Study guide
8.1 Branch-Circuit Ratings & Required Circuits
Arkansas Journeyman Electrician Exam Study Guide 2026
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Arkansas Exam Overview
1.1 Current Exam Facts 1.2 Arkansas Licensing Pathway & Board Process 1.3 Open-Book Rules & Allowed References 1.4 NEC 2023 Navigation & Lookup Strategy
2 Electrical Theory & Trade Calculations
2.1 Ohm's Law, Power, and Basic Circuits 2.2 Series, Parallel, and Combination Circuits 2.3 Voltage Drop Calculations 2.4 Box Fill Calculations (314.16)
3 Load Calculations (Article 220)
3.1 Standard Dwelling Unit Load Calculations 3.2 Optional Dwelling & Multifamily Demand 3.3 Commercial / Non-Dwelling Demand Factors 3.4 Ampacity Adjustment & Correction (310.15)
4 Grounding Electrode Systems
4.1 Grounding Electrode Types & Installation 4.2 Grounding Electrode Conductor Sizing (250.66) 4.3 Main Bonding Jumper & Service Bonding
5 Equipment Grounding & Bonding
5.1 Equipment Grounding Conductors (250.122) 5.2 Bonding Raceways, Enclosures & Equipment 5.3 Separately Derived Systems Grounding
6 Services & Service Equipment
6.1 Service Entrance Conductors & Clearances 6.2 Service Disconnecting Means 6.3 Service Equipment & Working Space 6.4 Grounding Connections at the Service
7 Feeders & Overcurrent Protection
7.1 Feeder Conductor Sizing 7.2 Overcurrent Device Selection (Art 240) 7.3 Feeder and Branch-Circuit Tap Rules 7.4 Continuous Loads & OCPD Sizing
8 Branch Circuits, GFCI & AFCI
8.1 Branch-Circuit Ratings & Required Circuits 8.2 Dwelling Receptacle Placement & Kitchen/Bath Circuits 8.3 GFCI Protection Requirements 8.4 AFCI Protection Requirements
9 Metal Raceways
9.1 EMT Installation & Supports 9.2 RMC and IMC 9.3 Flexible Metal & Liquidtight Flexible Metal Conduit
10 Nonmetallic Raceways & Enclosures
10.1 PVC and ENT 10.2 Conduit Fill (Chapter 9 Tables) 10.3 Boxes, Conduit Bodies & Fill 10.4 Cabinets, Cutout Boxes & Meter Enclosures
11 Conductor Ampacity & Selection
11.1 Ampacity Table 310.16 Application 11.2 Termination Temperature Limitations 11.3 Conductor Insulation Types & Uses 11.4 Parallel Conductors
12 Cable Assemblies & Terminations
12.1 NM, MC, and AC Cable Assemblies 12.2 Conductor Identification & Color Coding 12.3 Splices, Taps & Terminations
13 Motors (Article 430)
13.1 Motor Nameplate Data & FLC Tables 13.2 Motor Branch-Circuit Conductors 13.3 Motor Overload Protection 13.4 Motor Short-Circuit / Ground-Fault Protection
14 Motor Controls & Transformers
14.1 Motor Disconnects & Controllers 14.2 Motor Control Circuits 14.3 Transformers (Article 450) for Journeymen
15 Utilization & General-Use Equipment
15.1 Luminaires & Lighting (Art 410) 15.2 Receptacles & Switches (Arts 406/404) 15.3 Appliances & Fixed Electric Space-Heating 15.4 Panelboards (Art 408)
16 Special Occupancies
16.1 Hazardous (Classified) Locations Overview 16.2 Health Care, Assembly & Temporary Installations 16.3 Swimming Pools, Spas & Similar Installations
17 Special Equipment Highlights
17.1 Signs & Outline Lighting 17.2 Elevators & Electric Vehicle Power Transfer 17.3 Emergency & Standby Systems Basics
18 Low-Voltage, Alarms & Communications
18.1 Class 1, 2, and 3 Circuits (Art 725) 18.2 Fire Alarm Systems (Art 760) 18.3 Communications Circuits Overview (Art 800+)
19 Electrical Safety
19.1 Working Space & Dedicated Equipment Space (110.26) 19.2 Lockout/Tagout & Safe Work Practices 19.3 Arc-Flash Awareness for the Exam
20 Exam Strategy & Test Day
20.1 Mixed Calculation Lab 20.2 Timed Code Lookup Drills 20.3 Test-Day Checklist, Scoring & Retakes
8.1 Branch-Circuit Ratings & Required Circuits
Key Takeaways Explain This Topic AI
A branch circuit begins at the final overcurrent device protecting the circuit and ends at the outlets or utilization equipment it supplies (Article 100 / Article 210).
NEC 210.11(C) requires dwelling small-appliance (two or more 20 A), laundry (one 20 A), bathroom receptacle (one 20 A), and garage receptacle (one 20 A) circuits in addition to general lighting/receptacle circuits.
Conductors and overcurrent devices for continuous loads are sized at not less than 125% of the continuous load under 210.19 and 210.20 unless an exception applies.
Multiwire branch circuits under 210.4 must have simultaneous disconnection of all ungrounded conductors at the originating panelboard or similar location.
On the Arkansas Prov JW exam (NEC 2023, 60Q/3 hr/70%), required-circuit and rating stems map to Article 210 Parts I–II — tab 210.11, 210.19, 210.20, and 210.23.
Last updated: August 2026
Why Branch-Circuit Ratings Matter on the Arkansas JW Exam
The Arkansas Journeyman Electrician exam (Prov / ADLL Board of Electrical Examiners, NEC 2023 , 60 questions, 3 hours, 70% pass) weights Service, Feeders, Branch Feeders and Overcurrent Protection at 8 items . A large share of those stems land in Article 210 . This section covers branch-circuit identity, ratings, conductor/OCPD sizing, multiwire rules, and the dwelling required circuits in 210.11 . Receptacle placement follows in §8.2; GFCI and AFCI personnel/fire protection follow in §§8.3–8.4.
On an open-book form, Prov will not ask you to memorize every Exception — but you will lose time if you cannot tell a branch circuit from a feeder , or if you confuse a small-appliance branch circuit with a general lighting circuit. Tab Article 210 Parts I–II , especially 210.4 , 210.11 , 210.19 , 210.20 , 210.21 , and 210.23 , before exam day.
Branch-Circuit Boundary (Article 100 + Article 210)
A branch circuit consists of the circuit conductors between the final overcurrent device protecting the circuit and the outlet(s). Everything upstream of that final OCPD is typically a feeder or service conductor path. Exam stems often hide the boundary behind language about panelboards, subpanels, and equipment disconnects — locate the last overcurrent device ahead of the load before choosing an Article 210 rule.
- Term Practical meaning for Article 210
- Branch circuit Conductors from final OCPD to outlets/equipment
- Individual branch circuit Supplies only one utilization equipment
Multiwire branch circuit Two or more ungrounded conductors with a shared neutral, with voltage between ungrounded conductors and from each ungrounded conductor to the neutral
General-purpose branch circuit Supplies two or more receptacles or outlets for lighting and appliances
Appliance branch circuit Supplies energy to one or more outlets for appliances; no permanently connected lighting other than as permitted
Branch-Circuit Ratings and Permissible Loads
210.3 identifies branch circuits by the maximum rating or setting of the overcurrent device. Common dwelling ratings are 15 A and 20 A for lighting/receptacle circuits; 30 A , 40 A , and 50 A appear for ranges, dryers, and similar equipment circuits. Match the OCPD rating to the conductor ampacity and to the outlet device rules in 210.21 .
210.23 limits what a given rating may supply:
A 15 A or 20 A branch circuit may supply lighting units, utilization equipment, or a combination of both within the section’s load limits.
Cord-and-plug connected utilization equipment on a 15 A or 20 A circuit generally must not exceed 80% of the branch-circuit rating when the equipment is not fastened in place (and similar percentage rules apply for fastened-in-place equipment sharing the circuit — read the exact subsection in the stem).
Higher-rated circuits (30 A, 40 A, 50 A) have narrower permitted load types; do not assume a 30 A circuit can freely supply general lighting.
Exam trap: a stem that says “20 A small-appliance circuit” is pointing at 210.11(C)(1) / 210.52(B) , not at a general 20 A bedroom circuit.
Conductor and OCPD Sizing (210.19 / 210.20)
210.19(A) requires branch-circuit conductors to have an ampacity not less than the maximum load to be served. Where a branch circuit supplies continuous loads or any combination of continuous and noncontinuous loads, the minimum conductor ampacity is not less than the noncontinuous load plus 125% of the continuous load (with listed exceptions for certain assemblies).
210.20(A) applies the same 125% continuous-load logic to the branch-circuit overcurrent device. Continuous load is generally a load expected to continue for 3 hours or more (Article 100). Lighting in many commercial spaces and some dwelling fixed loads can trigger this — read the stem’s duration language.
Practical open-book method:
Identify continuous vs noncontinuous portions of the load.
Size conductors and OCPD at noncontinuous + 1.25 × continuous (unless an exception applies).
Verify termination temperature and ampacity adjustments in Article 310 / 110.14(C) if the stem gives ambient or bundling data (covered in other chapters).
Multiwire Branch Circuits (210.4)
Multiwire branch circuits share a neutral among two or more ungrounded conductors. 210.4(B) requires that each multiwire branch circuit be provided with a means that simultaneously disconnects all ungrounded conductors at the point where the branch circuit originates (typically a handle-tied or multipole breaker). 210.4(D) requires grouping of the ungrounded and grounded conductors of each multiwire circuit in the same raceway or cable where they originate.
Prov items love the simultaneous-disconnect rule: if a stem describes opening only one ungrounded conductor of a multiwire circuit while leaving the other energized on a shared neutral, the installation violates 210.4(B) .
Dwelling Required Circuits — 210.11(C)
Beyond circuits sized for the Article 220 calculated load, 210.11(C) adds dwelling-unit minimums that appear constantly on journeyman exams:
Requirement Rule Rating / notes
Small-appliance 210.11(C)(1) Two or more 20 A small-appliance branch circuits for kitchen/dining/pantry/similar receptacle outlets per 210.52(B)
Laundry 210.11(C)(2) At least one 20 A branch circuit for laundry receptacle outlet(s) per 210.52(F) ; no other outlets generally
Bathroom 210.11(C)(3) At least one 20 A branch circuit to supply bathroom receptacle outlet(s); may supply other bathroom loads in the same bathroom(s) as permitted
Garage 210.11(C)(4) At least one 20 A branch circuit to supply receptacle outlet(s) required by 210.52(G) in attached garages and in detached garages with electric power
210.11(A)–(B) still require enough branch circuits for the total calculated load and reasonably proportional distribution among panelboard circuits. Do not stop at the four specialty circuits and forget general lighting/receptacle load.
Small-appliance circuits must not supply lighting outlets or receptacles outside the kitchen/dining/breakfast/pantry/similar areas (with narrow exceptions such as a clock outlet or certain supplementary receptacles — check 210.52(B)(2) Exceptions when the stem cites them). Laundry and bathroom required circuits likewise have “no other outlets” / limited-outlet rules that Prov loves to twist.
Arkansas Exam Workflow
When a stem asks “how many 20 A circuits are required minimum for …,” inventory 210.11(C) first, then add circuits demanded by the load calculation and by dedicated equipment. When a stem asks about continuous-load conductor size, go to 210.19 / 210.20 , not Article 220 demand factors. When a stem mentions a shared neutral and single-pole breakers without handle ties, open 210.4(B) .
Key Takeaways
Branch circuits start at the final OCPD — feeders and service conductors use different Articles.
Continuous loads drive 125% conductor and OCPD sizing under 210.19 / 210.20 .
Dwelling units need ≥2 small-appliance, 1 laundry, 1 bathroom, and 1 garage 20 A circuits under 210.11(C) .
Multiwire circuits require simultaneous disconnection of all ungrounded conductors.