Study guide
3.2 Peak Cooling Load Calculations: Sensible vs. Latent Heat Gain
Arkansas HVAC/R Contractor License Exam
Track your progress as you read
Finished sections get a check mark.
1 Arkansas HVAC/R Licensing Law, Board Rules & Administration
1.1 Arkansas HVAC/R Board Authority, Statutes & Definitions 1.2 License Classifications & Capacity Limitations 1.3 Registrant Requirements, Apprenticeship & Experience Verification 1.4 License Renewal, Continuing Education & Disciplinary Actions
2 HVAC Thermodynamics, Psychrometrics & Gas Laws
2.1 Principles of Heat Transfer & Thermodynamic Fundamentals 2.2 Psychrometric Chart Dynamics & Air Properties 2.3 Psychrometric Processes & Air Mixture Calculations 2.4 Gas Laws Applied to HVAC/R Systems
3 Heating and Cooling Load Calculations (Manual J & S)
3.1 ACCA Manual J Design Conditions & Thermal Envelopes 3.2 Peak Cooling Load Calculations: Sensible vs. Latent Heat Gain 3.3 Heating Load Calculations & Infiltration Rates 3.4 ACCA Manual S Equipment Selection & Verification
4 Ductwork Design, Sizing & SMACNA Standards (Manual D)
4.1 ACCA Manual D Airflow Fundamentals & External Static Pressure 4.2 Equal Friction & Static Regain Duct Sizing Methods 4.3 Duct Fittings, Equivalent Length & Dynamic Losses 4.4 SMACNA Duct Construction Standards & Joint Sealing
5 Air Distribution, Balancing & Ventilation Codes
5.1 Supply & Return Air Distribution Hardware (Grilles, Registers, Diffusers) 5.2 System Airflow Testing, Adjusting & Balancing (TAB) 5.3 Ventilation Standards: ASHRAE 62.1, 62.2 & 2021 IMC Ventilation Air
6 Mechanical Refrigeration Cycle & Components
6.1 The Vapor-Compression Refrigeration Cycle 6.2 Compressors & Operating Characteristics 6.3 Condensers & Evaporators 6.4 Metering Devices & Refrigerant Flow Controls 6.5 Refrigerant Line Sizing, Oil Return & Field Piping Practices
7 Refrigerants, Oils & EPA Section 608 Regulations
7.1 Refrigerant Chemistry, ASHRAE Standard 34 & A2L Transition 7.2 Lubricating Oils & System Compatibility 7.3 EPA Section 608 Regulatory Mandates & Recovery Standards 7.4 System Evacuation, Dehydration & Leak Detection
8 Air Conditioning & Heat Pump Systems
8.1 Residential & Commercial Split Systems and Package RTUs 8.2 Air-Source Heat Pumps & The Reversing Valve 8.3 Supplemental & Emergency Heating Systems 8.4 Dual-Fuel & Geothermal (Ground-Source) Heat Pump Systems
9 Gas Furnaces, Combustion Air & Venting (IFGC / IMC)
9.1 Gas Furnace Types, AFUE Ratings & Sequence of Operation 9.2 Gas Burners, Ignition Systems & Flame Safeguard Controls 9.3 Combustion Air Requirements (IFGC Chapter 3 / IMC Chapter 7) 9.4 Flue Gas Venting & Category I-IV Venting Systems
10 Boilers, Hydronics & Fuel Gas Piping
10.1 Hydronic Heating Systems, Low-Pressure Boilers & ASME Code 10.2 Hydronic Distribution, Circulator Pumps & Piping Loops 10.3 Fuel Gas Piping Materials, Sizing & Pressure Testing (IFGC Chapter 4) 10.4 Gas Regulators, Manifold Pressure & Gas Meter Sizing 10.5 Condensate Disposal, Piping Support & Mechanical Insulation
11 Electrical Fundamentals, Motors & Control Circuits
11.1 HVAC Electrical Fundamentals, Ohm's Law & Power Calculations 11.2 Single-Phase & Three-Phase Electric Motors in HVAC 11.3 Low-Voltage Control Circuits & Thermostats
12 National Electrical Code (NEC) for HVAC Equipment
12.1 NEC Article 440: Hermetic Refrigerant Motor-Compressors & Branch Circuits 12.2 Equipment Disconnecting Means & Overcurrent Protective Devices (OCPD) 12.3 Motor Branch Circuit Sizing & Conductor Ampacity (NEC Article 430 & Tables)
13 System Maintenance, Troubleshooting & Safety Standards
13.1 Systematic Mechanical & Electrical Troubleshooting 13.2 Airflow & Refrigerant Charge Diagnostics 13.3 Jobsite Safety, OSHA Standards & Personal Protective Equipment
14 Plan Reading, Estimating & HVAC/R Trade Math
14.1 Mechanical Plan Symbols, Schedules & Abbreviations 14.2 Architectural Scales, Dimensions & Quantity Takeoff 14.3 Material, Labor & Bid Estimating 14.4 Applied HVAC/R Trade Math & Unit Conversions
3.2 Peak Cooling Load Calculations: Sensible vs. Latent Heat Gain
Key Takeaways Explain This Topic AI
Total residential cooling load is the mathematical sum of sensible heat gain (which raises dry-bulb air temperature) and latent heat gain (which adds water vapor and raises indoor moisture ratio).
The Sensible Heat Ratio (SHR = Sensible Load / Total Load) in Arkansas typically ranges from 0.70 to 0.80 due to the high ambient summer humidity of Climate Zones 3A and 4A.
Internal sensible loads are governed by occupants (standardized at 230 Btu/h sensible per person with occupancy equal to bedrooms plus one), appliances (1,200 Btu/h kitchen allowance), and lighting (3.412 Btu/h per watt).
Latent infiltration and ventilation loads are calculated using Q_latent = 0.68 * CFM * Delta W_grains, where outdoor air in Arkansas (76°F coincident wet-bulb, ~116 grains/lb) contributes substantial moisture against the indoor 64.6 grains/lb baseline.
Ductwork installed in unconditioned Arkansas attics experiences ambient temperatures exceeding 130°F to 140°F, introducing extreme conductive heat gains and pulling hot, humid air into negative-pressure return plenums if joints are improperly sealed.
Last updated: September 2026
3.2 Peak Cooling Load Calculations: Sensible vs. Latent Heat Gain
Important
The Humid Climate Sizing Imperative : In Arkansas's humid subtropical climate (IECC Climate Zones 3A and 4A), cooling equipment must remove both heat you can measure with a standard thermometer (sensible heat) and moisture suspended in the air (latent heat). If an air conditioner satisfies the sensible thermostat setting too quickly, it shuts down before condensing sufficient moisture off the evaporator coil. This elevates indoor relative humidity above 60%, creating an ideal breeding ground for mold, dust mites, and building envelope rot while leaving occupants feeling clammy.
Under ACCA Manual J 8th Edition, cooling load calculations must strictly separate sensible heat gains from latent heat gains. Each component is derived from distinct thermodynamic drivers, and equipment selection under ACCA Manual S requires matching both the sensible capacity and the latent capacity of the cooling machinery to the calculated building loads.
- Thermodynamic Foundations: Sensible vs. Latent Heat Gain
- Air conditioning in humid environments is a dual-mechanism psychrometric process: TOTAL COOLING LOAD (Q_total)
- ├── SENSIBLE HEAT GAIN (Q_sensible) ---> Elevates Dry-Bulb Temperature (°F)
- │ ├── Opaque envelope conduction (walls, roof, ceiling, floors)
- │ ├── Fenestration conduction & direct solar radiation
- │ ├── Internal sensible loads (occupants, lights, appliances)
- │ ├── Sensible infiltration & mechanical ventilation
- │ └── Duct sensible heat gain in unconditioned spaces
- │
- └── LATENT HEAT GAIN (Q_latent) -------> Adds Water Vapor (Grains of Moisture)
- ├── Internal latent loads (occupant respiration & perspiration)
- ├── Household moisture activities (cooking, bathing, laundry)
- ├── Latent infiltration & ventilation (hot humid outdoor air)
- └── Duct latent leakage in unconditioned spaces
- Sensible Heat Gain Formula
Sensible heat transfer changes the temperature of air without altering its absolute moisture content. The rate of sensible heat gain from moving air is governed by the standard sensible heat formula: Q sensible = 1.08 × CFM × Δ T Q_{\text{sensible}} = 1.08 \times \text{CFM} \times \Delta T Q sensible = 1.08 × CFM × Δ T
Where:
1.08 1.08 1.08 is the sensible heat factor derived from standard air: density ( 0.075 lb/ft 3 ) × specific heat ( 0.24 Btu/(lb ⋅ ∘ F) ) × 60 min/hr = 1.08 \text{density } (0.075 \text{ lb/ft}^3) \times \text{specific heat } (0.24 \text{ Btu/(lb} \cdot ^\circ\text{F)}) \times 60 \text{ min/hr} = 1.08 density ( 0.075 lb/ft 3 ) × specific heat ( 0.24 Btu/(lb ⋅ ∘ F) ) × 60 min/hr = 1.08
- CFM \text{CFM} CFM = Volume flow rate of air in cubic feet per minute
- Δ T \Delta T Δ T = Temperature difference between entering and leaving air streams (°F)
- Latent Heat Gain Formula
Latent heat transfer changes the moisture content (humidity ratio) of air without altering its dry-bulb temperature. Vaporizing water requires approximately 1,050 to 1,061 Btu per pound of water. The rate of latent heat gain from air exchange is defined as: Q latent = 0.68 × CFM × Δ W grains Q_{\text{latent}} = 0.68 \times \text{CFM} \times \Delta W_{\text{grains}} Q latent = 0.68 × CFM × Δ W grains
Where:
0.68 0.68 0.68 is the latent air factor: density ( 0.075 lb/ft 3 ) × heat of vaporization ( 1 , 061 Btu/lb ) × 60 min/hr / 7 , 000 grains/lb ≈ 0.68 \text{density } (0.075 \text{ lb/ft}^3) \times \text{heat of vaporization } (1,061 \text{ Btu/lb}) \times 60 \text{ min/hr} / 7,000 \text{ grains/lb} \approx 0.68 density ( 0.075 lb/ft 3 ) × heat of vaporization ( 1 , 061 Btu/lb ) × 60 min/hr /7 , 000 grains/lb ≈ 0.68
Δ W grains \Delta W_{\text{grains}} Δ W grains = Difference in humidity ratio between outdoor/entering air and indoor design air (expressed in grains of moisture per pound of dry air; 1 lb = 7 , 000 grains 1 \text{ lb} = 7,000 \text{ grains} 1 lb = 7 , 000 grains )
Total Heat (Enthalpy) Formula
Total cooling load is the arithmetic sum of sensible and latent gains: Q total = Q sensible + Q latent = 4.5 × CFM × Δ h Q_{\text{total}} = Q_{\text{sensible}} + Q_{\text{latent}} = 4.5 \times \text{CFM} \times \Delta h Q total = Q sensible + Q latent = 4.5 × CFM × Δ h
Where Δ h \Delta h Δ h represents the enthalpy difference in Btu per pound of dry air.
- Sensible Heat Gain Components
- 1. Envelope Conduction and Fenestration Solar Gain
Conduction through walls, doors, ceilings, and roofs is calculated using assembly U U U -factors multiplied by net surface areas and adjusted Cooling Load Temperature Differences (CLTD). CLTD values correct for solar radiation absorbed on exterior dark surfaces, roof slope, assembly thermal storage capacity (thermal mass), and daily temperature range.
Fenestration sensible gain combines conductive gain ( U × A × Δ T U \times A \times \Delta T U × A × Δ T ) and radiant solar transmission ( A × SHGC × Peak Solar Irradiance × Internal Shading Coefficient A \times \text{SHGC} \times \text{Peak Solar Irradiance} \times \text{Internal Shading Coefficient} A × SHGC × Peak Solar Irradiance × Internal Shading Coefficient ). In an energy-efficient Arkansas home with Low-E glass (SHGC 0.22), fenestration solar heat gain typically constitutes 25% to 40% of the entire sensible cooling load.
2. Internal Sensible Heat Gains
ACCA Manual J establishes strict empirical allowances for internal sensible loads to prevent oversizing:
Occupants : Sized at 230 Btu/h sensible per person . The design number of occupants is standardized as the number of bedrooms plus one (e.g., a 3-bedroom home is evaluated for 3 + 1 = 4 3 + 1 = 4 3 + 1 = 4 occupants, yielding 4 × 230 = 920 Btu/h 4 \times 230 = 920 \text{ Btu/h} 4 × 230 = 920 Btu/h sensible gain).
Kitchen Appliances : Standard residential baseline allowance is 1,200 Btu/h sensible (assigned exclusively to the kitchen zone), assuming intermittent cooking and normal refrigerator/range operation.
Lighting and Miscellaneous Plug Loads : High-efficiency LED lighting averages 0.5 to 1.0 Btu/h per square foot, while general electronic plug loads (televisions, computers) contribute an additional 800 to 1,500 Btu/h sensible depending on floor area ( 1 Watt = 3.412 Btu/h 1 \text{ Watt} = 3.412 \text{ Btu/h} 1 Watt = 3.412 Btu/h ).
3. Duct Sensible Heat Gains in Unconditioned Attics
Ductwork routing through an unconditioned attic space represents one of the largest sensible cooling penalties in residential construction. On a 96°F afternoon in Little Rock, solar radiation absorbed by dark asphalt roof shingles elevates attic air temperatures to 130°F to 140°F , with roof deck radiant temperatures exceeding 160°F :
Conduction through Duct Insulation : Conditioned supply air moving through the attic at 55°F experiences a temperature differential of Δ T = 135 ∘ F − 55 ∘ F = 80 ∘ F \Delta T = 135^\circ\text{F} - 55^\circ\text{F} = 80^\circ\text{F} Δ T = 13 5 ∘ F − 5 5 ∘ F = 8 0 ∘ F . Even with code-mandated R-8 duct insulation ( U = 1 / 8 = 0.125 U = 1 / 8 = 0.125 U = 1/8 = 0.125 ), a 400 ft² sheet metal or flex duct network incurs: Q duct conduction = 0.125 × 400 × 80 = 4 , 000 Btu/h sensible Q_{\text{duct conduction}} = 0.125 \times 400 \times 80 = 4,000 \text{ Btu/h sensible} Q duct conduction = 0.125 × 400 × 80 = 4 , 000 Btu/h sensible
Duct Leakage Penalty : Air leakage from the return ductwork in an unconditioned attic operates under negative pressure. If return plenums or boots have unsealed joints, the blower fan sucks 135°F attic air directly into the return airstream, raising the temperature of air entering the evaporator coil and instantly destroying 15% to 30% of the cooling system's net capacity.
- Latent Heat Gain Components
- 1. Internal Moisture Generation
Moisture generated inside the home increases the indoor humidity ratio without increasing the temperature:
Occupants : Each occupant releases 200 Btu/h latent heat through normal breathing and insensible perspiration ( 4 occupants × 200 = 800 Btu/h latent 4 \text{ occupants} \times 200 = 800 \text{ Btu/h latent} 4 occupants × 200 = 800 Btu/h latent ). Under moderate activity, this equals approximately 0.19 pounds of water vapor per hour per person.
Household Activities : Unvented cooking, dishwashing, showering, indoor clothes drying, and houseplants introduce an additional 15 to 25 pounds of water vapor into the home daily (equivalent to 15,000 to 25,000 Btu of latent heat distributed across the day).
2. Infiltration and Ventilation Latent Loads
Infiltration occurs when outdoor air leaks into the building envelope through cracks, window frame joints, door jambs, and mechanical penetrations. In Arkansas, summer outdoor air carries massive quantities of suspended water vapor: +-------------------------------------------------------------------------+
- | OUTDOOR VS. INDOOR MOISTURE CONTENT (LITTLE ROCK) |
- +-------------------------------------------------------------------------+
- | OUTDOOR (96°F DB / 76°F WB): |
- | * Absolute Humidity Ratio (W_outdoor): 116.0 grains moisture / lb air |
- | * Dew Point Temperature: 71.0°F |
- +-------------------------------------------------------------------------+
- | INDOOR (75°F DB / 50% RH): |
- | * Absolute Humidity Ratio (W_indoor): 64.6 grains moisture / lb air |
- | * Dew Point Temperature: 55.1°F |
- +-------------------------------------------------------------------------+
- | MOISTURE DEFICIT (Delta W): 51.4 grains / lb dry air |
- +-------------------------------------------------------------------------+
If a residence experiences a modest infiltration rate of 120 CFM of outdoor air in Little Rock: Q latent infiltration = 0.68 × CFM × Δ W = 0.68 × 120 × ( 116.0 − 64.6 ) Q_{\text{latent infiltration}} = 0.68 \times \text{CFM} \times \Delta W = 0.68 \times 120 \times (116.0 - 64.6) Q latent infiltration = 0.68 × CFM × Δ W = 0.68 × 120 × ( 116.0 − 64.6 ) Q latent infiltration = 0.68 × 120 × 51.4 = 4 , 194 Btu/h latent Q_{\text{latent infiltration}} = 0.68 \times 120 \times 51.4 = 4,194 \text{ Btu/h latent} Q latent infiltration = 0.68 × 120 × 51.4 = 4 , 194 Btu/h latent
This infiltration load represents over one-third of a ton of pure moisture removal demand ( 4 , 194 / 12 , 000 = 0.35 tons 4,194 / 12,000 = 0.35 \text{ tons} 4 , 194/12 , 000 = 0.35 tons ) introduced solely through uncontrolled air leakage.
The Sensible Heat Ratio (SHR) and Equipment Dynamics
The Sensible Heat Ratio (SHR) is a fundamental metric that describes the proportion of sensible cooling relative to the total cooling load: SHR = Q sensible Q total = Q sensible Q sensible + Q latent \text{SHR} = \frac{Q_{\text{sensible}}}{Q_{\text{total}}} = \frac{Q_{\text{sensible}}}{Q_{\text{sensible}} + Q_{\text{latent}}} SHR = Q total Q sensible = Q sensible + Q latent Q sensible
In hot, dry climates (such as Phoenix, Arizona), the building SHR is often 0.90 to 0.95 , meaning nearly all cooling demand is sensible temperature reduction.
In Arkansas's humid climate, the building SHR typically ranges between 0.70 and 0.80 . Approximately 20% to 30% of the entire cooling workload must be dedicated to extracting moisture from the air.
The Danger of System Oversizing in Humid Climates
When an HVAC system is oversized (for example, installing a 4-ton unit where Manual J calculated a 2.5-ton peak load):
The oversized system delivers excessive sensible capacity, dropping the indoor room temperature from 77°F to 75°F in a rapid 7-minute burst.
The thermostat satisfies its sensible setpoint and shuts the system down.
Psychrometric Failure : It takes approximately 10 to 12 minutes of continuous compressor run-time for the evaporator coil surface to chill below the indoor dew point (55°F), begin condensing moisture, and start draining water out of the condensate pan.
Because the oversized unit short-cycles in 7-minute intervals, it shuts off before any meaningful latent dehumidification occurs. Water on the coil revaporizes into the airstream as the blower cycles off, driving indoor relative humidity to 65% to 75% . +-------------------------------------------------------------------------+
- | PROPERLY SIZED VS. OVERSIZED COOLING RUNTIME CYCLES |
- +-------------------------------------------------------------------------+
- | PROPERLY SIZED (Long, Steady Cycles: 20-30 Mins): |
- | [Min 0-5: Coil Chills] -> [Min 6-25: Deep Condensation & Moisture Drain]|
- | Result: 75°F DB, 48% RH (Crisp, Healthy, Energy Efficient) |
- +-------------------------------------------------------------------------+
- | OVERSIZED SYSTEM (Short Rapid Cycling: 6-8 Mins): |
- | [Min 0-5: Coil Chills] -> [Min 7: Thermostat Satisfies! Unit SHUTS OFF] |
- | Result: 75°F DB, 68% RH (Clammy, Musty, Microbial Growth Risk) |
- +-------------------------------------------------------------------------+
- Comprehensive Cooling Load Sizing Example: Arkansas Residence
Consider a single-story 2,200 ft² custom residence in Fort Smith, Arkansas (Summer 1% DB = 98°F, Coincident WB = 76°F, Daily Range = Medium, Indoor Design = 75°F DB / 50% RH). The calculated heat gains across all building components are tabulated below:
Heat Gain Source Calculation Method / Engineering Parameters Sensible Gain (Btu/h) Latent Gain (Btu/h)
Opaque Exterior Walls U = 0.065 , A = 1 , 850 ft 2 , CLTD = 17 ∘ F U = 0.065, A = 1,850 \text{ ft}^2, \text{CLTD} = 17^\circ\text{F} U = 0.065 , A = 1 , 850 ft 2 , CLTD = 1 7 ∘ F 2,045 0
Ceiling under Attic U = 0.026 ( R − 38 ) , A = 2 , 200 ft 2 , CLTD = 34 ∘ F U = 0.026 (R-38), A = 2,200 \text{ ft}^2, \text{CLTD} = 34^\circ\text{F} U = 0.026 ( R − 38 ) , A = 2 , 200 ft 2 , CLTD = 3 4 ∘ F 1,945 0
Fenestration Conduction U = 0.28 , A = 320 ft 2 , Δ T = 23 ∘ F U = 0.28, A = 320 \text{ ft}^2, \Delta T = 23^\circ\text{F} U = 0.28 , A = 320 ft 2 , Δ T = 2 3 ∘ F 2,060 0
Fenestration Solar Gain SHGC = 0.22 , A = 320 ft 2 , Peak Solar Irradiance \text{SHGC} = 0.22, A = 320 \text{ ft}^2, \text{Peak Solar Irradiance} SHGC = 0.22 , A = 320 ft 2 , Peak Solar Irradiance 6,850 0
Slab Floor Perimeter Edge conduction at peak ambient 480 0
Internal: Occupants 3 Bedrooms ( 3 + 1 = 4 people 3 + 1 = 4 \text{ people} 3 + 1 = 4 people ); 230 Sens. / 200 Lat. 230 \text{ Sens.} / 200 \text{ Lat.} 230 Sens. /200 Lat. 920 800
Internal: Kitchen & Plugs Standard kitchen (1,200) + appliances & lighting (2,400) 3,600 600
Infiltration Air (110 CFM) Q s = 1.08 × 110 × 23 ; Q L = 0.68 × 110 × 51.4 Q_s = 1.08 \times 110 \times 23; Q_L = 0.68 \times 110 \times 51.4 Q s = 1.08 × 110 × 23 ; Q L = 0.68 × 110 × 51.4 2,732 3,845
- Attic Duct System (R-8) Conduction (3,600 Btu/h) + 5% return leakage (1,850 Btu/h) 4,250 1,200
- SUBTOTALS 24,882 Btu/h 6,445 Btu/h
Load Aggregation & Sensible Heat Ratio Q total = Q sensible + Q latent = 24 , 882 + 6 , 445 = 31 , 327 Btu/h Q_{\text{total}} = Q_{\text{sensible}} + Q_{\text{latent}} = 24,882 + 6,445 = 31,327 \text{ Btu/h} Q total = Q sensible + Q latent = 24 , 882 + 6 , 445 = 31 , 327 Btu/h Required Tonnage = 31 , 327 Btu/h 12 , 000 Btu/(hr ⋅ ton) = 2.61 tons \text{Required Tonnage} = \frac{31,327 \text{ Btu/h}}{12,000 \text{ Btu/(hr} \cdot \text{ton)}} = 2.61 \text{ tons} Required Tonnage = 12 , 000 Btu/(hr ⋅ ton) 31 , 327 Btu/h = 2.61 tons Building SHR = 24 , 882 31 , 327 = 0.794 \text{Building SHR} = \frac{24,882}{31,327} = 0.794 Building SHR = 31 , 327 24 , 882 = 0.794
To satisfy this structure, the HVAC contractor cannot simply select a 3-ton nominal unit rated at nominal conditions. The selected machinery must deliver at least 24,882 Btu/h of net sensible capacity and at least 6,445 Btu/h of net latent capacity under Fort Smith's 98°F ambient and 75°F/63°F entering coil conditions.