Study guide
10.4 Cabinets, Cutout Boxes & Meter Enclosures
Arkansas Journeyman Electrician Exam Study Guide 2026
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Arkansas Exam Overview
1.1 Current Exam Facts 1.2 Arkansas Licensing Pathway & Board Process 1.3 Open-Book Rules & Allowed References 1.4 NEC 2023 Navigation & Lookup Strategy
2 Electrical Theory & Trade Calculations
2.1 Ohm's Law, Power, and Basic Circuits 2.2 Series, Parallel, and Combination Circuits 2.3 Voltage Drop Calculations 2.4 Box Fill Calculations (314.16)
3 Load Calculations (Article 220)
3.1 Standard Dwelling Unit Load Calculations 3.2 Optional Dwelling & Multifamily Demand 3.3 Commercial / Non-Dwelling Demand Factors 3.4 Ampacity Adjustment & Correction (310.15)
4 Grounding Electrode Systems
4.1 Grounding Electrode Types & Installation 4.2 Grounding Electrode Conductor Sizing (250.66) 4.3 Main Bonding Jumper & Service Bonding
5 Equipment Grounding & Bonding
5.1 Equipment Grounding Conductors (250.122) 5.2 Bonding Raceways, Enclosures & Equipment 5.3 Separately Derived Systems Grounding
6 Services & Service Equipment
6.1 Service Entrance Conductors & Clearances 6.2 Service Disconnecting Means 6.3 Service Equipment & Working Space 6.4 Grounding Connections at the Service
7 Feeders & Overcurrent Protection
7.1 Feeder Conductor Sizing 7.2 Overcurrent Device Selection (Art 240) 7.3 Feeder and Branch-Circuit Tap Rules 7.4 Continuous Loads & OCPD Sizing
8 Branch Circuits, GFCI & AFCI
8.1 Branch-Circuit Ratings & Required Circuits 8.2 Dwelling Receptacle Placement & Kitchen/Bath Circuits 8.3 GFCI Protection Requirements 8.4 AFCI Protection Requirements
9 Metal Raceways
9.1 EMT Installation & Supports 9.2 RMC and IMC 9.3 Flexible Metal & Liquidtight Flexible Metal Conduit
10 Nonmetallic Raceways & Enclosures
10.1 PVC and ENT 10.2 Conduit Fill (Chapter 9 Tables) 10.3 Boxes, Conduit Bodies & Fill 10.4 Cabinets, Cutout Boxes & Meter Enclosures
11 Conductor Ampacity & Selection
11.1 Ampacity Table 310.16 Application 11.2 Termination Temperature Limitations 11.3 Conductor Insulation Types & Uses 11.4 Parallel Conductors
12 Cable Assemblies & Terminations
12.1 NM, MC, and AC Cable Assemblies 12.2 Conductor Identification & Color Coding 12.3 Splices, Taps & Terminations
13 Motors (Article 430)
13.1 Motor Nameplate Data & FLC Tables 13.2 Motor Branch-Circuit Conductors 13.3 Motor Overload Protection 13.4 Motor Short-Circuit / Ground-Fault Protection
14 Motor Controls & Transformers
14.1 Motor Disconnects & Controllers 14.2 Motor Control Circuits 14.3 Transformers (Article 450) for Journeymen
15 Utilization & General-Use Equipment
15.1 Luminaires & Lighting (Art 410) 15.2 Receptacles & Switches (Arts 406/404) 15.3 Appliances & Fixed Electric Space-Heating 15.4 Panelboards (Art 408)
16 Special Occupancies
16.1 Hazardous (Classified) Locations Overview 16.2 Health Care, Assembly & Temporary Installations 16.3 Swimming Pools, Spas & Similar Installations
17 Special Equipment Highlights
17.1 Signs & Outline Lighting 17.2 Elevators & Electric Vehicle Power Transfer 17.3 Emergency & Standby Systems Basics
18 Low-Voltage, Alarms & Communications
18.1 Class 1, 2, and 3 Circuits (Art 725) 18.2 Fire Alarm Systems (Art 760) 18.3 Communications Circuits Overview (Art 800+)
19 Electrical Safety
19.1 Working Space & Dedicated Equipment Space (110.26) 19.2 Lockout/Tagout & Safe Work Practices 19.3 Arc-Flash Awareness for the Exam
20 Exam Strategy & Test Day
20.1 Mixed Calculation Lab 20.2 Timed Code Lookup Drills 20.3 Test-Day Checklist, Scoring & Retakes
10.4 Cabinets, Cutout Boxes & Meter Enclosures
Key Takeaways Explain This Topic AI
Article 312 governs cabinets, cutout boxes, and meter socket enclosures—installation, wiring space, and enclosure integrity for overcurrent devices and metering
Cabinets and cutout boxes must be installed in dry locations unless listed for the environment; doors/covers must be tight and suitable for wet or outdoor exposure when used there
Wire-bending space at terminals follows 312.6 and related tables—insufficient bending space is a common service and feeder enclosure failure
Unused openings must be effectively closed; bushings protect conductor insulation where raceways enter
Meter enclosures and socket bases must remain accessible for utility and inspection; bonding/grounding of meter cans ties back to Articles 250 and service rules
Last updated: August 2026
10.4 Cabinets, Cutout Boxes & Meter Enclosures
Quick Answer: Article 312 covers cabinets , cutout boxes , and meter socket enclosures . Install them dry unless listed/identified for damp or wet locations; keep covers and doors complete; close unused openings; provide wire-bending space at terminals per 312.6 ; and treat meter enclosures as part of the service equipment chain that still must meet grounding/bonding and accessibility rules.
On Arkansas Prov, Raceways and Enclosures items do not stop at conduit straps. PVC and ENT land in cabinets; services land in meter sockets; feeders land in cutout boxes. Article 312 is where enclosure installation quality is tested—especially bending space, wet-location suitability, and “open knockout left unplugged” workmanship failures.
Definitions that matter on stems
- Term Exam meaning
- Cabinet Enclosure with a framed door for devices mounted on a backboard or rails (typical panelboard cabinet)
- Cutout box Enclosure with a hinged or removable cover for surface mounting of devices
- Meter socket enclosure Enclosure that holds the utility meter socket / metering equipment
Do not confuse Article 312 cabinets with Article 408 panelboard internals or Article 314 outlet boxes. A device box is 314 ; the steel can around a loadcenter is a cabinet under 312 (with panelboard rules in 408 still applying to the bus/assembly).
Installation environment — damp, wet, and outdoor
312.2 requires cabinets and cutout boxes to be installed in dry spaces unless listed for the location. Outdoor meter cans and rainproof panel cabinets must be listed/identified for damp or wet locations as appropriate. Using an indoor NEMA 1 enclosure outdoors is a classic fail.
Mounting surfaces must be true; gaps that admit moisture behind outdoor enclosures defeat the listing. Raceway entries into wet-location cabinets need fittings listed for wet locations (raintight hubs, etc.)—the same lesson as wet-location EMT connectors, now applied at the enclosure.
Position, accessibility, and working space
Cabinets and cutout boxes must remain accessible for operation and maintenance. Height and clearance interact with 110.26 working space in front of electrical equipment: you can satisfy Article 312 mounting and still fail working-space depth/width/height. Prov may blend “enclosure” language with clear-space dimensions—open 110.26 when the stem is about standing room in front of a panel, and 312 when the stem is about the can itself (doors, openings, bending space).
Doors must be able to open adequately. Enclosures installed in paths of vehicles or subject to physical damage need protection—coordinate with the raceway physical-damage rules you already studied for PVC Schedule 80 and RMC.
Wire-bending space — 312.6 (high yield)
Conductors entering cabinets and cutout boxes need room to bend to terminals without damage. 312.6 sets minimum wire-bending space at terminals, with tables based on conductor size and whether conductors enter opposite the terminal or from another wall.
Why Prov asks this
Service and feeder lugs on 3/0, 4/0, and 250 kcmil conductors need surprisingly deep gutters. Undersized cabinets, side-fed panels without adequate side bending space, or conductors forced into sharp bends violate 312.6 even when ampacity and conduit fill are perfect.
Worked examples
Example A: A panelboard cabinet is side-wired with 4/0 AWG copper feeders landing on main lugs. Open 312.6 tables for the minimum bending space for that conductor size and entry orientation. If the cabinet’s gutter is smaller than the table value, the installation fails—choose a different entry, a larger enclosure, or rearrangements permitted by the section.
Example B: Meter socket enclosure with large service-entrance conductors. Bending space and terminal space still apply; utility standards may add requirements, but the NEC baseline remains Article 312 plus service Articles 230 / 250 .
Example C: Control cabinet with only 14 AWG and 12 AWG. Bending-space tables are less dramatic, but cluttered wireways and violated gutter space still matter under enclosure and industrial control standards referenced by the Code.
Spacing, barriers, and overcurrent devices
Cabinets housing overcurrent devices must maintain required spacing and use barriers where the assembly listing and Articles 312 / 408 demand separation of different systems or voltages. Live parts must be guarded when doors are open per general rules in Article 110 . On exam stems about “cabinet for a panelboard,” expect overlap: 312 for the box, 408 for the panelboard, 110 for working space and guarding.
Unused openings and conductor protection
312.5 (and related enclosure rules) require unused openings to be effectively closed to provide substantially equivalent protection. Open knockouts are not “future expansion”—they are Code defects that admit debris and fingers.
Where conductors enter through raceways, provide bushings or equivalent protection so insulation is not abraded on sharp metal. Nonmetallic raceways into metal cabinets still need proper connectors; the wire-type EGC must bond the metal cabinet when PVC/ENT supply the run ( 250 bonding).
Cables entering cabinets must be secured and supported; NM and other cables have Article 312 and Chapter 3 securement interactions—follow the wiring-method article plus enclosure entry rules.
Meter enclosures — practical exam points
Meter socket enclosures are specifically recognized in Article 312 . Key journeyman expectations:
Enclosure listed/identified for the outdoor/wet location when used as a service meter can.
Working space and accessibility for utility sealing, meter installation, and inspection.
Bonding of the meter enclosure as required for service equipment—often tied to the grounded conductor bonding means at the service disconnect / meter-main arrangements in Articles 230 and 250 .
Raceway hubs and connectors suitable for the weatherproof integrity of the can.
Line and load barriers or compartment rules when the listing requires them (meter-mains).
Arkansas services frequently use outdoor meter-main combinations. When a Prov stem mentions the meter can on PVC or rigid risers, check three layers: raceway article (352/344), enclosure article ( 312 ), and service grounding ( 250 ).
Cutout boxes vs cabinets on the job
Cutout boxes are common for fused switches and small surface equipment. They need covers that stay in place, adequate bending/gutter space, and environment suitability. Do not use a shallow cutout box where 312.6 bending space for large conductors cannot be met—upsizing the enclosure is the Code fix, not forcing conductors.
Interaction with nonmetallic raceways (chapter tie-in)
This chapter’s PVC and ENT rules meet Article 312 at every termination:
Fasten the raceway within 3 ft of the cabinet ( 352.30 / 362.30 ).
Use listed connectors suitable for the enclosure and location.
Close unused openings in the cabinet.
Land the wire-type EGC on the enclosure grounding terminal.
Verify bending space for the conductors inside ( 312.6 ).
If temperature swing is large on a PVC riser into a meter can, remember 352.44 expansion fittings so the enclosure bushings are not levered by conduit movement.
That multi-article chain is how open-book exams build multi-step Raceways items.
Common Prov traps
- Trap Correct move
- Indoor cabinet outdoors Need wet/damp location listing
- Open knockout left open Effectively close unused openings
- Ignoring bending space on 4/0 lugs Apply 312.6 tables
- Treating meter can as exempt from bonding Apply service/ 250 bonding rules
- Confusing 312 cabinets with 314 device boxes Different articles, different fill rules
- PVC into metal cabinet without EGC Pull and land wire-type EGC
- Timed open-book tips
Tab 312.2 , 312.5 , 312.6 (and its tables), plus cross-tabs to 110.26 , 230 , and 250 for service meter cans. Decision tree: (1) Is the enclosure suitable for dry/damp/wet? (2) Are openings closed and entries bushed? (3) Is wire-bending space adequate for the conductor size and entry direction? (4) Is the metal enclosure bonded when fed by nonmetallic raceway? Clear those four checks and Article 312 items among the eight Raceways and Enclosures questions become routine points on the Arkansas Prov Journeyman exam.