Study guide

Period, Frequency & Wavelength

ARDMS SPI Sonography Principles & Instrumentation

Track your progress as you read

Finished sections get a check mark.

1 Introduction & the SPI Exam

What the SPI Is & Why Physics Matters The V24.1 Content Outline & How to Study It Math, Units & Decibels You Must Know

2 Properties of Ultrasound Waves

Sound as a Mechanical Longitudinal Wave Period, Frequency & Wavelength Propagation Speed & the Wavelength Equation Amplitude, Power & Intensity

3 Pulsed Ultrasound

Continuous vs Pulsed Wave; PRF & PRP Pulse Duration, Spatial Pulse Length & Duty Factor Bandwidth, Q-Factor & Damping

4 Interaction of Sound with Tissue

Attenuation: Absorption, Reflection & Scattering The Attenuation Coefficient & Half-Value Layer Acoustic Impedance & Reflection Refraction, Snell's Law & the Range Equation

5 Transducers & Sound Beams

Construction & the Piezoelectric Effect The Sound Beam: Near/Far Field & Focusing Array Transducers Transducer Selection, Frequency Trade-offs & Nonimaging Probes

6 Resolution

Axial Resolution Lateral & Elevational Resolution Temporal Resolution & Frame Rate

7 Pulse-Echo Instrumentation & the Imaging Chain

Beam Former, Pulser & Output Power The Receiver: Amplification & Time-Gain Compensation Dynamic Range & Compression Signal Processing: Demodulation, Rejection & Pre/Post-Processing Scan Converter, Display & Image Storage

8 Display Modes & Image-Optimization Features

A-Mode, B-Mode & M-Mode Harmonic Imaging Spatial & Frequency Compounding, Panoramic Imaging 3D/4D Imaging & Contrast Agents

9 Doppler Principles & Instrumentation

The Doppler Effect, Shift & Equation The Doppler Angle & Cosine Continuous-Wave Doppler Pulsed-Wave Doppler, Sample Volume & Nyquist Limit Aliasing & How to Eliminate It Spectral Doppler Analysis & Waveforms Color & Power Doppler Hemodynamics & Doppler Measurements

10 Artifacts

Propagation Artifacts Attenuation & Beam-Width Artifacts Doppler & Color Artifacts

11 Bioeffects, Safety & Quality Assurance

Bioeffects Mechanisms: Thermal & Cavitation Thermal & Mechanical Index & ALARA Quality Assurance & Tissue-Mimicking Phantoms Statistical Parameters: Sensitivity, Specificity & Predictive Value Patient Care, Ergonomics, Infection Control & Workflow

Period, Frequency & Wavelength

Key Takeaways Explain This Topic AI

Period and frequency are reciprocals of one another: period = 1/frequency.

A 5 MHz transducer produces a period of 0.2 microseconds (0.2 µs).

The audible range for human hearing is approximately 20 Hz to 20 kHz; ultrasound is defined as any sound frequency above 20 kHz (20,000 Hz).

Diagnostic medical ultrasound uses frequencies in the range of approximately 2 to 15 MHz.

Frequency is determined entirely by the sound source (the transducer) and does not change as the sound wave passes into a different medium.

Last updated: July 2026

Frequency: How Many Cycles Per Second

Frequency is the number of complete cycles (one full compression plus one full rarefaction) that occur in one second, measured in hertz (Hz) . One hertz equals one cycle per second. Because diagnostic ultrasound frequencies are so high, they are almost always expressed in megahertz (MHz) — one MHz equals one million cycles per second (1,000,000 Hz). Frequency is a source-determined property : it is set by how fast the piezoelectric crystal inside the transducer vibrates (governed largely by crystal thickness, covered in Chapter 5), not by anything in the tissue the sound later travels through. A critical rule to memorize now, because it resurfaces constantly later in the course: frequency does not change as sound passes from one medium into another. A 5 MHz pulse leaving the transducer is still a 5 MHz pulse deep in the liver.

Period: The Reciprocal of Frequency

Period is the time required to complete one full cycle — essentially the "clock" version of frequency. Period and frequency are reciprocals of one another:

  • Quantity Formula Notes
  • Period Period = 1 / Frequency Time for one cycle; units of time (seconds, µs)
  • Frequency Frequency = 1 / Period Cycles per second; units of Hz

Because they are reciprocals, period and frequency always move in opposite directions : as frequency goes up, period goes down, and vice versa. This is a purely mathematical relationship — it holds regardless of what medium the sound is traveling through, because (like frequency) period is fixed by the source and does not change with the medium.

Worked Example

A transducer operating at 5 MHz produces a period of:

Period = 1 / frequency = 1 / 5,000,000 Hz = 0.0000002 seconds = 0.2 microseconds (µs)

Memorize this exact pair (5 MHz ↔ 0.2 µs) — it is one of the most frequently tested numerical relationships on the SPI exam, and the same reciprocal logic applies to any frequency the exam gives you (a 2 MHz transducer produces a 0.5 µs period, a 10 MHz transducer produces a 0.1 µs period, and so on).

Practice: Period at Common Diagnostic Frequencies

The reciprocal relationship holds at every frequency an exam question might use. Practicing the arithmetic at a range of common diagnostic frequencies builds the speed you need for timed testing:

  • Frequency Period (1/frequency)
  • 2 MHz 0.5 µs
  • 2.5 MHz 0.4 µs
  • 3.5 MHz ~0.286 µs
  • 5 MHz 0.2 µs
  • 7.5 MHz ~0.133 µs
  • 10 MHz 0.1 µs

Notice the pattern: as frequency climbs, period keeps shrinking, but the two values never move independently — one is always simply 1 divided by the other, regardless of the medium the sound is currently passing through.

Where Ultrasound Sits on the Frequency Spectrum

"Ultrasound" is simply a name for sound whose frequency is too high for humans to hear:

Range Frequency Audible to humans?

  • Infrasound Below 20 Hz No (too low)
  • Audible sound 20 Hz – 20 kHz (20,000 Hz) Yes
  • Ultrasound Above 20 kHz (20,000 Hz) No (too high)
  • Diagnostic medical ultrasound ~2–15 MHz No

Notice the enormous gap between the technical definition of ultrasound (anything above 20 kHz) and the frequencies actually used for diagnostic imaging (2–15 MHz, i.e., 2,000,000–15,000,000 Hz). Frequencies barely above 20 kHz are used in industrial and some flow-detection applications, but diagnostic B-mode and Doppler imaging require much higher frequencies than the bare minimum "ultrasound" threshold in order to achieve adequate axial resolution (a relationship explored fully in Chapter 6).

Wavelength: The Spatial Companion to Period

While period and frequency describe the time dimension of a wave cycle, wavelength describes its spatial dimension — the physical distance over which one complete cycle (one compression plus one rarefaction) occurs, typically measured in millimeters. Wavelength is not fixed by the source alone; it also depends on how fast sound is moving through the specific medium it is currently in. Because propagation speed changes tissue-to-tissue while frequency stays constant, wavelength is the variable that changes when sound crosses from one tissue type into another. The full equation linking wavelength, frequency, and propagation speed — and the clinically useful shortcut for calculating wavelength in soft tissue — is covered in the next section (2.3), where you will need today's period/frequency relationship as a foundation.

SPI Exam Tip

Expect the exam to test period/frequency reciprocity in multiple disguises: "what happens to the period if frequency increases?" or a direct calculation ("a 4 MHz transducer produces what period?"). Also expect at least one item testing whether frequency changes with medium — remember, it never does. The only source-independent property that changes when the wave enters a new tissue is propagation speed (and, as a downstream consequence, wavelength). Keep period, frequency, and the reciprocal relationship between them separate in your mind from propagation speed and wavelength, covered next — mixing up which quantities are fixed by the source and which are fixed by the medium is one of the most common ways candidates lose otherwise-easy points on this part of the exam.