Study guide
10.4 Proximal Femur Positioning: Neck Rotation, Shaft Placement, and Positioning Aids
ARRT Bone Densitometry Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation & the ARRT Blueprint
1.1 About the ARRT Bone Densitometry Examination 1.2 Eligibility, Structured Education, and Clinical Experience
2 Chapter 2: Osteoporosis, Bone Biology & Risk Factors
2.1 Osteoporosis: Definitions, Types, and WHO Diagnostic Criteria 2.2 Bone Functions, Structural Anatomy, and Bone Types 2.3 Bone Cells, the Remodeling Cycle, and Calcium Homeostasis 2.4 Risk Factors, Secondary Causes, and Bone-Compromising Medications
3 Chapter 3: Indications, Prevention & Treatment
3.1 The Bone Mass Measurement Act: Covered Indications and Coding 3.2 Prevention: Nutrition, Exercise, Smoking Cessation, and Fall Prevention 3.3 Osteoporosis Drug Therapy: Antiresorptive, Anabolic, and Hormonal Agents
4 Chapter 4: Patient Preparation, Support & Radiation Safety
4.1 Patient Support, Disabilities, Ergonomics, and Transfer Techniques 4.2 Patient Instructions: Explaining the Exam, Dose, Duration, and Motion Control 4.3 Patient History, Contraindications, and Pregnancy Screening 4.4 Scan Preparation: Patient Data Entry, Artifact Removal, and Infection Control 4.5 Radiation Safety in DXA: ALARA, Distance, and Dose Levels
5 Chapter 5: DXA Physics & Instrumentation
5.1 Physical Principles of Dual-Energy X-ray Absorptiometry 5.2 Beam Geometries: Pencil Beam and Fan Beam Systems 5.3 Fan-Beam Geometry: Source–Object–Detector Distances, Magnification, and Centering 5.4 The Scan Analysis Algorithm: Soft Tissue, Bone Edge Detection, BMC, Area, and BMD
6 Chapter 6: Measuring & Reporting Bone Mineral Density
6.1 Statistics for Densitometry: Mean, Standard Deviation, and Coefficient of Variation 6.2 T-Scores, Z-Scores, and Reference Database Selection 6.3 Clinical Indications for BMD Testing and the FRAX Tool 6.4 Vertebral Fracture Assessment and Trabecular Bone Score 6.5 Whole Body DXA, Body Composition, and Pediatric Scanning
7 Chapter 7: Quality Control, Precision & Equipment Management
7.1 Accuracy, Precision, and the Sources of Precision Error 7.2 Daily Quality Control, Phantoms, and Control Charts 7.3 In Vivo Precision Studies and RMS-SD Calculation 7.4 Determining and Applying the Least Significant Change 7.5 Maintenance, Repair, Relocation, Cross-Calibration, and Software Upgrades
8 Chapter 8: DXA Informatics & Data Management
8.1 DXA Informatics, DICOM, PACS, and Data Management
9 Chapter 9: Lumbar Spine DXA
9.1 Lumbar Spine Anatomy, Landmarks, and Regions of Interest 9.2 Lumbar Spine Scan Acquisition and ROI Edge Placement 9.3 Lumbar Spine: Compensating for Body Habitus, Variant Anatomy, Pathology, and Low Bone Density 9.4 Lumbar Spine Positioning: The Leg Block, Centering, and Common Challenges 9.5 Lumbar Spine Problems: Poor Bone Edge Detection and Obscured Intervertebral Spaces 9.6 Lumbar Spine: Variant Anatomy, Fractures, Degenerative Pathology, Calcification, and Surgery 9.7 Lumbar Spine Analysis: Vertebral Exclusion and Reporting Rules 9.8 Lumbar Spine Follow-Up Scans and Rate of Change
10 Chapter 10: Proximal Femur DXA
10.1 Proximal Femur Anatomy, Landmarks, and Regions of Interest 10.2 Femur Selection: Right, Left, and Dual Femur Scanning 10.3 Proximal Femur Scan Parameters and Compensation 10.4 Proximal Femur Positioning: Neck Rotation, Shaft Placement, and Positioning Aids 10.5 Proximal Femur Problems: Ischium, Short Neck, Arthritis, Fracture, and Hardware 10.6 Femoral ROI Analysis: Femoral Neck, Total Hip, and Ward's Area 10.7 Proximal Femur Follow-Up Scans and Rate of Change
11 Chapter 11: Forearm DXA
11.1 Forearm Anatomy, Landmarks, and Adjacent Structures 11.2 Forearm Indications and Side Selection 11.3 Forearm Length Measurement, Scan Parameters, and Positioning 11.4 Forearm Regions of Interest: One-Third, Mid, Ultradistal, and Total 11.5 Forearm Problems: Edge Detection, Artifacts, Low Bone Density, and Joint Disease 11.6 Scan Analysis: Region Placement, Window Level, and Reported Values 11.7 Forearm Follow-Up Scans and Rate of Change
12 Chapter 12: Cross-Site Artifacts & Clinical Integration
12.1 Recognition, Impact, and Management of DXA Artifacts 12.2 Clinical Interpretation, Serial Comparison, and Reporting
10.4 Proximal Femur Positioning: Neck Rotation, Shaft Placement, and Positioning Aids
Key Takeaways Explain This Topic AI
The femoral neck is naturally anteverted, so internal rotation of approximately 15 to 25 degrees brings the neck axis parallel to the tabletop and into true profile.
A small or barely visible lesser trochanter indicates adequate internal rotation, while a large prominent lesser trochanter indicates insufficient rotation.
Insufficient internal rotation foreshortens the projected femoral neck, reducing area and falsely elevating the measured femoral neck BMD.
The femoral shaft must be straight and parallel to the long axis of the scan table, because the software derives the neck box orientation from the shaft axis.
The hip positioner or foot brace standardizes rotation between visits, and the same aid at the same setting must be used at follow-up.
Last updated: September 2026
10.4 Proximal Femur Positioning: Neck Rotation, Shaft Placement, and Positioning Aids
Quick Answer: Internally rotate the leg 15–25 degrees with a hip positioner so the anteverted femoral neck lies parallel to the tabletop and projects in true profile. Keep the femoral shaft straight and parallel to the table long axis . Read rotation from the lesser trochanter : small or barely visible = correct ; large and prominent = under-rotated . Under-rotation foreshortens the neck, shrinks projected area, and falsely elevates femoral neck BMD.
Femoral Neck Rotation: The Anatomy Behind the Rule
The femoral neck does not lie in the coronal plane. It projects anteriorly from the shaft at an angle of roughly 10 to 20 degrees — femoral anteversion . With the leg in neutral or externally rotated position, the neck is oblique to the tabletop, so a posteroanterior projection sees it at an angle and records a foreshortened image.
Internally rotating the whole lower extremity rotates the anteverted neck back into the plane of the table. When rotation is correct:
The femoral neck appears at its longest projected length .
The neck is displayed in true profile , with the head, neck, and trochanteric region clearly separated.
The lesser trochanter — which projects posteromedially — rotates behind the shaft and becomes small or nearly invisible.
Reading Rotation from the Lesser Trochanter
This is the highest-yield image-evaluation skill in femur scanning.
- Lesser trochanter appearance Rotation state Effect on measurement
- Not visible or barely visible Adequate internal rotation Neck at full projected length; correct
- Small, partially visible Acceptable, near optimal Generally acceptable
Large and prominent Insufficient internal rotation (neutral or externally rotated) Neck foreshortened ; area reduced; BMD falsely elevated
Completely absent with neck appearing unusually short and the greater trochanter projecting oddly Over-rotation (excessive internal rotation) Neck geometry distorted; unreliable
Why Under-Rotation Raises BMD
Foreshortening compresses the projected femoral neck along its long axis. The same mineral now occupies a smaller projected area: BMD = BMC Area ↑ when Area ↓ \text{BMD} = \frac{\text{BMC}}{\text{Area}} \uparrow \text{ when Area } \downarrow BMD = Area BMC ↑ when Area ↓
The bone has not changed. A patient scanned with a prominent lesser trochanter at baseline and correctly rotated at follow-up will appear to have lost bone, and the reverse produces an apparent gain. This is one of the largest single positioning errors in densitometry, which is why rotation is standardized with an aid rather than eyeballed.
Positioning Aids
The hip positioner — variously called a foot brace, femur positioner, or rotation device — is a manufacturer-supplied wedge or V-shaped brace that the foot and ankle strap into.
It standardizes the rotation angle rather than relying on the patient maintaining a voluntary position.
It holds the position for the full acquisition, preventing the slow external drift that occurs when a relaxed patient's leg rolls outward.
It has settings or markings ; record which was used, and use the same one at follow-up.
Without an aid, patients relax and the leg externally rotates during the scan, so the rotation at the end of the acquisition differs from the rotation at the start.
The Standard Position, Step by Step
Patient supine and centered on the table, midline aligned.
Confirm the side. Check for prior hip surgery, prosthesis, fracture, or hardware. A replaced hip is unmeasurable; scan the other side.
Leg straight and shaft parallel to the table long axis. The femur should run straight along the table, neither abducted nor adducted. Abduction or adduction changes the shaft angle and therefore the neck box orientation.
Internally rotate the whole lower extremity — rotating from the hip, not by twisting the foot against a fixed knee. The patella should rotate toward the midline with the rest of the leg.
Secure the foot in the hip positioner and strap it. Verify the ankle is comfortable; a painful position will be abandoned by the patient mid-scan.
Contralateral leg positioned per the manufacturer's instruction, typically straight and out of the scan field, or elevated on a support for dual-femur protocols.
Arms placed across the chest or at the sides, clear of the scan field.
Set the scan field to include shaft below the lesser trochanter, the full greater trochanter, the ischium, and lateral soft tissue.
Acquire , then evaluate before the patient leaves : lesser trochanter appearance, shaft alignment, field coverage, motion.
What a Correctly Positioned Femur Looks Like
- Criterion Correct appearance
- Lesser trochanter Small or barely visible
- Femoral shaft Straight and parallel to the image long axis
- Femoral neck At maximum projected length, in true profile
- Shaft position in field Centered, with adequate soft tissue on both sides
- Field coverage Shaft below lesser trochanter through the full greater trochanter
- Ischium Visible but ideally not overlying the femoral neck
- Common Challenges
- Arthritis and Limited Range of Motion
Severe hip osteoarthritis, previous fracture, contracture, and pain all limit internal rotation.
Rotate to the maximum tolerated angle , not the theoretical one.
Document the achieved rotation: "internal rotation limited to approximately 10 degrees by hip pain; lesser trochanter prominent."
Reproduce it at follow-up. A consistently under-rotated femur scanned identically each time still gives a valid serial comparison , even though the absolute value is biased. Consistency is worth more than an unachievable ideal.
Consider the contralateral hip if it rotates better — but once chosen, that side is the side forever.
Obesity
Large thigh and gluteal soft tissue resists rotation and obscures landmarks.
Verify the shaft is genuinely parallel rather than appearing so under soft tissue.
Use a slower acquisition mode.
Contracture and Neurologic Conditions
Flexion contracture prevents the leg from lying flat; support the knee and document.
Spasticity may make the position unattainable; a shortened protocol or an alternative site may be more useful than repeated attempts.
Leg Length Discrepancy and Pelvic Obliquity
The pelvis may not lie flat, changing the projected relationship between the ischium and the femoral neck.
Level the pelvis with radiolucent support where possible and document.
The Precision Payoff
Femoral neck precision is the poorest of the three central regions, and rotation variability is the main reason. ISCD's minimum acceptable precision is 2.5% for the femoral neck versus 1.8% for the total hip , and the difference is almost entirely positioning and ROI placement. Standardizing rotation with an aid, checking the lesser trochanter on every image, and reproducing the documented position at follow-up is how a technologist brings femoral neck precision into range.