Study guide
14.3 Material, Labor & Bid Estimating
Arkansas HVAC/R Contractor License Exam
Track your progress as you read
Finished sections get a check mark.
1 Arkansas HVAC/R Licensing Law, Board Rules & Administration
1.1 Arkansas HVAC/R Board Authority, Statutes & Definitions 1.2 License Classifications & Capacity Limitations 1.3 Registrant Requirements, Apprenticeship & Experience Verification 1.4 License Renewal, Continuing Education & Disciplinary Actions
2 HVAC Thermodynamics, Psychrometrics & Gas Laws
2.1 Principles of Heat Transfer & Thermodynamic Fundamentals 2.2 Psychrometric Chart Dynamics & Air Properties 2.3 Psychrometric Processes & Air Mixture Calculations 2.4 Gas Laws Applied to HVAC/R Systems
3 Heating and Cooling Load Calculations (Manual J & S)
3.1 ACCA Manual J Design Conditions & Thermal Envelopes 3.2 Peak Cooling Load Calculations: Sensible vs. Latent Heat Gain 3.3 Heating Load Calculations & Infiltration Rates 3.4 ACCA Manual S Equipment Selection & Verification
4 Ductwork Design, Sizing & SMACNA Standards (Manual D)
4.1 ACCA Manual D Airflow Fundamentals & External Static Pressure 4.2 Equal Friction & Static Regain Duct Sizing Methods 4.3 Duct Fittings, Equivalent Length & Dynamic Losses 4.4 SMACNA Duct Construction Standards & Joint Sealing
5 Air Distribution, Balancing & Ventilation Codes
5.1 Supply & Return Air Distribution Hardware (Grilles, Registers, Diffusers) 5.2 System Airflow Testing, Adjusting & Balancing (TAB) 5.3 Ventilation Standards: ASHRAE 62.1, 62.2 & 2021 IMC Ventilation Air
6 Mechanical Refrigeration Cycle & Components
6.1 The Vapor-Compression Refrigeration Cycle 6.2 Compressors & Operating Characteristics 6.3 Condensers & Evaporators 6.4 Metering Devices & Refrigerant Flow Controls 6.5 Refrigerant Line Sizing, Oil Return & Field Piping Practices
7 Refrigerants, Oils & EPA Section 608 Regulations
7.1 Refrigerant Chemistry, ASHRAE Standard 34 & A2L Transition 7.2 Lubricating Oils & System Compatibility 7.3 EPA Section 608 Regulatory Mandates & Recovery Standards 7.4 System Evacuation, Dehydration & Leak Detection
8 Air Conditioning & Heat Pump Systems
8.1 Residential & Commercial Split Systems and Package RTUs 8.2 Air-Source Heat Pumps & The Reversing Valve 8.3 Supplemental & Emergency Heating Systems 8.4 Dual-Fuel & Geothermal (Ground-Source) Heat Pump Systems
9 Gas Furnaces, Combustion Air & Venting (IFGC / IMC)
9.1 Gas Furnace Types, AFUE Ratings & Sequence of Operation 9.2 Gas Burners, Ignition Systems & Flame Safeguard Controls 9.3 Combustion Air Requirements (IFGC Chapter 3 / IMC Chapter 7) 9.4 Flue Gas Venting & Category I-IV Venting Systems
10 Boilers, Hydronics & Fuel Gas Piping
10.1 Hydronic Heating Systems, Low-Pressure Boilers & ASME Code 10.2 Hydronic Distribution, Circulator Pumps & Piping Loops 10.3 Fuel Gas Piping Materials, Sizing & Pressure Testing (IFGC Chapter 4) 10.4 Gas Regulators, Manifold Pressure & Gas Meter Sizing 10.5 Condensate Disposal, Piping Support & Mechanical Insulation
11 Electrical Fundamentals, Motors & Control Circuits
11.1 HVAC Electrical Fundamentals, Ohm's Law & Power Calculations 11.2 Single-Phase & Three-Phase Electric Motors in HVAC 11.3 Low-Voltage Control Circuits & Thermostats
12 National Electrical Code (NEC) for HVAC Equipment
12.1 NEC Article 440: Hermetic Refrigerant Motor-Compressors & Branch Circuits 12.2 Equipment Disconnecting Means & Overcurrent Protective Devices (OCPD) 12.3 Motor Branch Circuit Sizing & Conductor Ampacity (NEC Article 430 & Tables)
13 System Maintenance, Troubleshooting & Safety Standards
13.1 Systematic Mechanical & Electrical Troubleshooting 13.2 Airflow & Refrigerant Charge Diagnostics 13.3 Jobsite Safety, OSHA Standards & Personal Protective Equipment
14 Plan Reading, Estimating & HVAC/R Trade Math
14.1 Mechanical Plan Symbols, Schedules & Abbreviations 14.2 Architectural Scales, Dimensions & Quantity Takeoff 14.3 Material, Labor & Bid Estimating 14.4 Applied HVAC/R Trade Math & Unit Conversions
14.3 Material, Labor & Bid Estimating
Key Takeaways Explain This Topic AI
A bid is built from direct costs (material, labor, equipment, subcontractors), plus job overhead, plus a share of general overhead, plus profit — omitting any layer produces a bid that wins work and loses money.
Labor is estimated with labor units, which are standard installation hours per unit of work, multiplied by quantity and adjusted for job conditions such as height, occupied buildings, and congested ceilings.
The labor burden — payroll taxes, workers compensation, general liability, and benefits — is added on top of the base wage and commonly runs 25 to 40 percent, so a $28 wage costs the contractor roughly $35 to $39 per hour.
Markup and margin are not the same: markup is figured on cost while margin is figured on selling price, so a 20 percent markup yields only about a 16.7 percent margin and a 20 percent margin requires a 25 percent markup.
Selling price for a target margin is cost divided by (1 minus the margin), so $10,000 of cost at a 20 percent target margin must sell for $12,500, not $12,000.
Last updated: September 2026
14.3 Material, Labor & Bid Estimating
Important
Why a licensing exam tests estimating : A Class A license authorizes unlimited-capacity contracting. The Board's interest is that licensees be competent to run a business that will still exist when the warranty is called. Chronic underbidding is a leading cause of contractor failure and of abandoned, unfinished mechanical work. The Plan Reading, Estimating & Math subject area tests the arithmetic that separates a bid from a guess.
Anatomy of a Bid
A complete bid is assembled in layers. Each layer is a distinct question, and skipping any one of them produces a number that looks competitive and is not.
Layer What it contains Typical failure
1. Direct material Everything permanently installed: equipment, duct, pipe, fittings, insulation, hangers, grilles, controls, refrigerant Forgetting consumables and hardware
2. Direct labor Field hours to install the above, fully burdened Using the base wage instead of the burdened rate
- 3. Equipment & tools Crane picks, lifts, rigging, welders, scaffolding Omitting the crane for rooftop units
- 4. Subcontractors Balancing, controls, crane service, roofing, electrical Assuming another trade covers it
5. Job overhead Permits, plan review, dumpsters, temp power, jobsite supervision, mobilization, project management, bonds, jobsite-specific insurance Treating supervision as free
6. General overhead The share of office rent, estimating, vehicles, software, accounting, and non-billable staff this job must carry Not allocating it at all
7. Profit Return on the risk of performing the work Confusing markup with margin
Direct cost is layers 1–4. Total cost is layers 1–6. Selling price is total cost plus profit.
Estimating Labor with Labor Units
Material quantities come straight from the takeoff. Labor does not — it is derived by applying a labor unit , the standard number of installation hours for one unit of work, drawn from a published manual or from the contractor's own historical production data.
Representative form (always use your own or your manual's figures on a real bid):
- Item Unit Labor unit (hours)
- Rectangular duct, fabricated and installed per 100 lb varies by gauge and height
- Round spiral duct, 8 in. per linear ft fractional
- Ceiling diffuser, lay-in each fractional
- Rooftop unit, 10 ton, set and connected each multiple hours
- Refrigerant line set, brazed per linear ft fractional
- Labor hours = quantity × labor unit × condition factors
- Condition Factors
Published labor units assume favorable conditions: new construction, ground floor, open ceiling, normal working hours, cooperative sequencing. Real jobs deviate, and the estimator applies multipliers:
Working height. Work above roughly 10–12 feet requires lifts and slows materially; the multiplier grows with height.
Occupied buildings. Retrofit work in an operating facility carries protection, cleanup, and coordination penalties.
Congested ceiling cavities. Ductwork threading between sprinkler mains, cable tray, and structure takes far longer than an open plenum.
Off-hours or shift work. Night and weekend work carries both a premium wage and a productivity penalty.
Crew size and learning curve. Repetitive work gets faster; one-off work does not.
Weather. Arkansas summer rooftop work in July has a real, measurable productivity loss.
Caution
Condition factors are multiplied, not added. A job that is 15% slower for height and 20% slower for occupancy is 1.15 × 1.20 = 1.38 , a 38% labor penalty — not 35%.
The Fully Burdened Labor Rate
The wage on the technician's paycheck is not what the hour costs the company. Labor burden adds:
- Employer FICA (Social Security and Medicare)
- Federal and state unemployment tax
Workers' compensation insurance — significant in the mechanical trades and a required coverage for Arkansas employers with three or more employees
General liability insurance allocable to payroll — Arkansas HVAC/R licensees must carry at least $250,000 in general liability coverage
Health insurance, retirement contributions, paid time off
Training, licensing, and continuing education — including the 8 hours of board-approved CE per International Mechanical Code cycle required under 17 CAR § 261-120
Vehicle, fuel, and small-tool allowance where charged to labor rather than overhead
Burden commonly lands between 25% and 40% of base wage.
Tip
Worked burdened rate. Base wage $28.00/hr , burden 32% .
Burdened cost = 28.00 × 1.32 = $36.96/hr .
On a 400-hour job, estimating at the bare wage understates labor cost by 400 × (36.96 − 28.00) = $3,584 . That single omission can exceed the entire profit on a small commercial project.
Job Overhead vs. General Overhead
These are distinct and are handled differently.
Job overhead is caused by this job and is estimated directly for it: the mechanical permit, plan review, jobsite supervision hours, mobilization, temporary power and heat, dumpsters, jobsite trailer, project management time, and any bond required for the project. In Arkansas, remember that a commercial project of $50,000 or more requires an Arkansas Contractors Licensing Board commercial license in addition to the ADLL trade license, and ACLB licensure carries its own bonding and financial-statement obligations that belong in this layer.
General overhead is the cost of being in business regardless of any one job: office rent and utilities, estimating and administrative salaries, accounting and legal, insurance not allocable to a job, software, vehicles, marketing, and annual license renewals. It is allocated across all jobs, most often as a percentage of direct cost or of direct labor.
Tip
Worked overhead allocation. A contractor's annual general overhead is $300,000 and expected annual direct cost is $1,500,000 . Overhead allocation rate = 300,000 ÷ 1,500,000 = 20% of direct cost .
A job with $40,000 of direct cost must therefore carry 40,000 × 0.20 = $8,000 of general overhead before any profit is added.
Markup vs. Margin — The Central Arithmetic Trap
This distinction appears on trade licensing exams more often than any other estimating topic, because contractors get it wrong in the field constantly.
- Markup is computed on cost : Price = Cost × (1 + markup)
- Margin (gross profit percentage) is computed on selling price : Margin = (Price − Cost) ÷ Price
They are not interchangeable.
Tip
Worked comparison at $10,000 of total cost.
Applying a 20% markup: Price = 10,000 × 1.20 = $12,000 Gross profit = $2,000
Margin = 2,000 ÷ 12,000 = 16.7% — not 20%.
- Achieving a 20% margin: Price = Cost ÷ (1 − margin) = 10,000 ÷ 0.80 = $12,500 Gross profit = $2,500
- Check: 2,500 ÷ 12,500 = 20% ✓
The required markup was 2,500 ÷ 10,000 = 25% .
The formula to memorize:
Selling price = Total cost ÷ (1 − desired margin)
- Desired margin Required markup on cost
- 10% 11.1%
- 15% 17.6%
- 20% 25.0%
- 25% 33.3%
- 33.3% 50.0%
- 50% 100.0%
A contractor who believes a 20% markup delivers a 20% margin is short 3.3 percentage points on every job — which, on a business running an 8% net, is most of the profit.
Full Worked Bid
A 10-ton rooftop replacement on a single-story Arkansas retail building.
- Layer Calculation Amount
- Equipment (RTU-1, 10 ton) from schedule and quote $14,200
- Curb adapter, duct transitions, hardware takeoff $1,850
- Refrigerant, controls, misc. material takeoff $700
- Direct material subtotal $16,750
- Labor: 62 hours × $36.96 burdened 62 × 36.96 $2,292
- Condition factor (rooftop, occupied store): × 1.25 2,292 × 1.25 $2,865
- Crane pick (subcontract) quote $1,400
- Test and balance (subcontract) quote $850
- Direct cost (layers 1-4) 16,750 + 2,865 + 1,400 + 850 $21,865
- Job overhead: permit, supervision, disposal, protection direct estimate $1,600
- General overhead at 20% of direct cost 21,865 × 0.20 $4,373
- Total cost (layers 1-6) 21,865 + 1,600 + 4,373 $27,838
- Selling price at a 20% target margin 27,838 ÷ 0.80 $34,798
- Gross profit 34,798 − 27,838 $6,960
- Margin check 6,960 ÷ 34,798 20.0% ✓
Note what a 20% markup would have produced instead: 27,838 × 1.20 = $33,406, a margin of 16.7% and $1,392 less profit on one small job.
Common Exam Traps
Trap: Markup equals margin. They never do. Price = Cost ÷ (1 − margin).
Trap: Bare wage as labor cost. Always burden the wage.
Trap: Adding condition factors. They multiply.
Trap: Overhead omitted. General overhead must be allocated to every job or it is paid out of profit.
Trap: Forgetting the ACLB threshold. A commercial job at $50,000 or more (or a residential job at $2,000 or more ) requires ACLB licensure in addition to the ADLL trade license — a compliance cost that belongs in the bid.
Trap: Subcontractor scope gaps. Balancing, crane service, roofing penetrations, and electrical are frequently assumed to be someone else's; confirm in writing.