sensor] <== High-frequency piezoelectric transducers detect stress waves |
  • | | | |
  • | | | |
  • | | | Liquid Product Column (Transmits Acoustic Waves) |
  • | =====|===|======================================================================== |
  • | |
  • | * * * (1) Active Rust Scale Cracking ===> Acoustic Stress Waves (* * *) |
  • | / |
  • | [Corrosion Pit] |
  • | |
  • | (~) (~) (2) Pinhole Fluid Leakage ===> Turbulent Jet Acoustic Noise (~ ~) |
  • | / |
  • | [Perforation] |
  • +-----------------------------------------------------------------------------------------+

Physical Phenomenon Detected: AET does not introduce external acoustic energy; it "listens" to microscopic elastic stress waves emitted by two distinct active mechanisms:

Active Corrosion: Brittle iron oxide scale (rust platelets) on the soil-side of the bottom plate micro-fractures and delaminates under cyclic floor flexing, releasing transient high-frequency burst acoustic signals (100 to 300 kHz).

Active Fluid Leakage: Product escaping through a pinhole perforation under hydrostatic head creates turbulent, continuous fluid-jet acoustic emissions.

Sensor Array: Highly sensitive piezoelectric transducers are mounted circumferentially around the exterior of the lower shell course in acoustic couplant.

Operational Testing Protocol: The tank is tested in-service during a stabilized holding period. Pumps, agitators, and heating coils are isolated to eliminate background mechanical noise. Sensor arrival-time differentials triangulate the precise planar coordinates of acoustic events on the bottom floor.

Integrity Grading: AET classifies tank floor condition into risk categories (e.g., Grade 1: no active damage; Grade 2: minor corrosion; Grade 3: active heavy corrosion/probable leak). This provides operators with objective, data-driven justification for scheduling or deferring expensive out-of-service internal inspections.

Comparison of Leak Detection and Monitoring Methodologies

Technology Detection Target Operational Status Response Time Primary Limitation

Slotted Telltale Pipes Liquid hydrocarbon drainage beneath RPB. Continuous in-service monitoring. Hours to days (gravity flow dependent). Dependent on unblocked pipes; cannot detect vapor-only leaks.

Hydrocarbon Sniff Tubes VOC vapors escaping through floor pinholes. Periodic manual or continuous automated. Rapid for volatile fuels. Ineffective for heavy crude or non-volatile asphalt/lube oils.

Sensor Cable Grids Liquid hydrocarbon contact with interstitial cable. Continuous 24/7 automated SCADA alarm. Minutes from liquid contact. High installation cost; requires complete floor replacement to install.

Acoustic Emission (AET) Active floor corrosion scale cracking and turbulent pinhole leaks. In-service test (tank remains online). Periodic campaign (over 2-24 hours). Qualitative risk grade; cannot measure remaining wall thickness.

Groundwater Wells Dissolved BTEX and free-phase LNAPL plume migration. Periodic sampling (quarterly/semi-annual). Weeks to months (groundwater migration). Contamination has already entered the external environment.