Study guide
10.3 Proximal Femur Scan Parameters and Compensation
ARRT Bone Densitometry Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation & the ARRT Blueprint
1.1 About the ARRT Bone Densitometry Examination 1.2 Eligibility, Structured Education, and Clinical Experience
2 Chapter 2: Osteoporosis, Bone Biology & Risk Factors
2.1 Osteoporosis: Definitions, Types, and WHO Diagnostic Criteria 2.2 Bone Functions, Structural Anatomy, and Bone Types 2.3 Bone Cells, the Remodeling Cycle, and Calcium Homeostasis 2.4 Risk Factors, Secondary Causes, and Bone-Compromising Medications
3 Chapter 3: Indications, Prevention & Treatment
3.1 The Bone Mass Measurement Act: Covered Indications and Coding 3.2 Prevention: Nutrition, Exercise, Smoking Cessation, and Fall Prevention 3.3 Osteoporosis Drug Therapy: Antiresorptive, Anabolic, and Hormonal Agents
4 Chapter 4: Patient Preparation, Support & Radiation Safety
4.1 Patient Support, Disabilities, Ergonomics, and Transfer Techniques 4.2 Patient Instructions: Explaining the Exam, Dose, Duration, and Motion Control 4.3 Patient History, Contraindications, and Pregnancy Screening 4.4 Scan Preparation: Patient Data Entry, Artifact Removal, and Infection Control 4.5 Radiation Safety in DXA: ALARA, Distance, and Dose Levels
5 Chapter 5: DXA Physics & Instrumentation
5.1 Physical Principles of Dual-Energy X-ray Absorptiometry 5.2 Beam Geometries: Pencil Beam and Fan Beam Systems 5.3 Fan-Beam Geometry: Source–Object–Detector Distances, Magnification, and Centering 5.4 The Scan Analysis Algorithm: Soft Tissue, Bone Edge Detection, BMC, Area, and BMD
6 Chapter 6: Measuring & Reporting Bone Mineral Density
6.1 Statistics for Densitometry: Mean, Standard Deviation, and Coefficient of Variation 6.2 T-Scores, Z-Scores, and Reference Database Selection 6.3 Clinical Indications for BMD Testing and the FRAX Tool 6.4 Vertebral Fracture Assessment and Trabecular Bone Score 6.5 Whole Body DXA, Body Composition, and Pediatric Scanning
7 Chapter 7: Quality Control, Precision & Equipment Management
7.1 Accuracy, Precision, and the Sources of Precision Error 7.2 Daily Quality Control, Phantoms, and Control Charts 7.3 In Vivo Precision Studies and RMS-SD Calculation 7.4 Determining and Applying the Least Significant Change 7.5 Maintenance, Repair, Relocation, Cross-Calibration, and Software Upgrades
8 Chapter 8: DXA Informatics & Data Management
8.1 DXA Informatics, DICOM, PACS, and Data Management
9 Chapter 9: Lumbar Spine DXA
9.1 Lumbar Spine Anatomy, Landmarks, and Regions of Interest 9.2 Lumbar Spine Scan Acquisition and ROI Edge Placement 9.3 Lumbar Spine: Compensating for Body Habitus, Variant Anatomy, Pathology, and Low Bone Density 9.4 Lumbar Spine Positioning: The Leg Block, Centering, and Common Challenges 9.5 Lumbar Spine Problems: Poor Bone Edge Detection and Obscured Intervertebral Spaces 9.6 Lumbar Spine: Variant Anatomy, Fractures, Degenerative Pathology, Calcification, and Surgery 9.7 Lumbar Spine Analysis: Vertebral Exclusion and Reporting Rules 9.8 Lumbar Spine Follow-Up Scans and Rate of Change
10 Chapter 10: Proximal Femur DXA
10.1 Proximal Femur Anatomy, Landmarks, and Regions of Interest 10.2 Femur Selection: Right, Left, and Dual Femur Scanning 10.3 Proximal Femur Scan Parameters and Compensation 10.4 Proximal Femur Positioning: Neck Rotation, Shaft Placement, and Positioning Aids 10.5 Proximal Femur Problems: Ischium, Short Neck, Arthritis, Fracture, and Hardware 10.6 Femoral ROI Analysis: Femoral Neck, Total Hip, and Ward's Area 10.7 Proximal Femur Follow-Up Scans and Rate of Change
11 Chapter 11: Forearm DXA
11.1 Forearm Anatomy, Landmarks, and Adjacent Structures 11.2 Forearm Indications and Side Selection 11.3 Forearm Length Measurement, Scan Parameters, and Positioning 11.4 Forearm Regions of Interest: One-Third, Mid, Ultradistal, and Total 11.5 Forearm Problems: Edge Detection, Artifacts, Low Bone Density, and Joint Disease 11.6 Scan Analysis: Region Placement, Window Level, and Reported Values 11.7 Forearm Follow-Up Scans and Rate of Change
12 Chapter 12: Cross-Site Artifacts & Clinical Integration
12.1 Recognition, Impact, and Management of DXA Artifacts 12.2 Clinical Interpretation, Serial Comparison, and Reporting
10.3 Proximal Femur Scan Parameters and Compensation
Key Takeaways Explain This Topic AI
The femur scan field must include the femoral shaft distal to the lesser trochanter, the full femoral neck, the greater trochanter, and adjacent soft tissue for the baseline estimate.
Large patients require a slower acquisition mode for adequate photon statistics, because the hip is surrounded by more soft tissue than the lumbar spine.
Low bone density degrades the separation between the femoral neck and the overlying ischium, so the manufacturer's low-density analysis option and bone map review are essential.
Insufficient soft tissue between the ischium and the femur is a named cause of inaccurate values and cannot always be corrected by repositioning.
Any non-standard scan field, mode, or positioning must be documented so the identical acquisition can be reproduced at follow-up.
Last updated: September 2026
10.3 Proximal Femur Scan Parameters and Compensation
Quick Answer: A standard proximal femur acquisition includes the femoral shaft distal to the lesser trochanter , the entire femoral neck , the greater trochanter , and enough adjacent soft tissue for the baseline estimate. Compensation is needed for large habitus (slower mode), low bone density (low-density analysis, manual review), and variant anatomy or pathology (documented achievable positioning). The femur tolerates error less well than the spine because the neck ROI sits between the ischium and the greater trochanter.
The Standard Scan Field
Getting the field right is the first parameter decision, and it constrains everything downstream.
Boundary Requirement
Distal (inferior) Include femoral shaft well below the lesser trochanter ; the software uses shaft axis to orient the analysis
- Proximal (superior) Include the entire greater trochanter and the superior acetabular margin region
- Medial Include the ischium and sufficient soft tissue medial to the femoral neck
- Lateral Include soft tissue lateral to the greater trochanter for baseline estimation
A field cropped too tightly is the most common avoidable femur error. If the shaft is truncated, the software cannot establish the femoral axis and the neck box is placed at the wrong angle. If soft tissue is missing medially, the baseline estimate is unreliable in exactly the region where the neck ROI sits.
Standard Technique
Confirm site selection and side, and check for prior hip surgery on the intended side.
Position per the positioning protocol — supine, hip positioner, internal rotation — covered in the following section.
Set the scan field per the boundaries above, using the localizer.
Select the acquisition mode appropriate to the patient's habitus and bone density.
Instruct the patient: breathe quietly, remain still, do not move the foot.
Acquire, then review the image before releasing the patient — check rotation, field coverage, and motion.
Reviewing before the patient leaves the table is the single highest-value habit in femur scanning. A rotation error discovered at analysis, after the patient has dressed and gone, becomes either a bad measurement or a return visit.
Compensating for Body Habitus
The proximal femur lies deeper than the lumbar spine in most patients, surrounded by gluteal and thigh soft tissue that varies enormously.
Large habitus: select a slower mode . Insufficient photons produce a noisy image where the low-contrast boundary between the femoral neck and the overlying ischium becomes indistinguishable.
Soft tissue asymmetry: a large panniculus or asymmetric gluteal bulk distorts the baseline. Position symmetrically where possible and document.
Table and field limits: very large patients may exceed the table weight limit or the lateral field width. When both hip and spine are unmeasurable for this reason, the 33% radius is the accepted alternative site.
Very thin patients: less attenuation permits a faster mode, but verify there is adequate soft tissue in the baseline regions.
Compensating for Low Bone Density
The femoral neck in severe osteoporosis is a low-contrast structure sitting immediately over the ischium, which is itself bone. When neck density falls, the boundary between the two fades.
- Response Detail
- Use the low-density acquisition mode where supplied Better photon statistics at low contrast
- Use the low-density analysis option Adjusted edge-detection thresholds
- Inspect the bone map against the anatomy every time Auto-analysis is least reliable here
- Verify the neck box does not include ischium or greater trochanter The classic low-density failure
- Document mode, options, and any manual editing Reproducibility
- Compensating for Variant Anatomy
Short femoral neck. A short neck leaves little room between the femoral head and the greater trochanter, and the standard neck ROI box may not fit cleanly. The software's automatic placement may overlap adjacent structures; verify and adjust per the manufacturer's method, then reproduce it.
Inadequate space between the ischium and the femur. This is named explicitly in the ARRT outline. In some patients — particularly those with a wide pelvis, marked hip adduction, or limited internal rotation — the ischium projects directly under the femoral neck. It cannot always be corrected by positioning. Document it, and consider whether the contralateral hip is better.
Coxa vara or coxa valga. Altered neck-shaft angle changes the appearance and the relationship of the neck to the shaft axis. The software derives the neck angle from the shaft, so accurate shaft inclusion in the field matters more here.
Developmental dysplasia, prior slipped epiphysis, Perthes deformity. Distorted proximal femoral anatomy may make one hip unusable; use the other.
Compensating for Pathology
Severe osteoarthritis. Joint space narrowing, subchondral sclerosis, and osteophytes at the femoral head and acetabulum raise apparent BMD, particularly in the total hip region. Severe arthritis may also physically prevent internal rotation.
Prior fracture of the proximal femur. A healed or healing fracture, with or without hardware, invalidates that hip. Scan the contralateral side.
Hip arthroplasty. An implanted prosthesis makes that femur unmeasurable. Scan the other side; if both are replaced, the spine or forearm governs.
Paget disease of the femur. Markedly elevated and unreliable values; exclude the site.
Metastatic lesions. Lytic lesions lower and blastic lesions raise measured density; either invalidates the site.
Heterotopic ossification around the hip after surgery or trauma adds dense material within the field.
Documentation Requirements
For the femur specifically, record:
- Which side was scanned, and why if it was not the default
- Acquisition mode, and any low-density option used
- Achieved internal rotation if standard rotation could not be obtained
- Positioning aids used and their settings
- Any manual bone-map or ROI editing
- Non-removable artifacts and their location
- Any anatomical limitation such as ischium underlying the neck
At follow-up, all of it is reproduced. A femur scanned on the right at baseline and the left at follow-up produces a comparison that is meaningless regardless of how carefully each individual scan was performed.