Study guide

16.3 Swimming Pools, Spas & Similar Installations

Arkansas Journeyman Electrician Exam Study Guide 2026

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Arkansas Exam Overview

1.1 Current Exam Facts 1.2 Arkansas Licensing Pathway & Board Process 1.3 Open-Book Rules & Allowed References 1.4 NEC 2023 Navigation & Lookup Strategy

2 Electrical Theory & Trade Calculations

2.1 Ohm's Law, Power, and Basic Circuits 2.2 Series, Parallel, and Combination Circuits 2.3 Voltage Drop Calculations 2.4 Box Fill Calculations (314.16)

3 Load Calculations (Article 220)

3.1 Standard Dwelling Unit Load Calculations 3.2 Optional Dwelling & Multifamily Demand 3.3 Commercial / Non-Dwelling Demand Factors 3.4 Ampacity Adjustment & Correction (310.15)

4 Grounding Electrode Systems

4.1 Grounding Electrode Types & Installation 4.2 Grounding Electrode Conductor Sizing (250.66) 4.3 Main Bonding Jumper & Service Bonding

5 Equipment Grounding & Bonding

5.1 Equipment Grounding Conductors (250.122) 5.2 Bonding Raceways, Enclosures & Equipment 5.3 Separately Derived Systems Grounding

6 Services & Service Equipment

6.1 Service Entrance Conductors & Clearances 6.2 Service Disconnecting Means 6.3 Service Equipment & Working Space 6.4 Grounding Connections at the Service

7 Feeders & Overcurrent Protection

7.1 Feeder Conductor Sizing 7.2 Overcurrent Device Selection (Art 240) 7.3 Feeder and Branch-Circuit Tap Rules 7.4 Continuous Loads & OCPD Sizing

8 Branch Circuits, GFCI & AFCI

8.1 Branch-Circuit Ratings & Required Circuits 8.2 Dwelling Receptacle Placement & Kitchen/Bath Circuits 8.3 GFCI Protection Requirements 8.4 AFCI Protection Requirements

9 Metal Raceways

9.1 EMT Installation & Supports 9.2 RMC and IMC 9.3 Flexible Metal & Liquidtight Flexible Metal Conduit

10 Nonmetallic Raceways & Enclosures

10.1 PVC and ENT 10.2 Conduit Fill (Chapter 9 Tables) 10.3 Boxes, Conduit Bodies & Fill 10.4 Cabinets, Cutout Boxes & Meter Enclosures

11 Conductor Ampacity & Selection

11.1 Ampacity Table 310.16 Application 11.2 Termination Temperature Limitations 11.3 Conductor Insulation Types & Uses 11.4 Parallel Conductors

12 Cable Assemblies & Terminations

12.1 NM, MC, and AC Cable Assemblies 12.2 Conductor Identification & Color Coding 12.3 Splices, Taps & Terminations

13 Motors (Article 430)

13.1 Motor Nameplate Data & FLC Tables 13.2 Motor Branch-Circuit Conductors 13.3 Motor Overload Protection 13.4 Motor Short-Circuit / Ground-Fault Protection

14 Motor Controls & Transformers

14.1 Motor Disconnects & Controllers 14.2 Motor Control Circuits 14.3 Transformers (Article 450) for Journeymen

15 Utilization & General-Use Equipment

15.1 Luminaires & Lighting (Art 410) 15.2 Receptacles & Switches (Arts 406/404) 15.3 Appliances & Fixed Electric Space-Heating 15.4 Panelboards (Art 408)

16 Special Occupancies

16.1 Hazardous (Classified) Locations Overview 16.2 Health Care, Assembly & Temporary Installations 16.3 Swimming Pools, Spas & Similar Installations

17 Special Equipment Highlights

17.1 Signs & Outline Lighting 17.2 Elevators & Electric Vehicle Power Transfer 17.3 Emergency & Standby Systems Basics

18 Low-Voltage, Alarms & Communications

18.1 Class 1, 2, and 3 Circuits (Art 725) 18.2 Fire Alarm Systems (Art 760) 18.3 Communications Circuits Overview (Art 800+)

19 Electrical Safety

19.1 Working Space & Dedicated Equipment Space (110.26) 19.2 Lockout/Tagout & Safe Work Practices 19.3 Arc-Flash Awareness for the Exam

20 Exam Strategy & Test Day

20.1 Mixed Calculation Lab 20.2 Timed Code Lookup Drills 20.3 Test-Day Checklist, Scoring & Retakes

16.3 Swimming Pools, Spas & Similar Installations

Key Takeaways Explain This Topic AI

Article 680 covers swimming pools, spas, hot tubs, fountains, and similar installations—bonding and GFCI rules are the Arkansas JW high-yield core

Equipotential bonding (680.26 family) ties conductive pool structures, forming shells, metal fittings, and prescribed perimeter surfaces into a low-voltage-gradient grid

Pool equipment grounding still follows equipment grounding conductor rules; bonding and grounding are related but not interchangeable terms on exam stems

GFCI protection is required for many pool pump motors, pool receptacles, and spa/hot tub equipment—open the specific 680 Part for the installation type

Clearances for overhead conductors, receptacle placement distances, and underwater luminaire rules are frequent open-book lookup items—tab the figures and distance tables

Last updated: August 2026

16.3 Swimming Pools, Spas & Similar Installations

Quick Answer: Article 680 is the pool/spa Code home. For Arkansas Prov Journeyman (NEC 2023 , 60Q / 3 hr / 70%), prioritize equipotential bonding , equipment grounding , and GFCI requirements, then learn the common distance rules for receptacles and overhead conductors. Bonding equalizes voltage gradients in the pool area; GFCI protects people from ground faults on pool equipment and receptacles—both can appear in one stem.

Pools kill and injure when fault voltage appears in water or on wet decks. Article 680’s bonding grid and GFCI rules exist to keep touch potentials low and to clear ground faults quickly. Special Occupancies and Equipment is only 4 items on the Prov outline, but pool questions are classic because the rules are specific and look-uppable.

Scope — what Article 680 covers

680 applies to the construction and installation of electrical wiring for and equipment in or adjacent to swimming pools, spas, hot tubs, fountains, and similar installations, including permanently installed and storable types as defined in the article. Parts of 680 specialize:

  • General requirements (wiring methods, GFCI, clearances)
  • Permanently installed pools
  • Storable pools
  • Spas and hot tubs
  • Fountains
  • Pools and tubs for therapeutic use / hydromassage bathtubs (as scoped)

Exam habit: Identify the Part from the equipment named (spa vs permanently installed pool vs storable pool) before applying a rule from the wrong Part.

Grounding vs bonding at pools (do not swap them)

Concept Job at a pool

Equipment grounding Provides a low-impedance path back to the source so OCPDs clear ground faults on pump motors, heaters, luminaires, and panels

Equipotential bonding Ties conductive parts and prescribed deck/perimeter elements together so voltage gradients in the pool/spa area stay small

You typically need both . A solid EGC does not replace the bonding grid. A bonding grid does not replace the EGC to the panel. Prov stems that say “bonding conductor” want 680 bonding answers; stems that say “equipment grounding conductor” want EGC sizing/path answers (often Table 250.122 via the pool equipment circuit, with 680’s special notes).

Equipotential bonding — 680.26 (high yield)

For permanently installed pools, 680.26 (equipotential bonding) is the section to tab. Core ideas:

What gets bonded

Typical bonded elements (confirm exact list in your NEC):

Conductive pool shells (rebar/copper grid in concrete pools; other shells as specified)

Perimeter surfaces within the prescribed distance of the pool (equipotential bonding of the deck/patio zone—follow the current Code’s copper conductor / reinforcing steel options)

  • Metal forming shells and mounting brackets for wet-niche luminaires
  • Metal fittings within or attached to the pool structure

Metal parts of electrical equipment associated with the pool water circulating system (motors, heaters, etc., as required)

Metal raceways , piping, and fixed metal parts within specified distances of the inside pool walls (with exceptions for certain isolated parts and double-insulated equipment)

Bonding conductor characteristics

The bonding conductor is commonly required to be solid copper of a minimum size stated in 680 (often 8 AWG solid copper for the bonding conductor— verify in the 2023 text you bring to Prov). Connections must be listed for the purpose and suitable for the environment (wet, corrosive). Brass/bronze clamps listed for pool bonding are field standards; sheet-metal screws are not a bonding plan.

Double-insulated motors

Double-insulated pool pump motors generally do not require an equipment grounding conductor in the same way ordinary motors do, and bonding rules interact carefully—open the double-insulated equipment provisions rather than forcing a green wire onto equipment designed without an EGC terminal.

Water bonding

Where required, pool water itself is bonded through listed means (conductive fittings or other methods recognized in 680) so the water remains in the equipotential plane.

Worked thinking: A concrete pool with steel reinforcing: bond the rebar cage into the equipotential bonding network, bond the perimeter surface method required by 680.26, bond metal niche shells and circulating equipment, and land bonding connections with listed clamps. Separately, run the circuit EGC with the pump feeder/branch circuit to the equipment grounding terminal (unless double-insulated rules apply).

GFCI protection — people protection around water

GFCI requirements appear throughout 680 for pool pump motors, pool equipment, receptacles near pools, spa equipment, and underwater luminaires (as applicable by Part). High-yield patterns:

Pool pump motors for permanently installed pools generally require GFCI protection (open the exact motor/outlet sections for voltage and scope).

Receptacles near pools have both placement distance rules and GFCI rules—meeting one does not waive the other.

Spas and hot tubs have strong GFCI mandates for equipment and often for the entire spa package.

Storable pools lean heavily on GFCI-protected cords/equipment.

Exam trap: Answering “bond it” when the stem asks how personnel are protected from line-to-ground shock on a pool pump—bonding helps gradients; GFCI is the personnel ground-fault protective device the stem usually wants when it asks about shock protection on the equipment circuit.

Receptacle placement and other distance rules

Article 680 specifies minimum distances from pool walls for receptacles, and requires at least one receptacle in a certain band for permanently installed pools (so cords are not stretched across wet decks from distant outlets). Overhead service and feeder conductor clearances above pools and diving structures are strict—tab the clearance table/figure in 680 rather than using ordinary 230 clearance memory.

Switching devices and other utilization equipment also have location restrictions relative to the pool. Underwater luminaires have wet-niche vs dry-niche vs no-niche rules, forming-shell bonding, and GFCI/isolation requirements—open those subsections when the stem names a wet-niche light.

Wiring methods near pools

Flexible cords for fixed pool equipment are limited; underground wiring near pools has burial and raceway constraints; branch circuits for pool equipment often require insulated EGCs of copper and wiring methods suited to wet/corrosive environments. Do not treat a pool pump circuit like a dry indoor branch circuit.

Spas, hot tubs, and indoor units

Spas/hot tubs follow 680 Parts dedicated to them. Outdoor spas share many bonding/GFCI themes with pools. Indoor spas may have modified bonding requirements when certain conditions are met (for example, listed self-contained units on tiled floors with GFCI protection— read the exceptions ). Never assume outdoor pool bonding automatically applies identically to a listed indoor spa package without opening the spa Part.

Hydromassage bathtubs (whirlpool tubs) are often treated in a related 680 Part with GFCI protection for the motor and accessibility of the tub equipment—another “named equipment → correct Part” lookup.

Common Prov pool traps

  • Trap Correct move
  • Using Table 250.66 for a pool bonding conductor Open 680 bonding size language
  • Saying bonding replaces GFCI Provide both as required
  • Placing a receptacle too close to the pool wall Check 680 distance rules
  • Forgetting perimeter surface bonding Apply 680.26 perimeter requirements
  • Applying permanently installed pool rules to a storable pool Open the storable Part
  • Arkansas Prov open-book tips

Tab 680.26 (equipotential bonding), the GFCI subsections for pool motors/receptacles, and the receptacle location distance rules. Practice one narrative: “pump circuit = EGC + GFCI; pool structure/deck = equipotential bonding.” That sentence prevents most pool mix-ups on Special Occupancies items. Combined with Articles 500-series, 517, 518, and 590, you now have a complete map for the Prov Special Occupancies and Equipment slice.