Study guide

Signal Processing: Demodulation, Rejection & Pre/Post-Processing

ARDMS SPI Sonography Principles & Instrumentation

Track your progress as you read

Finished sections get a check mark.

1 Introduction & the SPI Exam

What the SPI Is & Why Physics Matters The V24.1 Content Outline & How to Study It Math, Units & Decibels You Must Know

2 Properties of Ultrasound Waves

Sound as a Mechanical Longitudinal Wave Period, Frequency & Wavelength Propagation Speed & the Wavelength Equation Amplitude, Power & Intensity

3 Pulsed Ultrasound

Continuous vs Pulsed Wave; PRF & PRP Pulse Duration, Spatial Pulse Length & Duty Factor Bandwidth, Q-Factor & Damping

4 Interaction of Sound with Tissue

Attenuation: Absorption, Reflection & Scattering The Attenuation Coefficient & Half-Value Layer Acoustic Impedance & Reflection Refraction, Snell's Law & the Range Equation

5 Transducers & Sound Beams

Construction & the Piezoelectric Effect The Sound Beam: Near/Far Field & Focusing Array Transducers Transducer Selection, Frequency Trade-offs & Nonimaging Probes

6 Resolution

Axial Resolution Lateral & Elevational Resolution Temporal Resolution & Frame Rate

7 Pulse-Echo Instrumentation & the Imaging Chain

Beam Former, Pulser & Output Power The Receiver: Amplification & Time-Gain Compensation Dynamic Range & Compression Signal Processing: Demodulation, Rejection & Pre/Post-Processing Scan Converter, Display & Image Storage

8 Display Modes & Image-Optimization Features

A-Mode, B-Mode & M-Mode Harmonic Imaging Spatial & Frequency Compounding, Panoramic Imaging 3D/4D Imaging & Contrast Agents

9 Doppler Principles & Instrumentation

The Doppler Effect, Shift & Equation The Doppler Angle & Cosine Continuous-Wave Doppler Pulsed-Wave Doppler, Sample Volume & Nyquist Limit Aliasing & How to Eliminate It Spectral Doppler Analysis & Waveforms Color & Power Doppler Hemodynamics & Doppler Measurements

10 Artifacts

Propagation Artifacts Attenuation & Beam-Width Artifacts Doppler & Color Artifacts

11 Bioeffects, Safety & Quality Assurance

Bioeffects Mechanisms: Thermal & Cavitation Thermal & Mechanical Index & ALARA Quality Assurance & Tissue-Mimicking Phantoms Statistical Parameters: Sensitivity, Specificity & Predictive Value Patient Care, Ergonomics, Infection Control & Workflow

Signal Processing: Demodulation, Rejection & Pre/Post-Processing

Key Takeaways Explain This Topic AI

Pre-processing functions are applied to the signal before it is stored in scan-converter memory and cannot be changed afterward; post-processing functions are applied after storage and can be adjusted on a frozen image.

Write zoom re-scans the region of interest at higher line density before storage, genuinely improving resolution within the zoomed area.

Read zoom magnifies already-stored pixels after the fact and does not add new resolution or information.

Persistence (frame averaging) blends consecutive frames to reduce noise and speckle but reduces temporal resolution for fast-moving structures.

Frequency compounding combines images acquired using multiple frequency bands to reduce speckle noise.

Last updated: July 2026

Overview: Pre-Processing vs. Post-Processing

Before a returning echo signal becomes a pixel on the screen, it passes through a series of signal-processing steps. SPI groups these into two broad categories:

Category When it happens Can it be changed after the image is frozen/stored?

Pre-processing Applied to the signal before it is stored in the scan converter's image memory No — pre-processing choices are "baked in" to the stored image data

Post-processing Applied to the image data after it is stored in the scan converter's image memory Yes — post-processing can be adjusted on a frozen or previously acquired image, including on a stored/reviewed image

Nearly every function in this section can be classified as pre- or post-processing, and SPI regularly tests which category a given function belongs to.

Demodulation and Rejection

Demodulation converts the raw, high-frequency radiofrequency (RF) echo signal into a usable video signal. It has several sub-steps, including amplification (Section 7.2), compression (Section 7.3), and rectification (converting the RF waveform, which has both positive and negative voltage swings, into an all-positive envelope that represents echo amplitude over time). Demodulation happens early, before the signal reaches the scan converter, and is therefore a pre-processing function.

Rejection (sometimes called suppression) is a receiver function that eliminates low-amplitude signals below a chosen threshold — typically electronic noise or very weak scatter — so they do not appear on the display as unwanted low-level gray "haze." Raising rejection cleans up the image by removing faint noise, but rejection set too high can also discard genuine weak echoes; it is generally classified as pre-processing since it acts on the signal before scan conversion.

Read Zoom vs. Write Zoom

Zoom magnifies a region of interest, but SPI distinguishes two very different mechanisms:

Write zoom (also called "true" or "research" zoom) is applied before the scan converter writes the image into memory: the sonographer selects a region of interest and the system re-scans that region using a higher scan-line density, actually acquiring more data points to fill the zoomed region. Because it changes what data is written to memory, write zoom is a pre-processing function, and it genuinely improves detail/resolution within the zoomed region.

Read zoom (also called "pan" zoom) is applied after the image is already stored in scan-converter memory: the system simply magnifies the existing stored pixels, enlarging them on the display. Because it only reads and re-displays already-stored data, read zoom is a post-processing function, and it does not add new information or improve resolution — it only makes existing pixels bigger (similar to zooming in on a digital photo, which can produce a blocky/pixelated look at high magnification).

Gray-Scale Maps

A gray-scale map (also called a gray-scale curve or transfer curve) is the function that assigns a specific shade of gray to each possible echo-amplitude value after dynamic range compression (Section 7.3). Different preset gray-scale maps emphasize different parts of the amplitude range — for example, one map might favor contrast in low-amplitude (weak echo) regions, while another favors contrast in high-amplitude (strong echo) regions. Because gray-scale maps are typically adjustable on a stored/frozen image, they are classified as a post-processing function.

Persistence (Frame Averaging)

Persistence , also called frame averaging or temporal compounding , is a post-processing technique that blends several consecutive image frames together before displaying the composite. Because random noise varies frame-to-frame while real anatomic structures remain consistent across frames, averaging frames together smooths out noise and speckle, producing a less "grainy" image. The trade-off is temporal resolution: high persistence blurs rapid motion (because it blends frames spanning a longer time interval), so persistence should be reduced when imaging fast-moving structures such as a beating fetal heart or valve leaflets.

Edge Enhancement

Edge enhancement is a processing technique that increases the amplitude difference at boundaries between adjacent structures with different echogenicity, making borders/edges appear sharper and more distinct. It works by exaggerating amplitude transitions rather than adding new anatomic information, improving the subjective visibility of a boundary such as an organ capsule or a mass margin.

Frequency Compounding

Frequency compounding transmits and/or processes multiple different frequency bands (rather than a single frequency) from the same location and combines the resulting images into a single composite frame. Because each frequency band produces slightly different speckle and interference patterns, averaging across bands reduces speckle noise and improves overall image uniformity — a mechanism distinct from spatial compounding (Chapter 8), which instead combines images acquired from multiple beam-steering angles .

Summary Table: Classifying Each Function

  • Function Pre- or Post-Processing Primary Effect
  • Demodulation/rectification Pre Converts RF signal to usable video envelope
  • Rejection Pre Removes low-level noise below a threshold
  • Write zoom Pre Re-scans region at higher line density — true resolution gain
  • Read zoom Post Magnifies stored pixels — no new resolution
  • Gray-scale map Post Reassigns amplitude-to-gray-shade mapping
  • Persistence (frame averaging) Post Smooths noise/speckle; reduces temporal resolution
  • Edge enhancement Post Sharpens borders between structures
  • Frequency compounding Pre (acquisition-based) Reduces speckle by combining frequency bands

Mastering the pre-/post-processing split, and especially the read-zoom-vs-write-zoom distinction, directly covers Domain 3 tasks 3.E (magnification), 3.M (gray scale, frequency compounding, persistence), and 3.N (edge enhancement).