Study guide
15.1 Luminaires & Lighting (Art 410)
Arkansas Journeyman Electrician Exam Study Guide 2026
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Arkansas Exam Overview
1.1 Current Exam Facts 1.2 Arkansas Licensing Pathway & Board Process 1.3 Open-Book Rules & Allowed References 1.4 NEC 2023 Navigation & Lookup Strategy
2 Electrical Theory & Trade Calculations
2.1 Ohm's Law, Power, and Basic Circuits 2.2 Series, Parallel, and Combination Circuits 2.3 Voltage Drop Calculations 2.4 Box Fill Calculations (314.16)
3 Load Calculations (Article 220)
3.1 Standard Dwelling Unit Load Calculations 3.2 Optional Dwelling & Multifamily Demand 3.3 Commercial / Non-Dwelling Demand Factors 3.4 Ampacity Adjustment & Correction (310.15)
4 Grounding Electrode Systems
4.1 Grounding Electrode Types & Installation 4.2 Grounding Electrode Conductor Sizing (250.66) 4.3 Main Bonding Jumper & Service Bonding
5 Equipment Grounding & Bonding
5.1 Equipment Grounding Conductors (250.122) 5.2 Bonding Raceways, Enclosures & Equipment 5.3 Separately Derived Systems Grounding
6 Services & Service Equipment
6.1 Service Entrance Conductors & Clearances 6.2 Service Disconnecting Means 6.3 Service Equipment & Working Space 6.4 Grounding Connections at the Service
7 Feeders & Overcurrent Protection
7.1 Feeder Conductor Sizing 7.2 Overcurrent Device Selection (Art 240) 7.3 Feeder and Branch-Circuit Tap Rules 7.4 Continuous Loads & OCPD Sizing
8 Branch Circuits, GFCI & AFCI
8.1 Branch-Circuit Ratings & Required Circuits 8.2 Dwelling Receptacle Placement & Kitchen/Bath Circuits 8.3 GFCI Protection Requirements 8.4 AFCI Protection Requirements
9 Metal Raceways
9.1 EMT Installation & Supports 9.2 RMC and IMC 9.3 Flexible Metal & Liquidtight Flexible Metal Conduit
10 Nonmetallic Raceways & Enclosures
10.1 PVC and ENT 10.2 Conduit Fill (Chapter 9 Tables) 10.3 Boxes, Conduit Bodies & Fill 10.4 Cabinets, Cutout Boxes & Meter Enclosures
11 Conductor Ampacity & Selection
11.1 Ampacity Table 310.16 Application 11.2 Termination Temperature Limitations 11.3 Conductor Insulation Types & Uses 11.4 Parallel Conductors
12 Cable Assemblies & Terminations
12.1 NM, MC, and AC Cable Assemblies 12.2 Conductor Identification & Color Coding 12.3 Splices, Taps & Terminations
13 Motors (Article 430)
13.1 Motor Nameplate Data & FLC Tables 13.2 Motor Branch-Circuit Conductors 13.3 Motor Overload Protection 13.4 Motor Short-Circuit / Ground-Fault Protection
14 Motor Controls & Transformers
14.1 Motor Disconnects & Controllers 14.2 Motor Control Circuits 14.3 Transformers (Article 450) for Journeymen
15 Utilization & General-Use Equipment
15.1 Luminaires & Lighting (Art 410) 15.2 Receptacles & Switches (Arts 406/404) 15.3 Appliances & Fixed Electric Space-Heating 15.4 Panelboards (Art 408)
16 Special Occupancies
16.1 Hazardous (Classified) Locations Overview 16.2 Health Care, Assembly & Temporary Installations 16.3 Swimming Pools, Spas & Similar Installations
17 Special Equipment Highlights
17.1 Signs & Outline Lighting 17.2 Elevators & Electric Vehicle Power Transfer 17.3 Emergency & Standby Systems Basics
18 Low-Voltage, Alarms & Communications
18.1 Class 1, 2, and 3 Circuits (Art 725) 18.2 Fire Alarm Systems (Art 760) 18.3 Communications Circuits Overview (Art 800+)
19 Electrical Safety
19.1 Working Space & Dedicated Equipment Space (110.26) 19.2 Lockout/Tagout & Safe Work Practices 19.3 Arc-Flash Awareness for the Exam
20 Exam Strategy & Test Day
20.1 Mixed Calculation Lab 20.2 Timed Code Lookup Drills 20.3 Test-Day Checklist, Scoring & Retakes
15.1 Luminaires & Lighting (Art 410)
Key Takeaways Explain This Topic AI
A luminaire is a complete lighting unit; Article 410 governs listing, location, support, recessed clearance, and track lighting under NEC 2023.
NEC 410.10(D) creates a 3 ft horizontal by 8 ft vertical zone around bathtubs and showers where pendants, track, cord-connected luminaires, and paddle fans are prohibited.
Clothes-closet luminaires follow 410.16 clearance tables — typically 12 in. for incandescent/LED with exposed lamps above storage and 6 in. for fluorescent/LED surface-mounted luminaires.
Non-Type IC recessed luminaires need ½ in. from combustibles and 3 in. from thermal insulation per 410.116; Type IC fixtures may contact insulation when listed.
Outlet boxes may support luminaires up to 50 lb per 314.27(A); ceiling-suspended paddle fans need listed fan boxes (often 70 lb) under 314.27(C).
Last updated: August 2026
Why Article 410 Matters on the Arkansas JW Exam
Prov’s Arkansas Journeyman outline allocates 6 items to Utilization and General Use Equipment . Lighting questions almost always come from Article 410 (NEC 2023 ), often cross-linked to 314.27 for support and 110.3(B) for listing/instructions. You will not be asked to design decorative layouts — you will be asked whether a pendant may hang over a tub, how far a closet lamp must clear a shelf, whether insulation may touch a recessed can, and how heavy a fixture an outlet box may carry.
Tab 410.10 , 410.16 , 410.115–410.116 , and 410.151 , plus 314.27 . Keep Article 100 definitions handy so you do not confuse a luminaire with a bare lampholder .
Luminaire vs. Lampholder
Article 100 defines a luminaire as a complete lighting unit consisting of a light source together with parts designed to distribute light, position and protect the source, and connect it to the supply. A lampholder is the socket alone. Construction and wiring rules differ: screw-shell lampholders have polarization and voltage limits in 410.50 and related sections, while the bulk of Part II–X applies to complete luminaires. On exam stems that say “fixture,” treat it as a luminaire unless the question clearly means only the socket.
410.6 requires luminaires to be listed . Field-built lighting assemblies are not a journeyman workaround. 110.3(B) then forces you to follow the listing and installation instructions — including wet-location marks and IC ratings.
- Location Rules — 410.10
- Bathtub and Shower Areas — 410.10(D)
Measure a zone 3 feet (900 mm) horizontally and 8 feet (2.5 m) vertically from the top of the bathtub rim or shower stall threshold. Inside that zone, the Code prohibits :
- Cord-connected luminaires
- Chain-, cable-, or cord-suspended luminaires
- Lighting track
- Pendants
- Ceiling-suspended (paddle) fans
Luminaires located within the outside dimensions of the tub or shower space, to a height of 8 feet , must be marked suitable for damp locations — and for wet locations where subject to shower spray. GFCI for bathroom receptacles still lives in 210.8(A) ; do not invent a 410.10(D) GFCI rule for every luminaire unless the listing or another section requires it.
Exam trap: A paddle fan centered over a tub with the blades inside the 3 ft / 8 ft envelope fails 410.10(D) even if the fan is “out of reach” by informal judgment.
Clothes Closets — 410.16
410.16 sets both permitted luminaire types and clearances to the nearest storage-space point (shelf, rod, or similar).
- Luminaire type (typical) Clearance above storage Notes
- Incandescent / LED with completely enclosed lamp 12 in. Surface or recessed as permitted
Incandescent with open/exposed lamp Generally not permitted as closet lighting Use enclosed or fluorescent/LED rules
- Fluorescent / LED surface-mounted 6 in. Common closet answer
- Recessed fluorescent / LED 6 in. Must be listed for the application
Pendents are not the default closet solution. Surface-mounted fluorescent or LED luminaires on the wall or ceiling above the door, clear of the storage cube, are the usual compliant pattern. If a stem asks for the minimum clearance “above the clothes storage,” match the lamp/luminaire type to the table in 410.16 — do not guess from 410.10(D).
Other Location Limits
410.10(A) covers luminaires in damp or wet locations (listed for the environment). 410.10(C) addresses luminaires near combustible material. Outdoor luminaires and under-canopy equipment must carry the correct wet/damp listing — another 110.3(B) enforcement point.
Recessed Luminaires — Thermal Protection & Clearance
410.115 requires thermal protection for many recessed luminaires (with listed exceptions). 410.116 is the clearance workhorse:
Non-Type IC recessed luminaires: maintain not less than ½ inch (12.7 mm) from combustible materials at points other than the support points, and not less than 3 inches (76 mm) from thermal insulation — unless the luminaire is identified for closer spacing.
Type IC (Insulated Ceiling) luminaires: listed for direct contact with thermal insulation and may be installed in contact with combustible materials when so identified.
On the Prov exam, “IC” versus “non-IC” is a binary decision tree. If the stem says insulation will be packed against the housing and the fixture is non-IC, the install fails unless clearance is provided or the fixture is replaced with Type IC.
Support, Outlet Boxes, and Track Lighting
314.27(A) allows a listed outlet box to support a luminaire weighing 50 lb (23 kg) or less, unless the box is listed for a greater weight. Heavier luminaires need independent support or a box listed for the load. 314.27(C) governs boxes for ceiling-suspended (paddle) fans — use a box listed for fan support (commonly marked for 70 lb or the fan’s weight). Never hang a fan from a standard luminaire-only box.
Lighting track (410.151 and following) must be permanently installed, supplied by a branch circuit not exceeding the track’s rating, and loaded so that the connected load does not exceed the rating of the branch circuit and the track. Track is prohibited in the 410.10(D) tub/shower zone and is not a substitute for required general lighting outlets where the Code demands them.
Polarization, Grounding, and Wiring Practice
Luminaires must be wired so the grounded conductor (neutral) lands on the identified terminal (typically the screw-shell of an Edison lampholder) and the ungrounded conductor on the center contact — polarization rules in 410.50 and related text prevent a “hot shell” shock hazard. Metal luminaires generally require equipment grounding per 410.40–410.46 and Article 250 . Flexible cords for luminaires are tightly limited; do not use cord as a substitute for Chapter 3 wiring methods except where 410 expressly allows listed cord-connected luminaires.
Open-book method on exam day: (1) identify environment (closet, tub, insulated ceiling, wet); (2) open the matching 410 subsection; (3) confirm listing marks (IC, wet, damp); (4) check support weight in 314.27 if the stem mentions pounds.
Arkansas Prov Takeaway
Utilization lighting items reward exact section hits, not trade lore. Memorize the 3 ft × 8 ft bathtub envelope, closet 12 in. / 6 in. clearance pattern, non-IC 3 in. insulation clearance, and 50 lb outlet-box luminaire limit — then verify in the 2023 NEC during the 3-hour Prov session.