Study guide

3.4 ACCA Manual S Equipment Selection & Verification

Arkansas HVAC/R Contractor License Exam

Track your progress as you read

Finished sections get a check mark.

1 Arkansas HVAC/R Licensing Law, Board Rules & Administration

1.1 Arkansas HVAC/R Board Authority, Statutes & Definitions 1.2 License Classifications & Capacity Limitations 1.3 Registrant Requirements, Apprenticeship & Experience Verification 1.4 License Renewal, Continuing Education & Disciplinary Actions

2 HVAC Thermodynamics, Psychrometrics & Gas Laws

2.1 Principles of Heat Transfer & Thermodynamic Fundamentals 2.2 Psychrometric Chart Dynamics & Air Properties 2.3 Psychrometric Processes & Air Mixture Calculations 2.4 Gas Laws Applied to HVAC/R Systems

3 Heating and Cooling Load Calculations (Manual J & S)

3.1 ACCA Manual J Design Conditions & Thermal Envelopes 3.2 Peak Cooling Load Calculations: Sensible vs. Latent Heat Gain 3.3 Heating Load Calculations & Infiltration Rates 3.4 ACCA Manual S Equipment Selection & Verification

4 Ductwork Design, Sizing & SMACNA Standards (Manual D)

4.1 ACCA Manual D Airflow Fundamentals & External Static Pressure 4.2 Equal Friction & Static Regain Duct Sizing Methods 4.3 Duct Fittings, Equivalent Length & Dynamic Losses 4.4 SMACNA Duct Construction Standards & Joint Sealing

5 Air Distribution, Balancing & Ventilation Codes

5.1 Supply & Return Air Distribution Hardware (Grilles, Registers, Diffusers) 5.2 System Airflow Testing, Adjusting & Balancing (TAB) 5.3 Ventilation Standards: ASHRAE 62.1, 62.2 & 2021 IMC Ventilation Air

6 Mechanical Refrigeration Cycle & Components

6.1 The Vapor-Compression Refrigeration Cycle 6.2 Compressors & Operating Characteristics 6.3 Condensers & Evaporators 6.4 Metering Devices & Refrigerant Flow Controls 6.5 Refrigerant Line Sizing, Oil Return & Field Piping Practices

7 Refrigerants, Oils & EPA Section 608 Regulations

7.1 Refrigerant Chemistry, ASHRAE Standard 34 & A2L Transition 7.2 Lubricating Oils & System Compatibility 7.3 EPA Section 608 Regulatory Mandates & Recovery Standards 7.4 System Evacuation, Dehydration & Leak Detection

8 Air Conditioning & Heat Pump Systems

8.1 Residential & Commercial Split Systems and Package RTUs 8.2 Air-Source Heat Pumps & The Reversing Valve 8.3 Supplemental & Emergency Heating Systems 8.4 Dual-Fuel & Geothermal (Ground-Source) Heat Pump Systems

9 Gas Furnaces, Combustion Air & Venting (IFGC / IMC)

9.1 Gas Furnace Types, AFUE Ratings & Sequence of Operation 9.2 Gas Burners, Ignition Systems & Flame Safeguard Controls 9.3 Combustion Air Requirements (IFGC Chapter 3 / IMC Chapter 7) 9.4 Flue Gas Venting & Category I-IV Venting Systems

10 Boilers, Hydronics & Fuel Gas Piping

10.1 Hydronic Heating Systems, Low-Pressure Boilers & ASME Code 10.2 Hydronic Distribution, Circulator Pumps & Piping Loops 10.3 Fuel Gas Piping Materials, Sizing & Pressure Testing (IFGC Chapter 4) 10.4 Gas Regulators, Manifold Pressure & Gas Meter Sizing 10.5 Condensate Disposal, Piping Support & Mechanical Insulation

11 Electrical Fundamentals, Motors & Control Circuits

11.1 HVAC Electrical Fundamentals, Ohm's Law & Power Calculations 11.2 Single-Phase & Three-Phase Electric Motors in HVAC 11.3 Low-Voltage Control Circuits & Thermostats

12 National Electrical Code (NEC) for HVAC Equipment

12.1 NEC Article 440: Hermetic Refrigerant Motor-Compressors & Branch Circuits 12.2 Equipment Disconnecting Means & Overcurrent Protective Devices (OCPD) 12.3 Motor Branch Circuit Sizing & Conductor Ampacity (NEC Article 430 & Tables)

13 System Maintenance, Troubleshooting & Safety Standards

13.1 Systematic Mechanical & Electrical Troubleshooting 13.2 Airflow & Refrigerant Charge Diagnostics 13.3 Jobsite Safety, OSHA Standards & Personal Protective Equipment

14 Plan Reading, Estimating & HVAC/R Trade Math

14.1 Mechanical Plan Symbols, Schedules & Abbreviations 14.2 Architectural Scales, Dimensions & Quantity Takeoff 14.3 Material, Labor & Bid Estimating 14.4 Applied HVAC/R Trade Math & Unit Conversions

3.4 ACCA Manual S Equipment Selection & Verification

Key Takeaways Explain This Topic AI

ACCA Manual S mandates selecting HVAC equipment using manufacturer expanded performance tables evaluated at local outdoor design temperatures and indoor entering wet-bulb/dry-bulb conditions, strictly prohibiting selection based on nominal AHRI catalog ratings.

Under Manual S cooling sizing limits, single-stage air conditioners must satisfy total cooling load within 90% to 115% (up to 120% for heat pumps where heating load governs), while multi-stage and variable-speed systems can size up to 120% or 130%.

Both sensible and latent capacities must be verified independently: net sensible capacity must equal or exceed the building sensible load, and net latent capacity must equal or exceed the building latent load.

In air-source heat pump applications across Arkansas (Climate Zones 3A/4A), the thermal balance point (typically 28°F to 35°F) defines the temperature where heat pump capacity equals building heat loss, below which supplemental heat stages must engage.

Manual S restricts fossil-fuel furnace output heating capacity to between 100% and 140% of the calculated Manual J heating load, protecting heat exchangers from severe thermal fatigue and eliminating rapid short-cycling.

Last updated: September 2026

3.4 ACCA Manual S Equipment Selection & Verification

Important

The Nominal Rating Fallacy : HVAC equipment must never be selected based on its nominal AHRI (Air-Conditioning, Heating, and Refrigeration Institute) nameplate rating. AHRI standard test conditions evaluate cooling machinery at 95°F outdoor ambient and an unrealistically warm indoor entering condition of 80°F dry-bulb / 67°F wet-bulb. Under actual Arkansas indoor design conditions (75°F dry-bulb / 62.5°F wet-bulb), the true cooling capacity of a "3-ton" (36,000 Btu/h) unit collapses to approximately 30,000 - 32,000 Btu/h. ACCA Manual S requires contractors to look up manufacturer expanded performance data to verify performance under real-world design parameters.

Selecting heating and cooling machinery under the Arkansas Mechanical Code requires following the exact verification protocols established in ACCA Manual S (Residential Equipment Selection). Sizing equipment is not a matter of matching a single tonnage number; it is an engineering verification process that matches net sensible, net latent, and gross heating outputs against the peak loads calculated in ACCA Manual J.

ACCA Manual S Sizing Limits

To prevent the chronic operational failures of oversizing and undersizing, ACCA Manual S defines strict percentage boundaries governing equipment selection relative to the calculated Manual J load: +-------------------------------------------------------------------------+

  • | ACCA MANUAL S COOLING SIZING BOUNDARIES |
  • +-------------------------------------------------------------------------+
  • | SINGLE-STAGE AIR CONDITIONERS: |
  • | * Lower Limit: 90% of Total Cooling Load |
  • | * Upper Limit: 115% of Total Cooling Load |
  • +-------------------------------------------------------------------------+
  • | SINGLE-STAGE HEAT PUMPS: |
  • | * Lower Limit: 90% of Total Cooling Load |
  • | * Upper Limit: 115% (Allowed up to 120% if required for heating) |
  • +-------------------------------------------------------------------------+
  • | MULTI-STAGE / TWO-STAGE COMPRESSORS: |
  • | * Lower Limit: 90% of Total Cooling Load |
  • | * Upper Limit: 120% of Total Cooling Load |
  • +-------------------------------------------------------------------------+
  • | VARIABLE-SPEED / INVERTER COMPRESSORS: |
  • | * Lower Limit: 90% of Total Cooling Load |
  • | * Upper Limit: 120% (Allowed up to 130% if low turndown <= 40%) |
  • +-------------------------------------------------------------------------+
  • | GAS / OIL FURNACES (FOSSIL FUEL): |
  • | * Lower Limit: 100% of Total Heating Load |
  • | * Upper Limit: 140% of Total Heating Load |
  • | * Exception: Up to 200% permitted ONLY if smallest available model |
  • | in product line exceeds 140% |
  • +-------------------------------------------------------------------------+
  • Equipment Selection & Capacity Verification Protocol

ACCA Manual S outlines a sequential, five-step verification protocol that every Arkansas HVAC contractor must document:

Step 1: Establish Local Design Conditions and Target Loads

Extract the target requirements from the ACCA Manual J calculation:

Total Cooling Load ( Q total Q_{\text{total}} Q total ​ ), Sensible Cooling Load ( Q sensible Q_{\text{sensible}} Q sensible ​ ), and Latent Cooling Load ( Q latent Q_{\text{latent}} Q latent ​ )

  • Total Design Heating Load ( Q heating Q_{\text{heating}} Q heating ​ )
  • Local Outdoor Design Temperatures: Summer 1% DB (e.g., 96°F in Little Rock) and Winter 99% DB (22°F)
  • Indoor Design Conditions: 75°F DB and 63°F entering wet-bulb (EWB)
  • Step 2: Tentative Model Selection & Airflow Specification

Select a tentative condenser-evaporator coil combination from the manufacturer's product catalog. Specify the target evaporator airflow rate in CFM (standard residential airflow ranges between 350 and 450 CFM per ton , with 350 to 375 CFM/ton preferred in humid Arkansas climates to depress coil temperature and maximize latent moisture removal).

Step 3: Interpolate Manufacturer Expanded Performance Tables

Locate the manufacturer's expanded performance data matrix for the exact outdoor condensing unit and matched indoor coil combination. Look up the performance numbers at the actual operating intersection:

  • Outdoor Ambient Temperature : 96°F DB
  • Entering Indoor Coil Air Conditions : 75°F dry-bulb / 63°F wet-bulb
  • Selected Airflow : e.g., 1,100 CFM

Record the Gross Total Cooling Capacity ( T C gross TC_{\text{gross}} T C gross ​ ) and Gross Sensible Cooling Capacity ( S C gross SC_{\text{gross}} S C gross ​ ).

Step 4: Calculate Net Capacities (Blower Heat Adjustment)

If the indoor air handler or furnace features an internal blower motor located downstream of the coil or within the conditioned airstream, the electrical energy consumed by the motor dissipates into the supply air as heat ( 1 Watt = 3.412 Btu/h 1 \text{ Watt} = 3.412 \text{ Btu/h} 1 Watt = 3.412 Btu/h ):

Standard blower motors add approximately 1,000 to 2,000 Btu/h of sensible heat to the supply airstream.

Net Sensible Capacity : S C net = S C gross − Q blower heat SC_{\text{net}} = SC_{\text{gross}} - Q_{\text{blower heat}} S C net ​ = S C gross ​ − Q blower heat ​

Net Total Capacity : T C net = T C gross − Q blower heat TC_{\text{net}} = TC_{\text{gross}} - Q_{\text{blower heat}} T C net ​ = T C gross ​ − Q blower heat ​

Net Latent Capacity : L C net = T C net − S C net = T C gross − S C gross LC_{\text{net}} = TC_{\text{net}} - SC_{\text{net}} = TC_{\text{gross}} - SC_{\text{gross}} L C net ​ = T C net ​ − S C net ​ = T C gross ​ − S C gross ​ (blower heat affects sensible capacity only; latent moisture extraction remains unaffected).

Step 5: Validate Against Manual S Acceptance Criteria

The selected equipment is verified as compliant if and only if it satisfies all three criteria simultaneously: 0.90 × Q total ≤ T C net ≤ 1.15 × Q total 0.90 \times Q_{\text{total}} \le TC_{\text{net}} \le 1.15 \times Q_{\text{total}} 0.90 × Q total ​ ≤ T C net ​ ≤ 1.15 × Q total ​ S C net ≥ Q sensible SC_{\text{net}} \ge Q_{\text{sensible}} S C net ​ ≥ Q sensible ​ L C net ≥ Q latent LC_{\text{net}} \ge Q_{\text{latent}} L C net ​ ≥ Q latent ​

If S C net SC_{\text{net}} S C net ​ falls below the calculated sensible load, the contractor must increase the design airflow (e.g., from 350 to 400 CFM/ton) or reselect equipment. If L C net LC_{\text{net}} L C net ​ is deficient, reducing airflow down to 350 CFM/ton drops the coil temperature, converting sensible capacity into latent dehumidification capacity.

Heat Pump Sizing Dynamics & Balance Point Analysis

Sizing air-source heat pumps in Arkansas presents a unique engineering challenge due to the divergent thermodynamic curves of building heat loss versus heat pump heating capacity. Capacity / Load (Btu/h)

  • ^
  • | BUILDING HEATING LOAD LINE
  • | (Increases as Outdoor Temp Drops)
  • | /
  • | / HEAT PUMP HEATING CAPACITY CURVE
  • | / (Decreases as Outdoor Temp Drops)
  • | / .-'
  • | / .-'
  • | / .-'
  • | X <================ THERMAL BALANCE POINT (e.g., 30°F)
  • | .-' \
  • | .-' \
  • | .-' \
  • +----------------------------------------------------> Outdoor Temp (°F)
  • 0°F 14°F 30°F 50°F 70°F
  • [DEFICIT COVERED] [HEAT PUMP COVERS 100% OF HEATING]
  • [BY ELECTRIC HEAT]
  • The Thermal Balance Point

As outdoor temperatures fall, two simultaneous phenomena occur:

The building heating load increases linearly because the indoor-to-outdoor temperature difference ( Δ T \Delta T Δ T ) widens.

The heat pump's heating capacity decreases because the outdoor air becomes less dense and contains fewer extractable thermal units, reducing suction pressure and compressor mass flow rate.

The Thermal Balance Point is the precise outdoor temperature at which the heat pump's diminishing heating output matches the structure's increasing heat loss. In Arkansas (Climate Zones 3A/4A), a properly sized heat pump exhibits a thermal balance point between 28°F and 35°F .

Supplemental and Emergency Auxiliary Heat

Above the Thermal Balance Point : The heat pump provides 100% of the building's heating requirements at high coefficients of performance (COP between 2.5 and 3.8), operating at a fraction of the cost of electric resistance heat.

Below the Thermal Balance Point : The heat pump continues to run, but its output cannot satisfy the thermostat. Supplemental electric resistance heat strips (or a gas furnace in a dual-fuel system) cycle on to bridge the deficit between heat pump capacity and total building heat loss.

Emergency Heat : In the event of a primary compressor failure, the auxiliary heat strips must be sized to handle 100% of the design heating load at winter 99% design conditions.

Sizing Rules for Heat Pumps

If an HVAC contractor sizes an air-source heat pump to handle 100% of the winter heating load down to Fayetteville's 14°F design condition, the unit's cooling capacity will exceed the summer cooling load by 50% to 100%. During summer, this grossly oversized compressor will short-cycle, causing severe indoor humidity spikes.

Therefore, ACCA Manual S mandates: Size the heat pump to satisfy the cooling load within the 90% to 115% limit (or up to 120% where heating governs) . Any heating deficit occurring below the thermal balance point must be supplied by staged auxiliary supplemental heat rather than an oversized refrigeration compressor.

Fossil-Fuel Furnace Sizing (100% to 140% Rule)

For natural gas and propane warm-air furnaces, ACCA Manual S establishes that the AFUE output heating capacity (not the gross input rating) must be between 100% and 140% of the Manual J design heating load: 1.00 × Q heating ≤ Furnace Output Capacity ≤ 1.40 × Q heating 1.00 \times Q_{\text{heating}} \le \text{Furnace Output Capacity} \le 1.40 \times Q_{\text{heating}} 1.00 × Q heating ​ ≤ Furnace Output Capacity ≤ 1.40 × Q heating ​

Practical Sizing Example

Consider a home in Little Rock with a calculated Manual J heating load of 42,000 Btu/h :

Minimum allowable output : 1.00 × 42 , 000 = 42 , 000 Btu/h 1.00 \times 42,000 = 42,000 \text{ Btu/h} 1.00 × 42 , 000 = 42 , 000 Btu/h

Maximum allowable output : 1.40 × 42 , 000 = 58 , 800 Btu/h 1.40 \times 42,000 = 58,800 \text{ Btu/h} 1.40 × 42 , 000 = 58 , 800 Btu/h

If a contractor evaluates a 96% AFUE condensing gas furnace with a nominal 60,000 Btu/h input: Actual Heating Output = 60 , 000 × 0.96 = 57 , 600 Btu/h \text{Actual Heating Output} = 60,000 \times 0.96 = 57,600 \text{ Btu/h} Actual Heating Output = 60 , 000 × 0.96 = 57 , 600 Btu/h

Because 57,600 Btu/h falls comfortably below the 58,800 Btu/h upper limit ( 57 , 600 / 42 , 000 = 137.1 % 57,600 / 42,000 = 137.1\% 57 , 600/42 , 000 = 137.1% ), this model complies with ACCA Manual S. If the contractor had proposed an 80,000 Btu/h input furnace (output = 76,800 Btu/h, or 183% of load), the submittal would be rejected as a code violation under the Arkansas Mechanical Code.

The Minimum Model Size Exception

Manual S provides an exception: if the smallest heating unit available in the contractor's selected manufacturer product line produces an output greater than 140% of the design heating load, a furnace with an output up to 200% of the load is permissible. However, the contractor must prove that no smaller heating capacity unit exists within that product family.

Pitfalls of System Oversizing and Undersizing in Arkansas

  • System Metric Severely Oversized System (>115-120% Cooling) Severely Undersized System (<90% Capacity)
  • Runtime Cycles Short, rapid cycles (5 to 8 minutes) Continuous 24-hour operation on design days

Indoor Relative Humidity High (60% to 75% RH) ; cool but clammy air Normal to low; long runtimes maximize moisture removal

Comfort & Temperature Drastic temperature swings, cold drafts Temperature drifts upward during peak afternoon hours

Acoustics & Duct Velocity Excessive static pressure, whistling grilles Quiet airflow; low air velocity

Equipment Reliability Severe mechanical wear from frequent starts/stops; heat exchanger thermal stress Premature motor burnouts from zero rest cycles

Indoor Air Quality Microbial / fungal growth in ductwork and walls Inadequate fresh air delivery if cycling fails

Loading diagram... ACCA Manual S Equipment Selection and Verification Flowchart