Study guide

3.3 Heating Load Calculations & Infiltration Rates

Arkansas HVAC/R Contractor License Exam

Track your progress as you read

Finished sections get a check mark.

1 Arkansas HVAC/R Licensing Law, Board Rules & Administration

1.1 Arkansas HVAC/R Board Authority, Statutes & Definitions 1.2 License Classifications & Capacity Limitations 1.3 Registrant Requirements, Apprenticeship & Experience Verification 1.4 License Renewal, Continuing Education & Disciplinary Actions

2 HVAC Thermodynamics, Psychrometrics & Gas Laws

2.1 Principles of Heat Transfer & Thermodynamic Fundamentals 2.2 Psychrometric Chart Dynamics & Air Properties 2.3 Psychrometric Processes & Air Mixture Calculations 2.4 Gas Laws Applied to HVAC/R Systems

3 Heating and Cooling Load Calculations (Manual J & S)

3.1 ACCA Manual J Design Conditions & Thermal Envelopes 3.2 Peak Cooling Load Calculations: Sensible vs. Latent Heat Gain 3.3 Heating Load Calculations & Infiltration Rates 3.4 ACCA Manual S Equipment Selection & Verification

4 Ductwork Design, Sizing & SMACNA Standards (Manual D)

4.1 ACCA Manual D Airflow Fundamentals & External Static Pressure 4.2 Equal Friction & Static Regain Duct Sizing Methods 4.3 Duct Fittings, Equivalent Length & Dynamic Losses 4.4 SMACNA Duct Construction Standards & Joint Sealing

5 Air Distribution, Balancing & Ventilation Codes

5.1 Supply & Return Air Distribution Hardware (Grilles, Registers, Diffusers) 5.2 System Airflow Testing, Adjusting & Balancing (TAB) 5.3 Ventilation Standards: ASHRAE 62.1, 62.2 & 2021 IMC Ventilation Air

6 Mechanical Refrigeration Cycle & Components

6.1 The Vapor-Compression Refrigeration Cycle 6.2 Compressors & Operating Characteristics 6.3 Condensers & Evaporators 6.4 Metering Devices & Refrigerant Flow Controls 6.5 Refrigerant Line Sizing, Oil Return & Field Piping Practices

7 Refrigerants, Oils & EPA Section 608 Regulations

7.1 Refrigerant Chemistry, ASHRAE Standard 34 & A2L Transition 7.2 Lubricating Oils & System Compatibility 7.3 EPA Section 608 Regulatory Mandates & Recovery Standards 7.4 System Evacuation, Dehydration & Leak Detection

8 Air Conditioning & Heat Pump Systems

8.1 Residential & Commercial Split Systems and Package RTUs 8.2 Air-Source Heat Pumps & The Reversing Valve 8.3 Supplemental & Emergency Heating Systems 8.4 Dual-Fuel & Geothermal (Ground-Source) Heat Pump Systems

9 Gas Furnaces, Combustion Air & Venting (IFGC / IMC)

9.1 Gas Furnace Types, AFUE Ratings & Sequence of Operation 9.2 Gas Burners, Ignition Systems & Flame Safeguard Controls 9.3 Combustion Air Requirements (IFGC Chapter 3 / IMC Chapter 7) 9.4 Flue Gas Venting & Category I-IV Venting Systems

10 Boilers, Hydronics & Fuel Gas Piping

10.1 Hydronic Heating Systems, Low-Pressure Boilers & ASME Code 10.2 Hydronic Distribution, Circulator Pumps & Piping Loops 10.3 Fuel Gas Piping Materials, Sizing & Pressure Testing (IFGC Chapter 4) 10.4 Gas Regulators, Manifold Pressure & Gas Meter Sizing 10.5 Condensate Disposal, Piping Support & Mechanical Insulation

11 Electrical Fundamentals, Motors & Control Circuits

11.1 HVAC Electrical Fundamentals, Ohm's Law & Power Calculations 11.2 Single-Phase & Three-Phase Electric Motors in HVAC 11.3 Low-Voltage Control Circuits & Thermostats

12 National Electrical Code (NEC) for HVAC Equipment

12.1 NEC Article 440: Hermetic Refrigerant Motor-Compressors & Branch Circuits 12.2 Equipment Disconnecting Means & Overcurrent Protective Devices (OCPD) 12.3 Motor Branch Circuit Sizing & Conductor Ampacity (NEC Article 430 & Tables)

13 System Maintenance, Troubleshooting & Safety Standards

13.1 Systematic Mechanical & Electrical Troubleshooting 13.2 Airflow & Refrigerant Charge Diagnostics 13.3 Jobsite Safety, OSHA Standards & Personal Protective Equipment

14 Plan Reading, Estimating & HVAC/R Trade Math

14.1 Mechanical Plan Symbols, Schedules & Abbreviations 14.2 Architectural Scales, Dimensions & Quantity Takeoff 14.3 Material, Labor & Bid Estimating 14.4 Applied HVAC/R Trade Math & Unit Conversions

3.3 Heating Load Calculations & Infiltration Rates

Key Takeaways Explain This Topic AI

ACCA Manual J heating load calculations operate under strict steady-state nighttime baselines that forbid crediting internal heat gains (occupants, lights, appliances) or daytime solar radiation.

The heating design temperature difference (Delta T) is calculated as indoor design temperature (70°F) minus the 99% outdoor winter dry-bulb, generating baselines of 48°F in Little Rock, 50°F in Fort Smith, and 56°F in Fayetteville.

Slab-on-grade heat loss occurs predominantly at the foundation perimeter and is calculated using linear F-factors (Q = F * P * Delta T) rather than surface area U-factors.

Infiltration sensible heat loss is quantified using Q_sensible = 1.08 * CFM * Delta T, where CFM is evaluated via the Air Change per Hour (ACH) method or converted from blower door depressurization testing (ACH50 / N-factor).

Supply and return duct leakage in unconditioned attics or vented crawlspaces dramatically magnifies heating loads by losing heated air and drawing freezing ambient air into the return stream.

Last updated: September 2026

3.3 Heating Load Calculations & Infiltration Rates

Note

Steady-State Design Philosophy : Unlike cooling calculations—which account for dynamic diurnal solar movement, thermal decrement delay, and internal heat loads—ACCA Manual J heating calculations are strictly steady-state . Under standard engineering protocol, heating loads are evaluated under worst-case winter conditions occurring during pre-dawn hours when outdoor temperatures reach their 99% design minimum, wind speeds peak, and solar irradiation is zero.

Designing residential heating systems under the Arkansas Mechanical Code requires rigorous adherence to ACCA Manual J. Overestimating heating loads leads to oversized gas furnaces that short-cycle, causing severe heat exchanger thermal stress, wide room temperature swings, and noisy airflow. Conversely, undersizing results in heat pumps failing to maintain 70°F comfort thresholds, relying excessively on expensive electric resistance auxiliary heat.

Mandatory Exclusions: The Zero-Credit Safety Baseline

A critical rule tested on the Arkansas HVAC/R Contractor licensing examination is the prohibition of non-continuous thermal credits in peak heating calculations:

Zero Solar Radiation Credit : No credit is permitted for passive solar heat gain through windows, skylights, or sunlit walls. Peak heating design conditions frequently occur on overcast winter days or during sub-freezing nights when solar irradiance is nonexistent.

Zero Internal Heat Credit : Heat generated by occupants (230 Btu/h sensible each), lighting, televisions, cooking appliances, and computers must be excluded from the heating load calculation. Occupants may be asleep or away from home, and appliances remain idle for extended intervals. Sizing heating equipment to rely on internal gains creates an unsafe condition during sub-freezing cold snaps.

Indoor Setpoint Standardization : The indoor design temperature for heating calculations is standardized at exactly 70°F dry-bulb across all rooms and zones.

Outdoor Design Temperatures & Regional Heating Δ T \Delta T Δ T in Arkansas

Under ACCA Manual J Table 1A, the 99% winter outdoor design dry-bulb temperature represents the baseline condition that is equaled or exceeded for 99% of all winter hours. The heating design temperature difference ( Δ T \Delta T Δ T ) is calculated as: Δ T heating = T indoor setpoint − T outdoor 99% DB = 70 ∘ F − T outdoor 99% DB \Delta T_{\text{heating}} = T_{\text{indoor setpoint}} - T_{\text{outdoor 99\% DB}} = 70^\circ\text{F} - T_{\text{outdoor 99\% DB}} Δ T heating ​ = T indoor setpoint ​ − T outdoor 99% DB ​ = 7 0 ∘ F − T outdoor 99% DB ​ +-------------------------------------------------------------------------+

  • | REGIONAL HEATING DESIGN DELTA-T ACROSS ARKANSAS |
  • +-------------------------------------------------------------------------+
  • | Fayetteville / Bentonville (Zone 4A): |
  • | * Outdoor 99% Winter Design: 14°F |
  • | * Design Delta-T: 70°F - 14°F = 56°F (Highest Heating Demand in AR) |
  • +-------------------------------------------------------------------------+
  • | Fort Smith / River Valley (Zone 3A): |
  • | * Outdoor 99% Winter Design: 20°F |
  • | * Design Delta-T: 70°F - 20°F = 50°F |
  • +-------------------------------------------------------------------------+
  • | Little Rock / Central Arkansas (Zone 3A): |
  • | * Outdoor 99% Winter Design: 22°F |
  • | * Design Delta-T: 70°F - 22°F = 48°F |
  • +-------------------------------------------------------------------------+
  • | Texarkana / South Arkansas (Zone 3A): |
  • | * Outdoor 99% Winter Design: 25°F |
  • | * Design Delta-T: 70°F - 25°F = 45°F |
  • +-------------------------------------------------------------------------+

Notice that a home constructed in Fayetteville experiences an 16.7% higher thermal driving potential ( Δ T = 56 ∘ F \Delta T = 56^\circ\text{F} Δ T = 5 6 ∘ F ) than an identical structure built in Little Rock ( Δ T = 48 ∘ F \Delta T = 48^\circ\text{F} Δ T = 4 8 ∘ F ).

Envelope Transmission Losses: Opaque Assemblies and Slab Floors

Conduction heat loss across opaque building envelope assemblies follows Fourier's steady-state relationship: Q = U × A × Δ T Q = U \times A \times \Delta T Q = U × A × Δ T

Where:

  • Q Q Q = Steady-state heat loss rate (Btu/h)
  • U U U = Overall coefficient of heat transmission ( 1 / R total 1 / R_{\text{total}} 1/ R total ​ )
  • A A A = Net surface area of the assembly (ft²)

Δ T \Delta T Δ T = Heating design temperature difference ( 70 ∘ F − T outdoor 70^\circ\text{F} - T_{\text{outdoor}} 7 0 ∘ F − T outdoor ​ )

Above-Grade Walls and Ceilings

Ceiling / Attic Assemblies : Under the Arkansas Energy Code, ceilings with unconditioned attics mandate a minimum thermal resistance of R-38 (Climate Zone 3A) or R-49 (Climate Zone 4A). For an R-38 ceiling in Little Rock ( Δ T = 48 ∘ F \Delta T = 48^\circ\text{F} Δ T = 4 8 ∘ F ), the conductive loss per square foot is: q = 1 38 × 48 = 1.263 Btu/(h ⋅ ft 2 ) q = \frac{1}{38} \times 48 = 1.263 \text{ Btu/(h} \cdot \text{ft}^2) q = 38 1 ​ × 48 = 1.263 Btu/(h ⋅ ft 2 )

Truss Heel Compression : Near exterior eaves, roof slope restricts insulation depth. If blown fiberglass is compressed to 4 inches over exterior wall top plates, its local resistance drops to R-11 to R-13. Manual J calculations must incorporate weighted average U U U -factors to account for truss heel thermal bridging unless raised-heel (energy) trusses are installed.

Slab-on-Grade Foundation Heat Loss

Slab-on-grade floors do not lose heat uniformly across their surface. The ground directly beneath the center of a slab maintains a relatively stable, warm temperature (~55°F to 60°F). Consequently, over 80% of all slab heat loss occurs around the exposed exterior perimeter edge , where heat conducts horizontally through the concrete foundation stem into the sub-freezing outdoor air and freezing upper soil layers. OUTDOOR COLD AIR (14°F - 22°F)

  • |
  • v
  • +------------------------+-------------------+
  • | Concrete Slab Floor | (Interior 70°F) |
  • | +-------------------+
  • | <--- Heat Conduction Path |
  • | |
  • | [Exposed Slab Edge] |
  • | (Perimeter F-Factor) |
  • +------------------------+ |
  • | Stem Wall / Footing | Warm Earth |
  • | | (55°F - 60°F) |
  • +------------------------+-------------------+

Because slab heat loss is a edge phenomenon rather than a surface area phenomenon, ACCA Manual J abandons the standard U × A × Δ T U \times A \times \Delta T U × A × Δ T formula in favor of the Perimeter F F F -Factor Equation : Q slab = F × P × Δ T Q_{\text{slab}} = F \times P \times \Delta T Q slab ​ = F × P × Δ T

Where:

  • Q slab Q_{\text{slab}} Q slab ​ = Perimeter heat loss rate (Btu/h)
  • F F F = Slab perimeter heat loss coefficient (expressed in Btu/(h · ft of perimeter · °F Δ T \Delta T Δ T ))
  • P P P = Linear feet of exposed exterior slab perimeter (ft)

Δ T \Delta T Δ T = Outdoor-to-indoor heating temperature difference ( 70 ∘ F − T outdoor 70^\circ\text{F} - T_{\text{outdoor}} 7 0 ∘ F − T outdoor ​ )

Slab Insulation Configuration F-Factor (Btu/(h · ft · °F)) 180 Linear Foot Perimeter Loss in Little Rock (48°F Δ T \Delta T Δ T )

Uninsulated Slab (Common older construction) 0.73 0.73 × 180 × 48 = 6 , 307 Btu/h 0.73 \times 180 \times 48 = \mathbf{6,307 \text{ Btu/h}} 0.73 × 180 × 48 = 6 , 307 Btu/h

R-5 Perimeter Edge Insulation (12" depth) 0.58 0.58 × 180 × 48 = 5 , 011 Btu/h 0.58 \times 180 \times 48 = \mathbf{5,011 \text{ Btu/h}} 0.58 × 180 × 48 = 5 , 011 Btu/h

R-10 Perimeter Edge Insulation (24" depth / IECC) 0.42 0.42 × 180 × 48 = 3 , 629 Btu/h 0.42 \times 180 \times 48 = \mathbf{3,629 \text{ Btu/h}} 0.42 × 180 × 48 = 3 , 629 Btu/h

Fully Insulated Slab & Underslab R-10 0.36 0.36 × 180 × 48 = 3 , 110 Btu/h 0.36 \times 180 \times 48 = \mathbf{3,110 \text{ Btu/h}} 0.36 × 180 × 48 = 3 , 110 Btu/h

Installing R-10 perimeter edge insulation reduces slab transmission loss by over 42% , directly shrinking the required heating equipment capacity.

Infiltration and Ventilation Rates: Air Exchange vs. Crack Methods

Infiltration is the uncontrolled leakage of sub-freezing outdoor air into the conditioned space driven by wind pressure, indoor-outdoor air density differentials (stack effect), and HVAC duct imbalances. Cold infiltration air entering the structure must be heated from outdoor design temperature to 70°F indoor design temperature.

The Sensible Heat Air Formula

The sensible load imposed by heating infiltrating outdoor air is governed by: Q infiltration = 1.08 × CFM × Δ T Q_{\text{infiltration}} = 1.08 \times \text{CFM} \times \Delta T Q infiltration ​ = 1.08 × CFM × Δ T

  • Infiltration Quantification Methods
  • 1. Air Change per Hour (ACH) Method

The ACH method estimates air exchange based on structural airtightness categories and total conditioned volume: CFM inf = Volume (ft 3 ) × ACH natural 60 \text{CFM}_{\text{inf}} = \frac{\text{Volume (ft}^3) \times \text{ACH}_{\text{natural}}}{60} CFM inf ​ = 60 Volume (ft 3 ) × ACH natural ​ ​

Tight Construction (0.15 - 0.25 ACH) : Modern homes built to the Arkansas Energy Code with continuous air barriers, sealed penetrations, gasketed electrical boxes, and taped exterior sheathing.

Semi-Tight / Average Construction (0.35 - 0.45 ACH) : Standard 1990s-2010s construction with caulked joints and weatherstripped doors.

Loose Construction (0.60 - 1.0+ ACH) : Older pre-1980s homes with unsealed framing, drafty single-pane windows, and uncaulked baseboards.

2. The Crack Length Method

The crack method evaluates the physical perimeter (linear feet of crack) around window sashes, door jambs, and wall-sole plate junctions, multiplying crack length by empirical infiltration rates based on wind velocity (typically 15 mph in winter). While historically utilized for manual tabular calculations, modern Manual J software employs detailed leakage area correlations.

3. Blower Door Depressurization Testing ( A C H 50 ACH_{50} A C H 50 ​ )

The Arkansas Energy Code mandates that new residential construction undergo building envelope tightness verification via a calibrated blower door depressurization test performed at 50 Pascals (Pa) of pressure differential:

Modern code requires an airtightness benchmark of ≤ 3.0 \le 3.0 ≤ 3.0 to 5.0 ACH 50 5.0 \text{ ACH}_{50} 5.0 ACH 50 ​ (Climate Zones 3A and 4A).

To convert blower door test results ( ACH 50 \text{ACH}_{50} ACH 50 ​ ) into the natural air change rate ( ACH natural \text{ACH}_{\text{natural}} ACH natural ​ ) required for Manual J design load calculations, engineers apply the Lawrence Berkeley Laboratory (LBL) Infiltration Factor ( N N N -factor) : ACH natural = ACH 50 N \text{ACH}_{\text{natural}} = \frac{\text{ACH}_{50}}{N} ACH natural ​ = N ACH 50 ​ ​

For Arkansas's climatic zone, 1-to-2 story residential structures typically have an N N N -factor between 16 and 20 (depending on wind shielding and building height). If a blower door test in Fort Smith measures 4.0 ACH 50 4.0 \text{ ACH}_{50} 4.0 ACH 50 ​ with an N N N -factor of 18: ACH natural = 4.0 18 = 0.222 ACH \text{ACH}_{\text{natural}} = \frac{4.0}{18} = 0.222 \text{ ACH} ACH natural ​ = 18 4.0 ​ = 0.222 ACH

For an 18,000 ft³ home (2,250 ft² with 8-foot ceilings): CFM inf = 18 , 000 × 0.222 60 = 66.6 CFM \text{CFM}_{\text{inf}} = \frac{18,000 \times 0.222}{60} = 66.6 \text{ CFM} CFM inf ​ = 60 18 , 000 × 0.222 ​ = 66.6 CFM Q infiltration = 1.08 × 66.6 × ( 70 ∘ F − 20 ∘ F ) = 1.08 × 66.6 × 50 = 3 , 596 Btu/h Q_{\text{infiltration}} = 1.08 \times 66.6 \times (70^\circ\text{F} - 20^\circ\text{F}) = 1.08 \times 66.6 \times 50 = \mathbf{3,596 \text{ Btu/h}} Q infiltration ​ = 1.08 × 66.6 × ( 7 0 ∘ F − 2 0 ∘ F ) = 1.08 × 66.6 × 50 = 3 , 596 Btu/h

Duct Conduction and Leakage Heat Losses

Ductwork placed outside the conditioned building envelope—in unconditioned attics, unheated basements, or vented crawlspaces—incurs massive thermal losses that must be added directly to the equipment heating load. +-------------------------------------------------------------------------+

  • | DUCT THERMAL PENALTIES IN UNCONDITIONED SPACES |
  • +-------------------------------------------------------------------------+
  • | 1. SUPPLY CONDUCTION LOSS: |
  • | Supply air at 105°F - 130°F passes through a 20°F attic. |
  • | Extreme Delta-T (85°F - 110°F) causes continuous conductive heat loss|
  • | across R-6 or R-8 duct walls before air reaches the register boots. |
  • +-------------------------------------------------------------------------+
  • | 2. SUPPLY LEAKAGE PENALTY (Exfiltration): |
  • | Supply air escaping through unsealed joints directly enters the cold |
  • | attic. This creates a negative pressure inside the living space, |
  • | forcing an identical volume of freezing outdoor air to infiltrate! |
  • +-------------------------------------------------------------------------+
  • | 3. RETURN LEAKAGE PENALTY (Direct Cold Ingestion): |
  • | Negative pressure inside the return plenum sucks sub-freezing attic |
  • | or crawlspace air directly into the furnace or heat pump air stream, |
  • | slashing supply discharge air temperatures. |
  • +-------------------------------------------------------------------------+

Conduction Loss Equation for Ducts Q duct cond = U duct × A duct surface × ( T supply air − T ambient buffer ) Q_{\text{duct cond}} = U_{\text{duct}} \times A_{\text{duct surface}} \times (T_{\text{supply air}} - T_{\text{ambient buffer}}) Q duct cond ​ = U duct ​ × A duct surface ​ × ( T supply air ​ − T ambient buffer ​ )

If a gas furnace delivers 120°F air through 350 ft² of R-8 ductwork ( U = 0.125 U = 0.125 U = 0.125 ) in an unconditioned Fayetteville attic during 14°F design conditions: Q duct cond = 0.125 × 350 × ( 120 − 14 ) = 0.125 × 350 × 106 = 4 , 638 Btu/h Q_{\text{duct cond}} = 0.125 \times 350 \times (120 - 14) = 0.125 \times 350 \times 106 = \mathbf{4,638 \text{ Btu/h}} Q duct cond ​ = 0.125 × 350 × ( 120 − 14 ) = 0.125 × 350 × 106 = 4 , 638 Btu/h

Uninsulated or poorly sealed duct systems routinely inflate residential heating loads by 20% to 40% . The Arkansas Mechanical Code strictly enforces duct sealing using UL 181-listed mastic and requires all supply and return ducts in unconditioned attics to maintain a minimum insulation value of R-8 .

Loading diagram... Winter Heating Load Pathways and Thermal Losses