Study guide
3.1 Virtual Switching Framework (VSF) Architecture and Topologies
HPE Aruba Networking Certified Associate - Campus Access HPE6-A85
Track your progress as you read
Finished sections get a check mark.
1 Introduction: HPE6-A85 Exam Overview
HPE6-A85 Exam Facts and Current Blueprint
2 Chapter 1: Network Stack Fundamentals
1.1 OSI Reference Model and Encapsulation 1.2 TCP/IP Protocol Suite and IP Headers 1.3 Layer 2 Operation, ARP, and 802.1Q Tagging
3 Chapter 2: Physical Connectivity and Host Addressing
2.1 Ethernet Media and Transceiver Standards 2.2 Power over Ethernet (PoE, PoE+, PoE++) Standards and Budgeting 2.3 LLDP, LLDP-MED, and Voice VLAN Configuration 2.4 Host IP Addressing and DHCP Relay Operations
4 Chapter 3: Network Resiliency and Virtualization
3.1 Virtual Switching Framework (VSF) Architecture and Topologies 3.2 VSF Split Detection, Failover, and Auto-Stacking 3.3 Virtual Switching Extension (VSX) Architecture and Operations 3.4 High-Availability Gateways: VRRP and VSX Active-Gateway
5 Chapter 4: AOS-CX Architecture and Switch Operation
4.1 AOS-CX Hardware Portfolio and State Database Architecture 4.2 Network Analytics Engine (NAE) and Automated Telemetry 4.3 AOS-CX Interface Configuration and Port Control 4.4 Link Aggregation (LAG) and LACP Configuration
6 Chapter 5: Layer 2 Protocols and Spanning Tree
5.1 AOS-CX VLAN Configuration and Native VLAN Handling 5.2 Spanning Tree Protocols: STP, RSTP, and MSTP 5.3 Spanning Tree Protections and Loop Prevention 5.4 MAC Address Table Learning, Aging, and Forwarding
7 Chapter 6: Wireless Fundamentals, Standards, and RF
6.1 IEEE 802.11 Standards and Wi-Fi Generations 6.2 RF Fundamentals, Signal Propagation, and Channel Design 6.3 Aruba Access Point Hardware Portfolio and Suffix Conventions 6.4 WLAN Topologies, BSSID/ESSID, and Roaming Standards
8 Chapter 7: Aruba Wireless Architecture and Management
7.1 AOS 10 Architecture and Aruba Central Integration 7.2 Wireless Forwarding Modes: Bridge vs Tunnel Mode 7.3 Automated RF and Client Optimization: AirMatch and ClientMatch 7.4 Secure Wireless Access: WPA3, SAE, and MPSK Implementation
9 Chapter 8: IP Routing Fundamentals and OSPF
8.1 IP Routing Principles and Packet Forwarding 8.2 OSPFv2 Protocol Mechanics and Adjacency Formation 8.3 OSPF Designated Routers and Multi-Area Deployments 8.4 ECMP, Static Routing, and VRF Isolation
10 Chapter 9: Campus Network Security and Segmentation
9.1 DHCP Snooping and Dynamic ARP Inspection 9.2 Port Security and MAC Address Limiting 9.3 ClearPass Policy Management and RADIUS Change of Authorization 9.4 Dynamic Segmentation, User-Based Tunneling, and Policy Enforcement
11 Chapter 10: Authentication, Authorization, and Accounting
10.1 The AAA Framework and Architecture 10.2 802.1X Authentication and EAP Methods 10.3 MAC Authentication and Captive Portal Onboarding 10.4 Administrative Access Control: RADIUS vs TACACS+
12 Chapter 11: Network Management and Telemetry
11.1 Aruba Central Cloud Architecture and Group Configuration 11.2 Zero-Touch Provisioning (ZTP) and Aruba Activate 11.3 AI Insights and Aruba User Experience Insight (UXI) 11.4 Network Telemetry, Streaming APIs, and SNMP/Syslog
13 Chapter 12: Troubleshooting the Solution
12.1 Structured Troubleshooting Methodologies and Scope Isolation 12.2 AOS-CX Layer 2 and Interface Diagnostic Commands 12.3 Layer 3, IP Services, and End-to-End Diagnostics 12.4 Physical-Layer Troubleshooting 12.5 Troubleshooting Wireless Clients and Network Access
14 Chapter 13: Optimizing Performance: QoS, Baselines, and Comparisons
13.1 Quality of Service (QoS) Classification and Marking 13.2 Queuing Algorithms and Congestion Management 13.3 Traffic Policing, Shaping, and Broadcast Rate Limiting 13.4 Establishing a Performance Baseline 13.5 Comparing Results to the Baseline
15 Chapter 14: Plan the Solution
14.1 Analyzing the Current Environment 14.2 Interpreting an Architect's High-Level Design 14.3 Creating a Low-Level Design 14.4 Preparing for Implementation
16 Chapter 15: Validate and Operate the Solution
15.1 Validating the Solution 15.2 Performing Firmware Updates 15.3 Making Basic Ongoing Configuration Changes 15.4 Maintaining Network Documentation
3.1 Virtual Switching Framework (VSF) Architecture and Topologies
Key Takeaways Explain This Topic AI
Virtual Switching Framework (VSF) combines multiple physical AOS-CX switches into a single logical device sharing a unified control plane, management IP, and configuration.
AOS-CX 6300 switches support stacks of up to 10 members, whereas CX 6200 switches support up to 8 members; entry-level CX 6000 and 6100 switches do not support VSF.
VSF roles are Conductor (runs the control plane), Standby (synchronized backup), and Member (line card); only the primary (member 1) and the configured secondary member can become Conductor or Standby.
Member 1 is always the primary member and normally the Conductor; vsf secondary-member <id> chooses the Standby. AOS-CX VSF does not use a configurable priority election.
Ring topologies provide N+1 link resiliency and degrade gracefully to a chain upon link failure, whereas chain topologies lack link redundancy and risk split-brain conditions.
Last updated: October 2026
3.1 Virtual Switching Framework (VSF) Architecture and Topologies
In modern enterprise campus networks, managing dozens or hundreds of standalone access switches introduces significant administrative overhead and operational complexity. Traditional designs require network engineers to configure independent management IP addresses, manage isolated configuration files, and rely on Spanning Tree Protocol (STP) to block redundant uplinks to prevent Layer 2 loops. Virtual Switching Framework (VSF) solves these operational bottlenecks by virtualizing multiple physical switches into a single logical chassis.
VSF operates on a single control plane and distributed data plane model. All switches participating in a VSF stack share a single configuration file, a single operational state database, and a single management IP address for SSH, REST API, Web GUI, and Aruba Central management. From the perspective of network administrators and neighboring devices, the entire stack functions as one high-capacity modular switch.
AOS-CX Hardware Portfolio and VSF Support
Not all switches in the Aruba CX switching portfolio support VSF stacking. Stacking capabilities are architected into access-layer platforms designed for flexible wiring closet aggregation:
Aruba CX 6300 Series (CX 6300F and CX 6300M): High-performance campus access and aggregation switches supporting up to 10 members in a single VSF stack. They support 10G, 25G, and 50G transceiver options for high-bandwidth stacking interconnects.
Aruba CX 6200F Series: Enterprise access switches supporting up to 8 members in a single VSF stack. Stacking interconnects use the SFP+ uplink ports, and the VSF guide notes that 12-port 6200 models cannot stack with 24- or 48-port models.
Aruba CX 6000 and CX 6100 Series: Entry-level Layer 2 access switches that do not support VSF stacking . These devices operate strictly as standalone switches.
Aruba CX 6400, CX 8100, CX 8325, CX 8360, and CX 8400 Series: Core and aggregation platforms that use Virtual Switching Extension (VSX) rather than VSF, providing independent dual control planes.
VSF Member Roles and Responsibilities
Within every VSF stack, each physical switch is assigned one of three operational roles: Conductor (called Commander or Master in older material), Standby , or Member (AOS-CX 10.14 VSF Guide). +-----------------------------------------------------------------------+
- | VSF LOGICAL CHASSIS |
- | |
- | +--------------------+ +--------------------+ +-----------------+ |
- | | Member 1 | | Member 2 | | Member 3..N | |
- | | CONDUCTOR | | STANDBY | | MEMBER | |
- | | Active Mgmt/Ctrl | | Synchronized State | | Local Forwarding| |
- | | STP/OSPF/LACP Engine| | Ready for SSO | | ASIC Data Plane | |
- | +---------+----------+ +---------+----------+ +--------+--------+ |
- | | | | |
- | +====== VSF Stacking Interconnect Links =======+ |
- +-----------------------------------------------------------------------+
- 1. The Conductor (formerly Commander / Master)
Runs the unified AOS-CX operating system control and management planes.
Manages all active network protocols, including Spanning Tree Protocol (STP), Link Aggregation Control Protocol (LACP), Open Shortest Path First (OSPF), Address Resolution Protocol (ARP), and Dynamic Host Configuration Protocol (DHCP) snooping.
Processes all inbound management sessions (console, SSH, HTTPS, SNMP, and network telemetry agents).
Maintains the stack configuration and software images and synchronizes the configuration database to the Standby switch.
Programs forwarding tables (MAC address tables, ARP tables, and IP route tables) into local and remote switch hardware Application-Specific Integrated Circuits (ASICs).
2. The Standby (Warm / Hot Standby)
Operates as the backup control plane engine for the stack.
Maintains a synchronized copy of the Conductor's configuration database over the VSF links.
Does not process active control protocols or respond to external management queries while in Standby status.
Automatically assumes the Conductor role if connectivity to the existing Conductor is lost through a hardware or link failure, so the remaining members keep forwarding without a full stack reload.
3. The Member (Line Card)
Operates functionally as an intelligent line card within a modular chassis.
Does not run independent control plane or management plane processes.
Uses its local switch ASICs to forward traffic at wire speed; its interfaces are directly controlled and programmed by the Conductor.
If local destination ports are unavailable, Member switches forward packets across VSF stacking links to reach target interfaces on adjacent members.
Primary, Secondary, and How Roles Are Assigned
AOS-CX VSF does not elect the Conductor by a configurable priority value. The rules in the AOS-CX 10.14 VSF Guide are deterministic:
Primary member = member 1. This is not configurable; a factory-default switch boots as VSF member 1. During normal operation the primary member is the Conductor .
Secondary member = your choice. Any member ID other than 1 can be configured as the secondary with vsf secondary-member <id> . During normal operation the secondary is the Standby . Auto-stacking assigns member 2 as the secondary.
Nobody else qualifies. Members other than the primary and secondary can never become Conductor or Standby.
Unique member IDs. Each switch needs a unique member ID; a member ID conflict stops the new switch from joining. switch# configure
- switch(config)# vsf secondary-member 2
- switch(config)# vsf member 2
- switch(vsf-member-2)# type jl666a
- switch(vsf-member-2)# link 1 2/1/25
- switch(vsf-member-2)# link 2 2/1/26
Best practice is to configure a secondary member (a stack without a Standby has no control-plane redundancy), take uplinks from both the primary and secondary members, and connect both members' management ports to the management network.
Interface Numbering and VSF Links
In standalone switches, physical interfaces follow a two-tier syntax ( slot/port , such as 1/1 or 1/48 ). In a VSF stack, interfaces adopt a three-tier syntax to identify member location:
member / slot / port \text{member} / \text{slot} / \text{port} member / slot / port
For example, interface 1/1/48 represents Member 1, Slot 1, Port 48. Interface 3/1/12 designates Member 3, Slot 1, Port 12. This numbering convention provides uniform port addressing across the entire unified stack.
Every VSF stack member supports up to two logical VSF links, designated as Link 1 and Link 2 ( link <1-2> <interface-range> under vsf member <id> ):
Each VSF link can contain multiple physical ports, and all VSF links in a stack should operate at the same speed. Once a port is added to a VSF link, its previous configuration is removed and it can connect only to another VSF port.
Combining multiple physical ports into a single VSF link forms an internal link aggregation group, increasing inter-switch backplane throughput and eliminating single points of physical cabling failure.
VSF Topologies: Ring vs. Chain
Stack members interconnect using either a Ring topology or a Chain (linear) topology. The physical interconnection scheme directly dictates stack survivability.
Topology Attribute VSF Ring Topology VSF Chain Topology
Physical Cabling Closed loop: Link 2 of each member connects to Link 1 of next member; last member connects back to Member 1 Open linear sequence: Last member does not loop back to Member 1
Link Redundancy Resilient ( N + 1 N+1 N + 1 path protection) No link redundancy (single point of failure)
Failure Behavior A single link or member failure does not isolate the remaining members; the ring operates as a chain A single link or member failure can split the stack into fragments (use split detection)
Bandwidth Utilization Bi-directional shortest path traffic forwarding Traffic traverses linear hops; intermediate links carry heavy transit traffic
Operational Recommendation Strongly recommended by HPE whenever feasible Supported, but plan split detection and expect disruption on a split
In a Ring topology , each member switch connects to two immediate neighbors. If a single stacking cable fails or a port encounters an SFP transceiver fault, the VSF ring gracefully degrades into a functional chain topology. All members retain connectivity to the Conductor and Standby, avoiding a stack split and maintaining network service.