Study guide
13.2 Molar Solutions, Normality & Buffer Preparation
ASCP Histotechnician HT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Fixation Principles & Aldehyde Fixatives
1.1 Principles and Chemistry of Fixation 1.2 Formalin Formulations and Aldehydes 1.3 Fixation Artifacts and Pigment Removal
2 Chapter 2: Compound Fixatives & Specimen Management
2.1 Metallic and Compound Fixatives 2.2 Non-Additive Fixatives & Special Fixation Applications 2.3 Specimen Accessioning, Grossing & Special Tissue Handling
3 Chapter 3: Tissue Processing Sequence & Reagents
3.1 Dehydration Principles and Reagents 3.2 Clearing Agents, Solvents & Safety Alternatives 3.3 Infiltration Media, Paraffin Properties & Additives
4 Chapter 4: Processors, Protocols & Decalcification
4.1 Automated Tissue Processors, Protocols & Maintenance 4.2 Decalcification Chemistry: Acid vs. Chelating Agents 4.3 Decalcification Endpoints, Artifacts & Surface Decal
5 Chapter 5: Embedding & Microtomy Techniques
5.1 Tissue Orientation & Paraffin Embedding Protocols 5.2 Rotary Microtome Mechanics, Knives & Clearance Angle 5.3 Sectioning Technique, Flotation Bath & Slide Adhesives
6 Chapter 6: Microtomy Artifacts & Cryotomy
6.1 Microtomy Artifacts, Defects & Troubleshooting 6.2 Cryostat Operation, Frozen Sections & Temperature Control 6.3 Cryosectioning Artifacts, Rapid Stains & Cryostat Safety
7 Chapter 7: Routine Hematoxylin & Eosin (H&E) Staining
7.1 Dye Chemistry, Mordants & Hematoxylin Formulations 7.2 Eosin Formulations, Differentiation & Bluing Agents 7.3 Automated Staining, Mounting, Coverslipping & H&E QC
8 Chapter 8: Special Stains — Carbohydrates & Connective Tissue
8.1 Glycogen, Neutral Mucins & Periodic Acid-Schiff (PAS) 8.2 Acid Mucins & Proteoglycans: Alcian Blue & Mucicarmine 8.3 Connective Tissue: Masson Trichrome & Collagen Stains 8.4 Basement Membranes, Movat Pentachrome & Multi-Element Connective Tissue Stains
9 Chapter 9: Special Stains — Fibers, Microorganisms, Pigments, Minerals & Lipids
9.1 Reticular & Elastic Fibers: Silver Impregnation & Verhoeff Stains 9.2 Microorganism Demonstration: Bacteria, Fungi & Spirochetes 9.3 Pigments, Minerals & Amyloid Demonstration 9.4 Lipid Histochemistry: Oil Red O, Sudan Dyes & Frozen-Section Requirements
10 Chapter 10: Special Stains — Nerve, Bone Marrow, Cytology & Tissue Components
10.1 Nerve Tissue & Myelin: Luxol Fast Blue, Bielschowsky & Silver Methods 10.2 Bone Marrow & Hematopoietic Preparations: Romanowsky, Giemsa & Wright Stains 10.3 Cytologic Preparations, Cell Blocks & the Papanicolaou Stain 10.4 Fibrin, Mast Cells & Other Tissue Components: PTAH, Toluidine Blue & Metachromasia
11 Chapter 11: Immunohistochemistry (IHC) & Molecular Staining
11.1 Principles of Antigen-Antibody Binding & Selection 11.2 Antigen Retrieval (HIER vs. PIER) & Endogenous Blocking 11.3 Detection Systems, Chromogens, Controls & Troubleshooting
12 Chapter 12: Laboratory Safety, Quality Control & Operations
12.1 OSHA Chemical Safety & Formaldehyde Exposure Monitoring 12.2 Biological Safety, Sharps Handling & Hazardous Waste Management 12.3 Quality Assurance, CLIA/CAP Compliance & Records Retention 12.4 Compound Light Microscopy, Optics & Kohler Illumination
13 Chapter 13: Laboratory Mathematics, Ancillary Equipment & Reagent Quality Control
13.1 Metric System, Percent Solutions & Dilutions 13.2 Molar Solutions, Normality & Buffer Preparation 13.3 Ancillary Laboratory Equipment, Water Quality & Solvent Recovery
13.2 Molar Solutions, Normality & Buffer Preparation
Key Takeaways Explain This Topic AI
Grams of solute for a molar solution equals molarity multiplied by formula weight multiplied by volume in litres.
Hydrated salts must be weighed using the formula weight that includes the waters of crystallization, or the buffer will be under-concentrated.
Normality equals molarity multiplied by the number of reactive equivalents, so 1 M sulfuric acid is 2 N while 1 M sodium hydroxide is 1 N.
The molarity of a concentrated acid equals ten times its percent purity times its density, divided by its formula weight; concentrated hydrochloric acid is approximately 12 M.
pH meters are calibrated with at least two standard buffers that bracket the expected sample pH, and the electrode is stored in its manufacturer-specified storage solution rather than distilled water.
Last updated: September 2026
13.2 Molar Solutions, Normality & Buffer Preparation
ASCP HT Exam Focus: Molar solutions is a named sub-topic under Laboratory Mathematics. Molarity questions on the ASCP HT examination almost always involve either a hydrated salt or a concentrated acid , because those are the two places where a plausible-looking wrong answer is easy to construct.
Molarity
A mole is the formula weight of a substance expressed in grams. Molarity (M) is moles of solute per litre of finished solution . Grams = M × formula weight × volume in litres \text{Grams} = M \times \text{formula weight} \times \text{volume in litres} Grams = M × formula weight × volume in litres
Worked example. Prepare 500 mL of 0.1 M citric acid (formula weight 192.12 g/mol) for a retrieval buffer: Grams = 0.1 × 192.12 × 0.500 = 9.61 g \text{Grams} = 0.1 \times 192.12 \times 0.500 = \mathbf{9.61\text{ g}} Grams = 0.1 × 192.12 × 0.500 = 9.61 g
Worked example. Prepare 2 L of 0.5 M sodium chloride (formula weight 58.44): Grams = 0.5 × 58.44 × 2.0 = 58.44 g \text{Grams} = 0.5 \times 58.44 \times 2.0 = \mathbf{58.44\text{ g}} Grams = 0.5 × 58.44 × 2.0 = 58.44 g
Millimolar (mM). Retrieval buffers are usually written in millimolar: 10 mM = 0.010 M 10\text{ mM} = 0.010\text{ M} 10 mM = 0.010 M . A 10 mM citrate buffer is therefore one hundredth the mass of a 1 M solution.
Waters of Hydration
Many laboratory salts are supplied as hydrates, and the water is part of the mass you weigh.
Salt Anhydrous FW Hydrated form Hydrated FW
Sodium phosphate dibasic 141.96 Na 2 HPO 4 ⋅ 7 H 2 O \text{Na}_2\text{HPO}_4 \cdot 7\text{H}_2\text{O} Na 2 HPO 4 ⋅ 7 H 2 O 268.07
Sodium citrate 258.07 Na 3 C 6 H 5 O 7 ⋅ 2 H 2 O \text{Na}_3\text{C}_6\text{H}_5\text{O}_7 \cdot 2\text{H}_2\text{O} Na 3 C 6 H 5 O 7 ⋅ 2 H 2 O 294.10
Copper sulfate 159.61 CuSO 4 ⋅ 5 H 2 O \text{CuSO}_4 \cdot 5\text{H}_2\text{O} CuSO 4 ⋅ 5 H 2 O 249.68
EDTA disodium 336.21 Na 2 EDTA ⋅ 2 H 2 O \text{Na}_2\text{EDTA} \cdot 2\text{H}_2\text{O} Na 2 EDTA ⋅ 2 H 2 O 372.24
Worked example. Prepare 1 L of 10 mM sodium citrate buffer using the dihydrate : Grams = 0.010 × 294.10 × 1.0 = 2.94 g \text{Grams} = 0.010 \times 294.10 \times 1.0 = \mathbf{2.94\text{ g}} Grams = 0.010 × 294.10 × 1.0 = 2.94 g
Using the anhydrous formula weight by mistake would give 2.58 g - a buffer roughly 12 percent weak, which in a heat-induced epitope retrieval protocol shows up as weak, patchy immunostaining.
Rule: read the label, not the name. If the bottle says "dihydrate", use the dihydrate formula weight printed on that label.
Normality and Equivalents
Normality (N) is equivalents of solute per litre . An equivalent is the amount of substance that supplies one mole of reactive units - one mole of H + \text{H}^{+} H + for an acid, one mole of OH − \text{OH}^{-} OH − for a base, or one mole of charge for a salt. N = M × number of equivalents Equivalent weight = formula weight number of equivalents N = M \times \text{number of equivalents} \qquad \text{Equivalent weight} = \frac{\text{formula weight}}{\text{number of equivalents}} N = M × number of equivalents Equivalent weight = number of equivalents formula weight
- Reagent Equivalents Relationship
- HCl 1 1 M = 1 N
- NaOH 1 1 M = 1 N
- H 2 SO 4 \text{H}_2\text{SO}_4 H 2 SO 4 2 1 M = 2 N
- Ca ( OH ) 2 \text{Ca}(\text{OH})_2 Ca ( OH ) 2 2 1 M = 2 N
Worked example. Prepare 500 mL of 1 N sulfuric acid from the solid-equivalent calculation: the equivalent weight is 98.08 / 2 = 49.04 98.08 / 2 = 49.04 98.08/2 = 49.04 , so 1 × 49.04 × 0.500 = 24.52 g 1 \times 49.04 \times 0.500 = \mathbf{24.52\text{ g}} 1 × 49.04 × 0.500 = 24.52 g of equivalent mass, delivered in practice by diluting the concentrated acid.
Converting a Concentrated Acid to Molarity
Concentrated reagents are labelled as percent weight/weight with a density , not as molarity. The conversion is: M = 10 × % ( w/w ) × density in g/mL formula weight M = \frac{10 \times \%\ (\text{w/w}) \times \text{density in g/mL}}{\text{formula weight}} M = formula weight 10 × % ( w/w ) × density in g/mL
- Concentrated reagent Percent (w/w) Density Formula weight Approximate molarity
- Hydrochloric acid 37 1.19 36.46 12.1 M
- Sulfuric acid 96 1.84 98.08 18.0 M
- Nitric acid 70 1.42 63.01 15.8 M
- Glacial acetic acid 99.7 1.05 60.05 17.4 M
- Ammonium hydroxide 28 0.90 35.05 7.2 M
Worked example. Prepare 1 L of 1 M hydrochloric acid from the concentrated reagent: V 1 = ( 1 × 1000 ) / 12.1 = 82.6 mL V_1 = (1 \times 1000)/12.1 = \mathbf{82.6\text{ mL}} V 1 = ( 1 × 1000 ) /12.1 = 82.6 mL of concentrated HCl added slowly to roughly 900 mL of water, then brought to 1 L. Acid is always added to water, because the heat of dilution released at the interface can flash-boil water added to acid.
Buffers That Histology Actually Prepares
- Buffer Composition pH Use
- Citrate 10 mM sodium citrate 6.0 Standard heat-induced epitope retrieval
- Tris-EDTA 10 mM Tris base with 1 mM EDTA 9.0 High-pH retrieval for nuclear hormone receptors
Phosphate-buffered saline (PBS) Sodium phosphate with sodium chloride 7.2 to 7.4 Antibody diluent and wash buffer
- Neutral buffered formalin Sodium phosphate monobasic and dibasic 6.8 to 7.2 Routine fixative
- Scott tap water substitute Magnesium sulfate with sodium bicarbonate approximately 8.0 Bluing hematoxylin
A buffer resists pH change because it contains a weak acid and its conjugate base in equilibrium, described by the Henderson-Hasselbalch relationship : pH = p K a + log [ conjugate base ] [ weak acid ] \text{pH} = \text{p}K_a + \log\frac{[\text{conjugate base}]}{[\text{weak acid}]} pH = p K a + lo g [ weak acid ] [ conjugate base ]
Buffering capacity is greatest when the two species are roughly equal, which is one pH unit either side of the p K a \text{p}K_a p K a . A buffer used far from its p K a \text{p}K_a p K a drifts, which is why citrate is used near pH 6 and Tris near pH 8 to 9 rather than interchangeably.
pH Meter Calibration
Calibrate with at least two standard buffers that bracket the expected sample pH - typically pH 7.00 with pH 4.01 for acidic work, or pH 7.00 with pH 10.01 for alkaline retrieval buffers.
Verify the electrode slope falls within the manufacturer's acceptance range; a drifting or out-of-slope electrode is a replacement item, not a recalibration item.
Use temperature compensation , because electrode response and buffer pH both change with temperature. Measure standards and samples at the same temperature.
Store the electrode in the manufacturer-specified storage solution (commonly potassium chloride), never in distilled water, which leaches ions out of the junction.
Rinse with deionized water between measurements and blot rather than wipe, to avoid static charge on the bulb.
Document calibration in the instrument log with the standards used, lot numbers, and the technologist's initials.