Study guide
13.1 Domestic Water Supply & Pressure Boosting Systems
ARE 5.0 Project Planning & Design PPD
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview & Schematic Design Process
1.1 ARE 5.0 PPD Format, Scoring & Case Study Navigation 1.2 The Schematic Design Phase & Multi-Discipline Workflow 1.3 Regulatory Framework: Navigating Codes, Standards & Jurisdictions
2 Chapter 2: Site Analysis, Topography & Soil Conditions
2.1 Site Topography, Grading, Slopes & Cut/Fill Calculations 2.2 Geotechnical Reports, Soil Classification & Foundation Selection 2.3 Site Hydrology, Drainage & Stormwater Management Neighborhood Context, Historic Settings & Site Integration
3 Chapter 3: Climate, Microclimate & Solar Design
3.1 Solar Geometry, Sun Angles & Sun Path Diagrams 3.2 Microclimate Analysis, Prevailing Winds & Passive Ventilation 3.3 Passive Solar Heating & Thermal Mass Strategies
4 Chapter 4: Sustainable Principles & Energy Standards
4.1 Daylighting Metrics: Spatial Daylight Autonomy (sDA) & Annual Sun Exposure (ASE) 4.2 Building Energy Standards: ASHRAE 90.1, IECC & Energy Use Intensity (EUI) 4.3 High-Performance Frameworks: LEED v4.1, Net Zero & Embodied Carbon
5 Chapter 5: Zoning Regulations & Land Use Controls
5.1 Zoning Envelopes: Setbacks, Floor Area Ratio (FAR) & Lot Coverage 5.2 Parking Requirements, Access & Site Circulation Planning 5.3 Environmental Regulations: Wetlands, Flood Zones & Brownfields
6 Chapter 6: Building Code Fundamentals: Occupancy & Construction Types
6.1 IBC Occupancy Classifications & Group Characteristics 6.2 Mixed Occupancy Strategies: Nonseparated, Separated & Accessory 6.3 IBC Construction Types I Through V & Fire-Resistance Ratings 6.4 Allowable Building Height & Area Calculations (IBC Tables 504 & 506)
7 Chapter 7: Means of Egress & Fire Protection
7.1 Occupant Load Determination & Egress Sizing (IBC Chapter 10) 7.2 Egress Components: Common Path, Travel Distance & Exit Separation 7.3 Passive Fire Protection: Fire Walls, Barriers & Smoke Partitions 7.4 Active Fire Suppression: Sprinklers, Standpipes & Fire Alarms
8 Chapter 8: Accessibility & Universal Design
8.1 Accessible Routes, Curb Ramps & Parking Layouts (ADA / ICC A117.1) 8.2 Interior Accessibility: Doors, Maneuvering Clearances & Corridors 8.3 Accessible Plumbing Facilities: Restrooms, Grab Bars & Fixture Layouts
9 Chapter 9: Structural Systems: Wood, Steel, Concrete & Masonry
9.1 Structural Selection & Spanning Rules of Thumb 9.2 Steel Framing Systems: Beams, Girders & Open-Web Joists 9.3 Concrete Framing Systems: One-Way, Two-Way & Post-Tensioned Slabs 9.4 Wood Systems: Light-Frame, Heavy Timber & Mass Timber (CLT)
10 Chapter 10: Lateral Force Resisting Systems & Foundations
10.1 Lateral Load Paths: Wind vs. Seismic Forces 10.2 Shear Walls, Braced Frames & Moment Frames 10.3 Shallow vs. Deep Foundation Systems: Footings, Mats, Piles & Caissons
11 Chapter 11: Building Envelope: Physics, Assemblies & Moisture Control
11.1 Envelope Thermal Performance: U-Values, R-Values & Thermal Bridging 11.2 Moisture Management: Vapor Retarders, Air Barriers & Water Resistive Barriers 11.3 High-Performance Wall & Roof Assemblies: Rainscreens & Inverted Roofs 11.4 Fenestration & Glazing: U-Factor, SHGC, Condensation Resistance & VT Interior Materials, Durability & Program Performance
12 Chapter 12: Mechanical & HVAC Systems
12.1 HVAC System Types: All-Air, Air-Water, All-Water & VRF Systems 12.2 Central Plant Equipment: Chillers, Boilers, Cooling Towers & Geothermal 12.3 Ductwork Distribution, Air Handling & Plenum Space Requirements 12.4 Indoor Air Quality, Ventilation Rates & ASHRAE 62.1 Baselines
13 Chapter 13: Plumbing, Electrical & Life Safety Systems
13.1 Domestic Water Supply & Pressure Boosting Systems 13.2 Sanitary Drainage, Venting & Fixture Count Calculations 13.3 Electrical Service, Transformers, Switchgear & Backup Generators 13.4 Lighting Design, Controls & Lighting Power Density (LPD) Limits
14 Chapter 14: Specialized Building Systems & Vertical Circulation
14.1 Architectural Acoustics: STC, NRC, RT60 & Noise Criteria (NC) 14.2 Elevator Systems: Traction vs. Hydraulic, Core Layout & Sizing 14.3 Building Telecommunications, Security & Building Automation Systems (BAS)
15 Chapter 15: Systems Integration & Coordination
15.1 Floor-to-Floor Height & Plenum Coordination (Structure + MEP + Architecture) 15.2 Structural Grid Planning & Spatial Adjacencies 15.3 Building Massing, Orientation & Envelope Integration 15.4 Case Study Strategy: Synthesizing Drawings, Code Sheets & Schedules
16 Chapter 16: Project Costs, Budgeting & Life-Cycle Analysis
16.1 Schematic Estimating Techniques: Area, Volume & Parametric Costs 16.2 Project Budgets: Contingencies, Overhead, Profit & Escalation 16.3 Life-Cycle Cost Analysis (LCCA) & Value Engineering
13.1 Domestic Water Supply & Pressure Boosting Systems
Key Takeaways Explain This Topic AI
Use fixture-specific minimum operating pressures, residual supply pressure at design flow, elevation and friction losses; limit domestic static pressure under the applicable code.
Static elevation head decreases water pressure by 0.433 psi per vertical foot of rise (1 psi per 2.31 ft); building height directly determines whether municipal street pressure can supply fixtures via direct upfeed or if mechanical pressure boosting is required.
Calculate booster and pressure-zone boundaries from the required minimum and maximum pressures rather than assuming a fixed number of stories.
Backflow prevention isolates the potable water supply from contamination: physical air gaps provide the highest degree of protection for toxic cross-connections, Reduced Pressure Zone (RPZ) assemblies protect high-hazard mechanical and chemical loops, and Double Check Valve Assemblies (DCVA) serve low-hazard systems.
Last updated: October 2026
13.1 Domestic Water Supply & Pressure Boosting Systems
Designing a potable water distribution system requires balancing hydraulic delivery pressures, volumetric flow rates, spatial coordination, and water quality protection. Architects and mechanical engineers must ensure that water reaches every plumbing fixture with sufficient residual pressure to operate properly during peak simultaneous demand, while simultaneously preventing excessive hydrostatic pressure that damages piping, valves, and fixtures.
Hydraulic Fundamentals & Operating Pressure Limits
Water distribution systems operate under two distinct hydraulic states:
Static Pressure : The pressure exerted by water at rest, measured when no fixtures are open and no fluid is in motion. Static pressure is governed entirely by the supply source pressure and changes in vertical elevation.
Residual (Dynamic) Pressure : The pressure remaining in the piping system at a specific fixture outlet while water is actively flowing at design velocity. Residual pressure equals static pressure minus dynamic friction losses through piping, fittings, valves, water meters, and backflow preventers.
Fixture Pressure Thresholds
Every plumbing fixture requires a minimum residual operating pressure to function:
Use the actual IPC fixture category and manufacturer's minimum flow pressure. For example, the IPC lavatory value is 8 psi; a generic 20–25-psi minimum is not correct for all faucets. Mixing valves and flushometers can have different requirements. Use the design residual supply pressure to evaluate delivery.
Commercial Flushometer (Flush Valve) Water Closets : 35 to 40 psi 35\text{ to }40\text{ psi} 35 to 40 psi ( 241 to 276 kPa 241\text{ to }276\text{ kPa} 241 to 276 kPa ) minimum during active discharge. Flushometer valves require high instantaneous volumetric flow rates ( 25 to 35 GPM 25\text{ to }35\text{ GPM} 25 to 35 GPM ) for a brief 5-to-10 second burst, demanding robust residual pressure to actuate the internal diaphragm or piston.
Maximum Code Pressure & Pressure Reducing Valves (PRVs)
The International Plumbing Code (IPC Section 604.8) and the Uniform Plumbing Code (UPC Section 608.2) establish an absolute maximum static distribution pressure:
Maximum Allowable Static Pressure = 80 psi ( 552 kPa ) \text{Maximum Allowable Static Pressure} = 80\text{ psi } (552\text{ kPa}) Maximum Allowable Static Pressure = 80 psi ( 552 kPa )
Where municipal street pressure or booster pump discharge exceeds 80 psi 80\text{ psi} 80 psi , an approved Pressure Reducing Valve (PRV) equipped with an integral strainer must be installed on the supply service. Static pressures exceeding 80 psi 80\text{ psi} 80 psi cause severe hydraulic problems:
Water Hammer : Violent pressure shockwaves generated when fast-acting solenoid valves or flushometers snap shut, causing pipe vibrations that rupture solder joints and pipe hangers.
Erosion-Corrosion : Water velocity in domestic copper piping must be restricted to ≤ 8.0 ft/s \le 8.0\text{ ft/s} ≤ 8.0 ft/s ( 2.4 m/s 2.4\text{ m/s} 2.4 m/s ) for cold water and ≤ 5.0 ft/s \le 5.0\text{ ft/s} ≤ 5.0 ft/s ( 1.5 m/s 1.5\text{ m/s} 1.5 m/s ) for hot water ( > 140 ∘ F >140^\circ\text{F} > 14 0 ∘ F ). High pressure forces high velocities, stripping protective copper oxide films and causing pinhole leaks.
Appliance Damage : Rupture of flexible washing machine hoses, water heater relief valves, and premature diaphragm failure in flush valves.
Static Head & Dynamic Pressure Losses
Water is an incompressible fluid with a density of approximately 62.4 lbs/cu ft 62.4\text{ lbs/cu ft} 62.4 lbs/cu ft ( 8.34 lbs/gal 8.34\text{ lbs/gal} 8.34 lbs/gal ). A column of water exerts downward hydrostatic pressure proportional to its vertical height:
P static loss = 0.4332 psi per vertical foot of elevation ( 1 psi = 2.307 ft of water head ) P_{\text{static loss}} = 0.4332\text{ psi per vertical foot of elevation} \quad \left(1\text{ psi} = 2.307\text{ ft of water head}\right) P static loss = 0.4332 psi per vertical foot of elevation ( 1 psi = 2.307 ft of water head )
Every vertical rise in a building incurs an inescapable static pressure penalty. A 100 -foot 100\text{-foot} 100 -foot vertical climb drops water pressure by 43.3 psi 43.3\text{ psi} 43.3 psi before considering any pipe friction.
Dynamic Friction & Component Losses
As water travels through distribution piping, boundary layer shear stress creates dynamic friction loss, governed by the Hazen-Williams formula. Designers convert fittings (elbows, tees, gate valves) into "equivalent lengths" of straight pipe. In addition, discrete plumbing components impose concentrated pressure drops:
Municipal Water Meter : 5 to 15 psi 5\text{ to }15\text{ psi} 5 to 15 psi drop depending on flow rate and meter type (disc, turbine, compound).
Backflow Prevention Assembly : 8 to 12 psi 8\text{ to }12\text{ psi} 8 to 12 psi drop across internal check valves and springs in a Reduced Pressure Zone (RPZ) assembly.
Distribution Piping & Fittings : Typically budgeted at 3 to 5 psi per 100 ft 3\text{ to }5\text{ psi per } 100\text{ ft} 3 to 5 psi per 100 ft of equivalent pipe run.
Potable Water Distribution System Typologies
Building height and incoming municipal water pressure dictate the appropriate water distribution typology. +-----------------------------------------------------------------------------------------+
- | WATER DISTRIBUTION TYPOLOGIES |
- +-----------------------+-----------------------------+-----------------------------------+
- | System Typology | Application & Height Limit | Advantages & Spatial Liabilities |
- +-----------------------+-----------------------------+-----------------------------------+
- | Direct Municipal | Low-rise: 1 to 4 stories | Low capital cost; zero pumping |
- | Upfeed System | (40 to 60 ft max rise) | energy; subject to street main |
- | | | pressure fluctuations. |
- +-----------------------+-----------------------------+-----------------------------------+
- | Downfeed Gravity Tank | High-rise & mid-rise | Constant reliable pressure; built-|
- | System (Roof Tank) | (Any height, multi-tiered) | in 24-48 hr emergency reserve; |
- | | | heavy roof dead load; freeze risk.|
- +-----------------------+-----------------------------+-----------------------------------+
- | VFD Multi-Pump | Mid-rise to high-rise | Compact basement footprint; no |
- | Booster Package | (120 to 500+ ft) | heavy roof tanks; dynamic energy |
- | | | modulation; requires backup power.|
- +-----------------------+-----------------------------+-----------------------------------+
- 1. Direct Municipal Upfeed System
In a direct upfeed system, municipal main pressure drives water directly through the water meter, backflow preventer, and vertical distribution risers to all fixtures without mechanical pumps.
Maximum Practical Rise : Municipal street mains typically operate at 45 to 65 psi 45\text{ to }65\text{ psi} 45 to 65 psi . Accounting for a 10 psi 10\text{ psi} 10 psi meter loss, 10 psi 10\text{ psi} 10 psi RPZ loss, 10 psi 10\text{ psi} 10 psi pipe friction, and 20 to 35 psi 20\text{ to }35\text{ psi} 20 to 35 psi residual fixture pressure, available head for elevation is often only 15 to 25 psi 15\text{ to }25\text{ psi} 15 to 25 psi .
This limits direct upfeed systems to approximately 35 to 55 ft 35\text{ to }55\text{ ft} 35 to 55 ft ( 3 to 4 stories 3\text{ to }4\text{ stories} 3 to 4 stories ). Above this height, upper-floor fixtures experience flow starvation.
2. Downfeed / Gravity Tank System
A domestic water pump in the basement lifts water through a dedicated fill riser to an elevated rooftop storage tank. Water then feeds downward through distribution risers by gravity.
Pressure Characteristics : Static pressure increases as water moves downward ( 0.433 psi/ft 0.433\text{ psi/ft} 0.433 psi/ft ). At 80 ft 80\text{ ft} 80 ft below the tank, static pressure is 34.6 psi 34.6\text{ psi} 34.6 psi ; at 160 ft 160\text{ ft} 160 ft below the tank, static pressure reaches 69.3 psi 69.3\text{ psi} 69.3 psi .
Top-Floor Deficiency : The top two or three floors directly beneath the roof tank lack sufficient vertical drop to generate the 35 psi 35\text{ psi} 35 psi required for flushometer valves. These upper floors must be served by a small supplementary top-floor booster pump or utilize gravity flush-tank water closets.
Architectural Coordination : The roof tank imposes immense dead load on the structural frame ( 1 , 000 gallons = 8 , 340 lbs 1,000\text{ gallons} = 8,340\text{ lbs} 1 , 000 gallons = 8 , 340 lbs , excluding tank steel). In freezing climates, the tank must be insulated and provided with internal electric immersion heaters or steam coils.
3. Variable Frequency Drive (VFD) Booster Pump Packages
Modern commercial buildings favor skid-mounted booster pump packages equipped with Variable Frequency Drives (VFDs), superseding older hydropneumatic tanks. These skids typically combine two to four vertical multistage centrifugal pumps in parallel (duplex, triplex, or quadruplex configurations).
Operating Principle : Pressure transducers on the discharge header monitor downstream pressure in real time. Solid-state VFD controllers modulate pump motor rotational speed ( 0 to 60 Hz 0\text{ to }60\text{ Hz} 0 to 60 Hz ) to match instantaneous water consumption.
Staging & Redundancy : During low nighttime demand, a single small "jockey" or lead pump runs at low speed. As morning demand surges, secondary lag pumps stage on automatically. System sizing incorporates N + 1 N+1 N + 1 redundancy, ensuring full peak capacity even if one pump is offline for maintenance.
Spatial Advantages : Eliminates rooftop tank structural loads and penthouses. The compact equipment skid fits within a standard ground-floor or basement mechanical room.
4. Vertical Pressure Zoning in High-Rise Buildings
Because hydrostatic pressure increases by 43.3 psi per 100 ft 43.3\text{ psi per } 100\text{ ft} 43.3 psi per 100 ft of vertical descent, a tall building cannot be served by a single unzoned distribution riser without blowing out bottom-floor fixtures. If a 400 -foot 400\text{-foot} 400 -foot tower were fed from a single top-down gravity system, the ground floor would experience an intolerable static pressure of 173 psi 173\text{ psi} 173 psi .
Pressure-zone height is calculated from the allowed lower-floor maximum and upper-floor minimum, including friction. With an 80-psi maximum and a required 35-psi minimum, only 45 psi is available for elevation and friction: 45 / 0.433 ≈ 104 45/0.433≈104 45/0.433 ≈ 104 feet before friction. A universal 120–140-foot zone or 10–12-floor rule would not satisfy that assumed pressure window.
PRV Station Zoning : In booster pump or downfeed systems, PRV stations with parallel high-flow/low-flow regulator valves and bypass loops are located on intermediate mechanical floors to step down distribution pressure for lower zones.
Independent Pump Risers : Separate booster pump skids in the basement deliver water to dedicated vertical risers serving Low-Rise, Mid-Rise, and High-Rise zones independently.
Water Supply Fixture Units (WSFU) & Hunter's Curve
Plumbing supply pipes cannot be sized by simply adding together the maximum flow rates of all connected fixtures. In an office building with 100 flushometer toilets, the probability of all 100 flushing at the exact same second is statistically near zero.
In 1940, Dr. Roy B. Hunter of the National Bureau of Standards developed the Water Supply Fixture Unit (WSFU) methodology, a probability-based load calculation adopted by the IPC and UPC:
Water-supply fixture units are assigned under the selected code and sizing method. In IPC Appendix E, a public flushometer water closet and a private flush-tank water closet have different assigned loads; do not substitute drainage fixture units or assume all public/private fixture values are interchangeable. Convert the fixture-unit total using the appropriate demand method rather than adding every fixture's full flow.
Hunter's Curve (Peak Demand Conversion) : The engineer sums all WSFUs on a riser or main, then consults Hunter's Curve tables to convert cumulative WSFU into an anticipated Peak Design Flow Rate in Gallons Per Minute (GPM) . Hunter's Curve features two distinct curves: one for systems containing flushometer valves and one for systems utilizing flush tanks.
Total WSFU → Hunter’s Curve Peak Design Flow (GPM) → Velocity Limits ≤ 8 fps Pipe Diameter (Inches) \text{Total WSFU} \xrightarrow{\text{Hunter's Curve}} \text{Peak Design Flow (GPM)} \xrightarrow{\text{Velocity Limits } \le 8\text{ fps}} \text{Pipe Diameter (Inches)} Total WSFU Hunter’s Curve Peak Design Flow (GPM) Velocity Limits ≤ 8 fps Pipe Diameter (Inches)
Domestic Hot Water (DHW) Distribution & Recirculation
Energy conservation codes (ASHRAE Standard 90.1 and International Energy Conservation Code / IECC) mandate that public lavatories and showers receive hot water rapidly without wasting gallons down the drain while waiting for heated water to arrive.
Recirculation Loops
Where the distance from the hot water source to the furthest fixture exceeds 50 ft 50\text{ ft} 50 ft (or contains more than 0.5 gallons 0.5\text{ gallons} 0.5 gallons of water in the supply line per IECC Section C404.5), a continuous or demand-controlled DHW recirculation loop is required:
Loop Architecture : The hot water supply line runs past all fixtures and connects to a return line leading back to the water heater. A small fractional-horsepower circulator pump keeps tempered water ( 120 ∘ F 120^\circ\text{F} 12 0 ∘ F ) circulating constantly through the loop.
Balancing Valves : Calibrated balancing valves ensure even flow across multiple vertical risers.
Code Controls : IECC mandates that recirculation pumps be controlled by automatic timers, aquastats (turning off when return water reaches 110 ∘ F 110^\circ\text{F} 11 0 ∘ F ), or occupancy sensors, preventing continuous standby heat loss when the building is unoccupied.
Point-of-Use Instantaneous Heaters
For remote fixtures (such as an isolated security guardhouse or an executive restroom 200 ft 200\text{ ft} 200 ft from the central boiler plant), installing long insulated supply/return piping is inefficient. Point-of-use electric tankless water heaters installed directly beneath the sink provide instant hot water, eliminating recirculation loops and distribution thermal losses.
Cross-Connection Control & Backflow Prevention
A cross-connection is any physical link between a potable drinking water system and any non-potable liquid, gas, or chemical solution. Contamination occurs through two hydraulic mechanisms:
Backsiphonage : Negative or sub-atmospheric pressure in the supply main sucks non-potable liquids backward into the potable system (e.g., when a municipal water main breaks or fire department pumpers draw heavy suction from nearby fire hydrants).
Backpressure : Downstream pressure exceeds supply pressure, forcing contaminated fluids upstream (e.g., from a high-pressure hydronic heating boiler, cooling tower pump, or chemical injection line).
Backflow Prevention Assemblies
An air gap physically separates supply from the receiving vessel and protects against backsiphonage and backpressure when properly sized and located. An RPZ assembly protects qualifying high-hazard connections but needs drainage and accessible maintenance. A double-check assembly serves permitted lower-hazard applications. Vacuum breakers primarily address backsiphonage under their installation limitations. Hazard, pressure condition, device listing and adopted code determine the allowed selection; a generic hierarchy cannot replace those checks.
Air Gap : The most foolproof method of backflow prevention. An unobstructed vertical air space between the lowest opening of the supply pipe and the flood level rim of the fixture or receptor. Code mandates the air gap must be at least twice the effective diameter of the supply pipe , but never less than 1.0 inch 1.0\text{ inch} 1.0 inch ( 25 mm 25\text{ mm} 25 mm ).
Reduced Pressure Zone (RPZ) Assembly : Contains two independently acting spring-loaded check valves separated by a hydraulically operated differential pressure relief valve. If either check valve leaks or if supply pressure drops, the relief valve opens to atmosphere, discharging water onto the floor. Mandatory for high-hazard cross connections (HVAC cooling towers, hydronic chemical treatment, commercial laundry, laboratory feeds, irrigation with fertilizer injection).
Architectural Warning : RPZ valves must never be installed in a pit, sump, or vault subject to flooding, as submerging the relief port causes immediate cross-contamination. They must be installed in an above-ground mechanical room equipped with an air-gapped funnel drain sized to accept maximum relief discharge without flooding.
Double Check Valve Assembly (DCVA) : Consists of two independently acting check valves. Approved only for low-hazard (non-health) applications , such as standard wet-pipe fire sprinkler lines containing no antifreeze or toxic chemicals.
- Worked Calculation: Hydraulic Pressure Budget for a 6-Story Building
- Project Parameters
Building Type: 6-story commercial office building.
Elevation to critical fixture: Flushometer water closet on the 6th floor located 68 ft 68\text{ ft} 68 ft above the municipal water main.
Municipal supply pressure at street main: 58 psi 58\text{ psi} 58 psi static.
Total equivalent length of distribution piping (run + fittings): 220 ft 220\text{ ft} 220 ft .
Unit friction loss at peak design flow rate ( 120 GPM 120\text{ GPM} 120 GPM ): 4.0 psi per 100 ft 4.0\text{ psi per } 100\text{ ft} 4.0 psi per 100 ft .
Water meter pressure drop: 8.0 psi 8.0\text{ psi} 8.0 psi .
RPZ backflow preventer pressure drop: 10.0 psi 10.0\text{ psi} 10.0 psi .
Minimum residual operating pressure required at top flushometer: 35.0 psi 35.0\text{ psi} 35.0 psi .
Step-by-Step Pressure Evaluation
Calculate Static Head Loss : P static = 68 ft × 0.4332 psi/ft = 29.46 psi P_{\text{static}} = 68\text{ ft} \times 0.4332\text{ psi/ft} = 29.46\text{ psi} P static = 68 ft × 0.4332 psi/ft = 29.46 psi
Calculate Piping Friction Loss : P friction = ( 220 ft 100 ft ) × 4.0 psi = 8.80 psi P_{\text{friction}} = \left(\frac{220\text{ ft}}{100\text{ ft}}\right) \times 4.0\text{ psi} = 8.80\text{ psi} P friction = ( 100 ft 220 ft ) × 4.0 psi = 8.80 psi
Calculate Total System Pressure Demand : P total required = P static + P friction + P meter + P RPZ + P residual P_{\text{total required}} = P_{\text{static}} + P_{\text{friction}} + P_{\text{meter}} + P_{\text{RPZ}} + P_{\text{residual}} P total required = P static + P friction + P meter + P RPZ + P residual P total required = 29.46 psi + 8.80 psi + 8.00 psi + 10.00 psi + 35.00 psi = 91.26 psi P_{\text{total required}} = 29.46\text{ psi} + 8.80\text{ psi} + 8.00\text{ psi} + 10.00\text{ psi} + 35.00\text{ psi} = 91.26\text{ psi} P total required = 29.46 psi + 8.80 psi + 8.00 psi + 10.00 psi + 35.00 psi = 91.26 psi
Determine Pressure Deficit / Surplus : P available = 58.00 psi P_{\text{available}} = 58.00\text{ psi} P available = 58.00 psi Δ P = P available − P total required = 58.00 psi − 91.26 psi = − 33.26 psi \Delta P = P_{\text{available}} - P_{\text{total required}} = 58.00\text{ psi} - 91.26\text{ psi} = -33.26\text{ psi} Δ P = P available − P total required = 58.00 psi − 91.26 psi = − 33.26 psi
Engineering Resolution
The direct municipal pressure is deficient by 33.26 psi 33.26\text{ psi} 33.26 psi . At the 6th floor, available residual pressure without pumping would be only 1.74 psi 1.74\text{ psi} 1.74 psi , causing flushometer valves to fail completely. A triplex VFD booster pump system must be specified, engineered to deliver a minimum boost of 35 to 40 psi 35\text{ to }40\text{ psi} 35 to 40 psi at the design peak flow of 120 GPM 120\text{ GPM} 120 GPM (pump discharge setpoint ≈ 95 psi \approx 95\text{ psi} ≈ 95 psi ). Because the discharge pressure exceeds 80 psi 80\text{ psi} 80 psi , ground-floor and first-floor branches must be fitted with PRVs to protect lower fixtures from excessive pressure.