Study guide
2.2 Geotechnical Reports, Soil Classification & Foundation Selection
ARE 5.0 Project Planning & Design PPD
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview & Schematic Design Process
1.1 ARE 5.0 PPD Format, Scoring & Case Study Navigation 1.2 The Schematic Design Phase & Multi-Discipline Workflow 1.3 Regulatory Framework: Navigating Codes, Standards & Jurisdictions
2 Chapter 2: Site Analysis, Topography & Soil Conditions
2.1 Site Topography, Grading, Slopes & Cut/Fill Calculations 2.2 Geotechnical Reports, Soil Classification & Foundation Selection 2.3 Site Hydrology, Drainage & Stormwater Management Neighborhood Context, Historic Settings & Site Integration
3 Chapter 3: Climate, Microclimate & Solar Design
3.1 Solar Geometry, Sun Angles & Sun Path Diagrams 3.2 Microclimate Analysis, Prevailing Winds & Passive Ventilation 3.3 Passive Solar Heating & Thermal Mass Strategies
4 Chapter 4: Sustainable Principles & Energy Standards
4.1 Daylighting Metrics: Spatial Daylight Autonomy (sDA) & Annual Sun Exposure (ASE) 4.2 Building Energy Standards: ASHRAE 90.1, IECC & Energy Use Intensity (EUI) 4.3 High-Performance Frameworks: LEED v4.1, Net Zero & Embodied Carbon
5 Chapter 5: Zoning Regulations & Land Use Controls
5.1 Zoning Envelopes: Setbacks, Floor Area Ratio (FAR) & Lot Coverage 5.2 Parking Requirements, Access & Site Circulation Planning 5.3 Environmental Regulations: Wetlands, Flood Zones & Brownfields
6 Chapter 6: Building Code Fundamentals: Occupancy & Construction Types
6.1 IBC Occupancy Classifications & Group Characteristics 6.2 Mixed Occupancy Strategies: Nonseparated, Separated & Accessory 6.3 IBC Construction Types I Through V & Fire-Resistance Ratings 6.4 Allowable Building Height & Area Calculations (IBC Tables 504 & 506)
7 Chapter 7: Means of Egress & Fire Protection
7.1 Occupant Load Determination & Egress Sizing (IBC Chapter 10) 7.2 Egress Components: Common Path, Travel Distance & Exit Separation 7.3 Passive Fire Protection: Fire Walls, Barriers & Smoke Partitions 7.4 Active Fire Suppression: Sprinklers, Standpipes & Fire Alarms
8 Chapter 8: Accessibility & Universal Design
8.1 Accessible Routes, Curb Ramps & Parking Layouts (ADA / ICC A117.1) 8.2 Interior Accessibility: Doors, Maneuvering Clearances & Corridors 8.3 Accessible Plumbing Facilities: Restrooms, Grab Bars & Fixture Layouts
9 Chapter 9: Structural Systems: Wood, Steel, Concrete & Masonry
9.1 Structural Selection & Spanning Rules of Thumb 9.2 Steel Framing Systems: Beams, Girders & Open-Web Joists 9.3 Concrete Framing Systems: One-Way, Two-Way & Post-Tensioned Slabs 9.4 Wood Systems: Light-Frame, Heavy Timber & Mass Timber (CLT)
10 Chapter 10: Lateral Force Resisting Systems & Foundations
10.1 Lateral Load Paths: Wind vs. Seismic Forces 10.2 Shear Walls, Braced Frames & Moment Frames 10.3 Shallow vs. Deep Foundation Systems: Footings, Mats, Piles & Caissons
11 Chapter 11: Building Envelope: Physics, Assemblies & Moisture Control
11.1 Envelope Thermal Performance: U-Values, R-Values & Thermal Bridging 11.2 Moisture Management: Vapor Retarders, Air Barriers & Water Resistive Barriers 11.3 High-Performance Wall & Roof Assemblies: Rainscreens & Inverted Roofs 11.4 Fenestration & Glazing: U-Factor, SHGC, Condensation Resistance & VT Interior Materials, Durability & Program Performance
12 Chapter 12: Mechanical & HVAC Systems
12.1 HVAC System Types: All-Air, Air-Water, All-Water & VRF Systems 12.2 Central Plant Equipment: Chillers, Boilers, Cooling Towers & Geothermal 12.3 Ductwork Distribution, Air Handling & Plenum Space Requirements 12.4 Indoor Air Quality, Ventilation Rates & ASHRAE 62.1 Baselines
13 Chapter 13: Plumbing, Electrical & Life Safety Systems
13.1 Domestic Water Supply & Pressure Boosting Systems 13.2 Sanitary Drainage, Venting & Fixture Count Calculations 13.3 Electrical Service, Transformers, Switchgear & Backup Generators 13.4 Lighting Design, Controls & Lighting Power Density (LPD) Limits
14 Chapter 14: Specialized Building Systems & Vertical Circulation
14.1 Architectural Acoustics: STC, NRC, RT60 & Noise Criteria (NC) 14.2 Elevator Systems: Traction vs. Hydraulic, Core Layout & Sizing 14.3 Building Telecommunications, Security & Building Automation Systems (BAS)
15 Chapter 15: Systems Integration & Coordination
15.1 Floor-to-Floor Height & Plenum Coordination (Structure + MEP + Architecture) 15.2 Structural Grid Planning & Spatial Adjacencies 15.3 Building Massing, Orientation & Envelope Integration 15.4 Case Study Strategy: Synthesizing Drawings, Code Sheets & Schedules
16 Chapter 16: Project Costs, Budgeting & Life-Cycle Analysis
16.1 Schematic Estimating Techniques: Area, Volume & Parametric Costs 16.2 Project Budgets: Contingencies, Overhead, Profit & Escalation 16.3 Life-Cycle Cost Analysis (LCCA) & Value Engineering
2.2 Geotechnical Reports, Soil Classification & Foundation Selection
Key Takeaways Explain This Topic AI
SPT counts and soil classifications inform investigation but do not alone establish foundation capacity or settlement.
Check allowable bearing and total/differential settlement as separate geotechnical requirements.
Expansive-soil mitigation depends on measured behavior, moisture changes and the engineered foundation system.
Compare shallow, mat and deep foundations against loads, soil profile, groundwater, movement and cost.
Last updated: October 2026
Geotechnical Reports, Soil Classification & Foundation Selection
A building's structural integrity depends on the interaction between its foundation and the underlying earth. Geotechnical engineering reports provide the empirical subgrade data required by architects and structural engineers to establish safe bearing pressures, evaluate settlement risks, determine groundwater and frost line depths, and select appropriate foundation typologies.
Subsurface Investigations & Geotechnical Boring Logs
Subsurface exploration involves advancing exploratory soil borings across the building footprint to extract soil and rock core samples. The primary field test performed during borehole advancement is the Standard Penetration Test (SPT) (ASTM D1586).
The Standard Penetration Test & N-Values
During an SPT test:
A 140-pound (63.5 kg) hammer drops repeatedly from a height of 30 inches (760 mm) onto an anvil.
The hammer drives a 2.0-inch outside-diameter split-barrel sampler 18 inches into undisturbed subsoil in three consecutive 6-inch increments.
The N-value (Standard Penetration Resistance) is the sum of blow counts required to drive the sampler through the second and third 6-inch increments (the final 12 inches). The first 6-inch increment is discarded as seating drive.
The resulting N-value (blows/foot) can be empirically correlated with soil density, shear strength, and consistency:
SPT blow counts and soil descriptions are investigation data, not an automatic foundation selection table. Correct the measured count for the intended engineering correlation. Dense granular soils can often support shallow foundations, but settlement, groundwater and loading still control. High counts or refusal in gravel may reflect cobbles rather than continuous bedrock. Clay settlement requires appropriate strength and consolidation testing; an N-value alone does not establish negligible long-term settlement.
Groundwater Table & Frost Line Depth
Geotechnical logs record the Seasonal High Water Table (SHWT) using piezometers. High water tables introduce buoyant uplift forces ( F buoyant = γ w × V submerged F_{\text{buoyant}} = \gamma_w \times V_{\text{submerged}} F buoyant = γ w × V submerged , where γ w = 62.4 lb/ft 3 \gamma_w = 62.4\text{ lb/ft}^3 γ w = 62.4 lb/ft 3 ), requiring hydrostatic waterproofing, sub-slab pressure relief drains, or rock tie-down anchors.
Under IBC Section 1809.5, shallow exterior footings must extend below the established local frost line depth (ranging from 0 inches in southern coastal regions to 48–72 inches in northern zones). Bearing footings above the frost line exposes structures to frost heave —the upward mechanical thrust caused by expanding ice lenses forming in frozen soil pores.
Soil Classification & Bearing Capacities
The Unified Soil Classification System (USCS) (ASTM D2487) categorizes soils into coarse-grained, fine-grained, and highly organic groups based on grain size distribution (sieve analysis) and plasticity (Atterberg limits):
Coarse-Grained Soils (>50% retained on No. 200 sieve [0.075 mm]):
Gravels (G) : Well-graded gravel ( G W GW G W ), poorly graded gravel ( G P GP GP ), silty gravel ( G M GM GM ), clayey gravel ( G C GC GC ).
Sands (S) : Well-graded sand ( S W SW S W ), poorly graded sand ( S P SP SP ), silty sand ( S M SM SM ), clayey sand ( S C SC SC ).
Fine-Grained Soils (>50% passing No. 200 sieve):
Silts (M) : Inorganic silts with low plasticity ( M L ML M L ) or high plasticity ( M H MH M H , elastic silts).
Clays (C) : Inorganic lean clays ( C L CL C L , low plasticity) or fat clays ( C H CH C H , high plasticity).
Organic Soils (O & Pt) : Organic silts/clays ( O L OL O L , O H OH O H ) and Peat ( P t Pt Pt ). Highly compressible, decomposing organic matter; structurally incompetent and unsuited for foundation bearing.
IBC Presumptive Load-Bearing Values
Where comprehensive laboratory testing is not mandated, IBC 2021 Table 1806.2 establishes conservative presumptive allowable foundation pressure limits:
- Class of Materials Allowable Soil Bearing Capacity Lateral Bearing (psf/ft below grade)
- 1. Crystalline Bedrock 12,000 psf 1,200 psf/ft
- 2. Sedimentary & Foliated Rock 4,000 psf 400 psf/ft
- 3. Sandy Gravel & Gravel (GW, GP) 3,000 psf 200 psf/ft
- 4. Sand, Silty Sand, Clayey Sand (SW, SP, SM, SC) 2,000 psf 150 psf/ft
- 5. Clay, Sandy Clay, Silty Clay (CL, ML, MH, CH) 1,500 psf 100 psf/ft
- Expansive Soils & Plasticity Index
Expansive soils contain clay minerals belonging to the smectite/montmorillonite group that expand upon hydration and shrink upon desiccation, generating vertical swelling pressures exceeding 10,000 psf. Swell potential is evaluated using Atterberg Limits :
Liquid Limit (LL) : Moisture percentage at which soil transitions from plastic to liquid behavior.
Plastic Limit (PL) : Moisture percentage at which soil transitions from semi-solid to plastic behavior.
Plasticity Index (PI) : P I = L L − P L PI = LL - PL P I = LL − P L .
Plasticity index helps characterize fine-grained soils, but expansion also depends on mineralogy, moisture change, density and stress. PI bands are screening correlations, not universal code boundaries. Use geotechnical swell/consolidation tests to select and detail mitigation.
Structural Mitigation Strategies
Over-Excavation & Engineered Fill : Excavating 3 to 6 feet of expansive clay below footings and replacing it with non-expansive, select granular structural fill compacted in controlled lifts.
Post-Tensioned (PT) Slab-on-Grade : A stiffened concrete mat reinforced with orthogonal post-tensioned steel tendons. Thickened grade beams form a rigid structural raft that resists bending moments as soils heave or shrink beneath slab edges.
Deep Drilled Piers & Grade Beams with Void Forms : Supporting the superstructure on drilled concrete shafts anchored into stable bedrock or subsoils below the active moisture zone. Concrete grade beams connect pier tops above grade. To protect beams from upward heave, collapsible carton void forms (honeycomb corrugated cardboard boxes) are placed beneath beams during concrete placement. The forms degrade from soil moisture, leaving a 2-to-4-inch physical air gap that permits native soil expansion without transmitting upward uplift forces to the building frame.
Settlement Mechanics: Uniform vs. Differential
When structural column and wall loads are applied to subsoils, vertical settlement occurs:
Uniform Settlement : All columns, walls, and footings settle by an equal vertical distance. Because the building moves as a monolithic unit, structural members experience negligible secondary bending or shear stresses. The principal risks involve damage to rigid utility lines (gas, sanitary sewer, water) entering foundation walls and doorstep elevation misalignments.
Angular distortion compares differential settlement with support spacing. Acceptable movement depends on the structure, finishes, equipment and utilities. Establish project tolerances with the engineers rather than treating 1/500 or another heuristic as a universal onset of damage or code failure.
Foundation Selection: Shallow vs. Deep Systems
Foundation systems are classified into shallow and deep typologies based on the ratio of foundation embedment depth ( D D D ) to footing width ( B B B ):
Shallow Foundations ( D / B ≤ 1 D / B \le 1 D / B ≤ 1 )
Isolated Spread Footings (Pad Footings) : Square or rectangular reinforced concrete pads supporting individual columns. Most economical when allowable soil bearing capacity is ≥ 2 , 500 − 3 , 000 psf \ge 2,500 - 3,000\text{ psf} ≥ 2 , 500 − 3 , 000 psf and groundwater is below the footing excavation.
Strip Footings (Continuous Wall Footings) : Continuous linear concrete footings supporting load-bearing CMU, concrete, or light-gauge steel walls.
Mat (Raft) Foundations : A continuous, heavily reinforced concrete slab spanning under the entire building footprint. Selected when column loads are heavy, soil bearing capacity is low ( 1 , 500 − 2 , 000 psf 1,500 - 2,000\text{ psf} 1 , 500 − 2 , 000 psf ), or individual spread footings would cover more than 50% of the building footprint. The mat acts as a monolithic diaphragm, bridging localized soft soil pockets and reducing differential-settlement risk.
Deep Foundations ( D / B ≫ 1 D / B \gg 1 D / B ≫ 1 )
Driven Piles : Slender structural columns of steel (H-piles), precast concrete, or steel pipe piles driven into the earth by drop hammers. They support loads through end-bearing on competent bedrock or skin friction along the soil-pile interface.
Drilled Shafts (Caissons) : Large-diameter (2.5 to 10+ feet) cylindrical shafts excavated with rotary augers down to competent bedrock or hardpan, reinforced with full-length steel cages, and filled with concrete. Drilled caissons support column loads exceeding 1,000 to 5,000+ kips per shaft.
Micropiles (Minipiles) : Small-diameter (3 to 10 inches) high-capacity drilled and pressure-grouted piles containing a high-strength central threaded steel bar. Ideal for underpinning existing settling foundations, seismic retrofits, and tight urban infill sites with restricted vertical drill clearance.