Study guide
8.2 Soils, Geotechnical Reports, Bearing Capacity & Foundation Selection
ARE 5.0 Programming & Analysis PA
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview & Environmental Principles
1.1 ARE 5.0 PA Exam Structure, Scoring & Test-Taking Strategies 1.2 Climate Classification, Passive Solar Design & Microclimate Analysis 1.3 Natural Site Features, Shading Strategies & Daylight Analysis
2 Chapter 2: Environmental Constraints & Site Hazards
2.1 Floodplains, Wetlands & Hydrological Constraints 2.2 Contaminated Sites, Brownfields & Environmental Site Assessments (ESA) 2.3 Climate Resilience, Wildfire (WUI) & Sustainable Rating Systems (LEED)
3 Chapter 3: Building Codes: Occupancy & Construction Types
3.1 IBC 2021 Occupancy Classifications & Use Groups 3.2 Construction Types (Types I-V) & Fire-Resistance Ratings 3.3 Mixed Occupancy Strategies: Nonseparated, Separated & Accessory Uses
4 Chapter 4: Building Codes: Allowable Height, Area & Fire Protection
4.1 Building Height & Story Limitations (IBC Chapter 5) 4.2 Allowable Area Calculations & Frontage Increases (Equation 5-5) 4.3 Fire Walls, Fire Barriers, Fire Partitions & Smoke Barriers
5 Chapter 5: Accessibility Standards & Universal Design
5.1 Accessible Routes, Clear Floor Space, Turning Radius & Ramps (ADA / ICC A117.1) 5.2 Accessible Restrooms, Plumbing Fixtures & Signage 5.3 Accessible Parking, Van Spaces & Site Access Routes
6 Chapter 6: Means of Egress & Life Safety
6.1 Occupant Load Determinations (IBC Table 1004.5) 6.2 Egress Capacity, Exit Width & Stairway Design 6.3 Number of Exits, Travel Distances & Common Path of Travel
7 Chapter 7: Zoning Ordinances, Land Use & Entitlements
7.1 Zoning Classifications, Setbacks, Building Envelopes & Height Limits 7.2 Floor Area Ratio (FAR), Lot Coverage & Open Space Requirements 7.3 Parking Regulations, Loading Berths, Variances & Entitlement Approvals
8 Chapter 8: Topography, Geotechnical & Site Drainage
8.1 Contour Lines, Slope Calculations & Cut-and-Fill Grading 8.2 Soils, Geotechnical Reports, Bearing Capacity & Foundation Selection 8.3 Surface Hydrology, Runoff Calculations (Rational Method) & Stormwater / LID
9 Chapter 9: Site Documentation, Surveys & Contextual Analysis
9.1 Property Surveys, Legal Descriptions, Easements & Rights-of-Way 9.2 Historic Preservation, SHPO Reviews & Secretary of the Interior Standards 9.3 Vehicular & Pedestrian Circulation, Sight Triangles & Utility Infrastructure
10 Chapter 10: Building Programming Methodology & User Needs
10.1 Problem Seeking Methodology: 5 Steps & 4 Considerations 10.2 Determining Client & User Needs: Fact Gathering, Interviews & OPR 10.3 Functional Adjacencies, Bubble Diagrams & Matrix Analysis
11 Chapter 11: Space Standards, Area Calculations & Efficiency
11.1 Net Square Footage (NSF) vs. Gross Square Footage (GSF) & Efficiency Ratios 11.2 BOMA Floor Measurement Standards: Usable vs. Rentable Area & Load Factors 11.3 Space Allocation Standards, Unassigned Space & Grossing Factors
12 Chapter 12: Existing Facilities, Project Budget, Schedule & System Alternatives
12.1 Existing Building Evaluations, Adaptive Reuse & Hazardous Materials 12.2 Project Budgeting, Hard vs. Soft Costs & Cost Estimating Methods 12.3 Life-Cycle Cost Analysis (LCCA), Critical Path Scheduling & Phasing 12.4 Building, Structural & MEP System Alternatives for Programmatic Requirements
8.2 Soils, Geotechnical Reports, Bearing Capacity & Foundation Selection
Key Takeaways Explain This Topic AI
The Unified Soil Classification System (USCS, ASTM D2487) categorizes soils into coarse-grained (Gravel - G, Sand - S) and fine-grained (Silt - M, Clay - C, Organic - O), where well-graded soils (W) provide superior bearing and minimal settlement compared to poorly graded soils (P).
IBC Table 1806.2 establishes prescriptive allowable soil bearing pressures ranging from 12,000+ psf for crystalline bedrock, down to 3,000 psf for gravels, 2,000 psf for sands, and 1,500 psf for inorganic silts and clays.
Expansive clays (containing montmorillonite) undergo severe cyclic volumetric changes, swelling upon wetting and shrinking upon drying; mitigation requires deep drilled piers founded below the active zone and grade beams isolated by compressible carton void forms.
Standard Penetration Test (SPT) N-values quantify soil density and shear resistance: N < 4 indicates very soft/loose soil requiring ground improvement or deep foundations, while N > 50 indicates dense bearing strata or bedrock refusal.
Foundations divide into shallow systems (spread, strip, and mat/raft footings) for competent upper strata and deep systems (driven piles, drilled caissons, micropiles) that bypass weak, liquefiable, or expansive upper soils to reach dense load-bearing strata.
Last updated: September 2026
8.2 Soils, Geotechnical Reports, Bearing Capacity & Foundation Selection
Note
The Geotechnical Imperative : Every building is an earth-bound structure. Regardless of how sophisticated the superstructure may be, all dead, live, wind, and seismic forces ultimately resolve into the underlying geological strata. Understanding soil behavior, interpreting geotechnical boring logs, recognizing geohazards, and selecting appropriate foundation systems are essential core competencies tested on the ARE 5.0 Programming & Analysis division.
Soil is not a uniform manufactured material like steel or concrete; it is a complex, non-homogeneous, multi-phase natural aggregate consisting of mineral grains, organic matter, water, and air voids. Its engineering performance varies drastically across short distances and depths.
Soil Classifications: The Unified Soil Classification System (USCS)
Architects and civil engineers classify soils according to the Unified Soil Classification System (USCS) , codified under ASTM D2487 . The USCS categorizes soils based on particle size distribution (grain size) and plasticity characteristics. +-----------------------------------------------------------------------------------------+
- | Unified Soil Classification System (USCS) Matrix |
- +-----------------------------------------------------------------------------------------+
- | MAJOR DIVISION | SUBGROUP | USCS GROUP SYMBOLS & DESCRIPTIONS |
- | --------------------- | ------------------- | ----------------------------------------- |
- | **COARSE-GRAINED** | **Gravel (G)** | **GW**: Well-graded gravel, clean |
- | > 50% retained on | > 50% of coarse | **GP**: Poorly graded gravel, clean |
- | No. 200 sieve | fraction retained | **GM**: Silty gravel (fines with no/low PI)|
- | (0.075 mm) | on No. 4 sieve | **GC**: Clayey gravel (fines with plastic)|
- | | ------------------- | ----------------------------------------- |
- | | **Sand (S)** | **SW**: Well-graded sand, clean |
- | | > 50% of coarse | **SP**: Poorly graded sand, clean |
- | | fraction passes | **SM**: Silty sand (non-plastic fines) |
- | | No. 4 sieve | **SC**: Clayey sand (plastic fines) |
- | --------------------- | ------------------- | ----------------------------------------- |
- | **FINE-GRAINED** | **Silt (M)** | **ML**: Silt, Liquid Limit < 50 (lean) |
- | ≥ 50% passes | Low or no plasticity| **MH**: Silt, Liquid Limit ≥ 50 (elastic) |
- | No. 200 sieve | ------------------- | ----------------------------------------- |
- | (0.075 mm) | **Clay (C)** | **CL**: Lean clay, Liquid Limit < 50 |
- | | Cohesive, plastic | **CH**: Fat clay, Liquid Limit ≥ 50 (high)|
- | | ------------------- | ----------------------------------------- |
- | | **Organic (O)** | **OL**: Organic silt/clay, LL < 50 |
- | | Decomposing matter | **OH**: Organic silt/clay, LL ≥ 50 |
- | --------------------- | ------------------- | ----------------------------------------- |
- | **HIGHLY ORGANIC** | **Peat (Pt)** | Decomposed vegetable tissue, muck, peat; |
- | | | completely unsuitable for foundations. |
- +-----------------------------------------------------------------------------------------+
- 1. Coarse-Grained vs. Fine-Grained Soils
Coarse-Grained Soils (Gravels & Sands) : More than 50% of the dry soil weight is retained on the No. 200 sieve ( 0.075 mm 0.075\text{ mm} 0.075 mm ). Strength is governed by internal friction angle ( ϕ \phi ϕ ) , particle interlocking, and confining pressure. They are free-draining, settle almost instantaneously upon load application during construction, and exhibit low compressibility.
Fine-Grained Soils (Silts & Clays) : 50% or more passes through the No. 200 sieve. Behavior is governed by surface molecular charges, moisture content, and cohesion ( c c c ) rather than grain size. Settlement occurs slowly over years (consolidation settlement) as water is squeezed out of microscopic voids.
2. Well-Graded (W) vs. Poorly Graded (P)
Well-Graded Soils (GW, SW) : Contain a balanced distribution of all grain sizes from coarse to fine. Smaller grains nest tightly within the voids between larger particles, creating high density, superior shear strength, high load-bearing capacity, and minimal settlement.
Poorly Graded Soils (GP, SP) : Either have a uniform grain size (all particles roughly the same diameter) or a "gap-graded" distribution missing intermediate sizes. They contain large void spaces, lower shear strength, and higher susceptibility to settlement under vibrating machinery or seismic loads.
Soil Physics: Atterberg Limits & Plasticity
Fine-grained soils change consistency based on moisture content. In 1911, Swedish soil scientist Albert Atterberg established boundaries separating these moisture states: ATTERBERG CONSISTENCY STATES
- Solid State │ Semi-Solid State │ Plastic State │ Liquid State
- ──────────────┼──────────────────┼──────────────────┼──────────────► Moisture (%)
- ▲ ▲ ▲
- Shrinkage Limit Plastic Limit Liquid Limit
- (SL) (PL) (LL)
- ◄──────────────────►
- Plasticity Index
- (PI = LL - PL)
- 1. The Three Critical Limits
Liquid Limit (LL) : The moisture content (percentage) at which soil transitions from a plastic state to a viscous liquid state, capable of flowing under its own weight.
Plastic Limit (PL) : The moisture content at which soil transitions from a semi-solid to a plastic state. In the laboratory, it is the lowest moisture percentage at which the soil can be rolled by hand into a 1/8-inch (3.2 mm) diameter thread without crumbling.
Plasticity Index (PI) : The numerical difference between the Liquid Limit and the Plastic Limit: PI = LL − PL \text{PI} = \text{LL} - \text{PL} PI = LL − PL
2. Architectural Significance of the Plasticity Index (PI)
PI = 0 (Non-plastic) : Clean sands and coarse silts. Stable under varying moisture.
PI < 15 (Low to moderate plasticity) : Lean clays and clayey silts. Acceptable for conventional shallow foundations.
PI > 20–30 (High plasticity / Fat Clays - CH) : High volumetric instability. Indicates dangerous shrink/swell behavior under seasonal precipitation cycles, triggering severe foundation damage.
Soil Bearing Capacity & Prescriptive IBC Values (Table 1806.2)
Soil bearing capacity is the ability of the ground to support applied structural loads without shear failure (rupture) or intolerable settlement. In structural engineering, it is expressed as allowable bearing pressure ( q a q_a q a ) in pounds per square foot (psf). +-----------------------------------------------------------------------------------------+
- | IBC Table 1806.2 Prescriptive Allowable Bearing Pressures |
- +-----------------------------------------------------------------------------------------+
- | CLASS OF MATERIALS | ALLOWABLE BEARING PRESSURE (psf) |
- | -------------------------------------- | ---------------------------------------------- |
- | **1. Crystalline bedrock** | **12,000 psf** (sound granite, basalt, gneiss) |
- | **2. Sedimentary & foliated rock** | **4,000 psf** (shale, slate, hard limestone) |
- | **3. Sandy gravel and/or gravel** (GW, GP) | **3,000 psf** |
- | **4. Sand, silty sand, clayey sand** | **2,000 psf** (SW, SP, SM, SC) |
- | **5. Clay, sandy clay, silty clay,** | **1,500 psf** (CL, ML, MH, CH) |
- | **clayey silt, silt** | *(Prescriptive minimum code value)* |
- | **6. Peat, organic silt, organic clay**| **0 psf** *(Unsuitable; structural bypass req)*|
- +-----------------------------------------------------------------------------------------+
Warning
The Prescriptive Table Trap : IBC Table 1806.2 values may only be used in the absence of a site-specific geotechnical investigation for light, prescriptive structures. For commercial, multi-story, or institutional projects, a project geotechnical engineer must determine allowable bearing pressures via exploratory borings and laboratory shear testing.
Problem Soils & Geotechnical Hazards
Site analysis requires identifying treacherous soil conditions early in programming before schematic design locks in foundation costs.
1. Expansive Clays (Smectite / Montmorillonite)
Mechanism : Mineral lattice structures absorb water molecules between crystalline layers, expanding dramatically during rainy seasons (exerting upward swelling pressures of 10,000 to 25,000 psf—easily lifting residential and light commercial slabs). During dry droughts, they desiccate, shrink, and fissure, causing dramatic differential settlement.
The Active Zone : The upper soil layer subject to seasonal moisture fluctuations (typically 5 to 15 feet deep depending on climate).
Engineering Mitigation :
Drilled Concrete Piers & Grade Beams : Piers are drilled deep into non-swelling stable strata beneath the active zone, reinforced with tension steel to resist uplift friction.
Carton Void Forms : Biodegradable, corrugated paper box forms (void forms) placed directly beneath grade beams and pile caps. They support wet concrete during placement and subsequently absorb moisture and decompose, leaving a 4- to 6-inch physical void space. When the clay heaves, it expands upward into the void without imparting destructive pressure onto the structural frame.
Post-Tensioned (PT) Slabs : A stiff, heavily reinforced ribbed post-tensioned mat designed to float uniformly over swelling mounds without cracking.
2. Collapsible Soils (Hydro-compaction / Loess)
Mechanism : Wind-deposited silts (loess) and loose arid alluvium cemented loosely by clay bonds or calcium carbonate. In their dry state, they exhibit deceptively high bearing strength. However, when saturated with water (e.g., from broken water mains or landscape irrigation), the cementitious bonds dissolve, causing sudden, catastrophic structural collapse and subsidence.
Mitigation : Deep dynamic compaction, pre-wetting the site prior to construction, or deep foundation bypass.
3. Soil Liquefaction (Seismic Geohazard)
Mechanism : Occurs in saturated, loose, cohesionless soils (fine sands and silty sands) located below the water table during earthquake ground shaking. Cyclic shearing increases pore water pressure. When pore pressure equals the overburden weight, effective stress drops to zero. The soil loses all shear strength instantly, behaving as a dense liquid. Heavy buildings sink or tip over; underground tanks and utility pipes float to the surface.
Mitigation : Compaction grouting, vibro-replacement stone columns, dynamic deep compaction, or driving end-bearing piles down to non-liquefiable dense strata.
4. Frost-Susceptible Soils & Frost Heave (IBC Section 1809.5)
Mechanism : Not all freezing soils heave. Frost heave requires three conditions: (1) freezing air temperatures, (2) a shallow groundwater source, and (3) frost-susceptible soil —specifically silts (ML) and fine sands . Because silts have fine pores, they exert powerful capillary action , drawing unfrozen water upward toward the freezing line. As this water freezes, it forms expanding ice lenses , generating massive vertical heave forces.
Code Protection (IBC 1809.5) : Permanent building footings must extend below the statutory frost line established by the local jurisdiction (ranging from 0" in Southern Florida to 48"–72" in the upper Midwest/Northeast).
Alternative (ASCE 32) : Frost-Protected Shallow Foundations (FPSF) use rigid extruded polystyrene (XPS) insulation placed strategically around the exterior perimeter to harness geothermal heat from the earth, preventing frost from penetrating beneath shallow footings.
Geotechnical Report Components: Borings, SPT & Perc Tests
A Geotechnical Engineering Report provides empirical site-specific subsurface data. Architects must know how to interpret its primary sections: STANDARD PENETRATION TEST (SPT) LOG
- Depth (ft) Stratum Description N-Value (Blows/ft) Soil Consistency
- ────────── ───────────────────────── ─────────────────── ────────────────
- 0 - 3' Topsoil / Silty Loam -- Loose organic
- 3 - 8' Stiff Lean Clay (CL) 14 Stiff
- 8 - 14' Medium Dense Sand (SP) 22 Medium dense
- 14 - 22' Very Soft Organic Silt (OH) 2 UNSUITABLE (Weak)
- 22 - 35' Dense Gravelly Sand (GW) 45 Dense bearing
- 35'+ Bedrock Refusal (Granite) > 50 (100/3") Sound rock
- 1. Standard Penetration Test (SPT N-Value, ASTM D1586)
The SPT measures soil density and shear resistance in a borehole:
Procedure : A 140-pound hammer falls freely from a height of 30 inches onto a 2-inch outer-diameter split-spoon sampler. The sampler is driven 18 inches into the soil in three 6-inch increments.
The N-Value : The sum of hammer blows required to drive the sampler through the final 12 inches (increments 2 and 3). The first 6 inches is the "seating drive" and is discarded.
N-Value Benchmarks :
N < 4 : Very loose sand or very soft clay (severe settlement danger; shallow spread footings impossible).
N = 4 to 10 : Loose sand / medium clay (low bearing capacity, 1,000–2,000 psf).
N = 10 to 30 : Medium dense sand / stiff clay (suitable for standard spread footings, 2,500–4,000 psf).
N = 30 to 50 : Dense sand / hard clay (excellent bearing capacity, 5,000–8,000 psf).
N > 50 (or 50 blows for < 6 inches) : Refusal ; dense cemented stratum or bedrock.
2. Groundwater Table & Perched Water
Regional Water Table : The continuous upper boundary of saturated groundwater. High water tables trigger hydrostatic uplift (buoyancy) that can pop empty swimming pools or basement vaults out of the ground, and mandate continuous exterior waterproofing and sump pump dewatering.
Perched Water Table : A localized lens of groundwater trapped above an impermeable clay layer above the main regional aquifer. It can mislead initial excavations.
3. Percolation Test (Perc Test)
Purpose : Measures the rate at which soil absorbs water, calculated in Minutes Per Inch (MPI) .
Sanitary Application : Mandatory for designing on-site septic absorption drain fields:
Acceptable Range : Typically 15 to 60 minutes per inch .
Too Fast (< 5 min/inch) : Water drains too rapidly through coarse gravel without adequate microbiological filtration, contaminating groundwater aquifers.
Too Slow (> 60 min/inch) : Tight clays prevent absorption, causing untreated effluent to pond on the lawn surface.