Study guide
4.4 Pushrods, Rocker Arms, & Overhead Camshaft Inspection
ASE A1 Engine Repair Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Engine Diagnostic Fundamentals
1.1 ASE A1 Exam Structure & Certification Requirements 1.2 Engine Diagnostic Strategy & Tool Usage 1.3 Engine Noise, Vibration, & Smoke Analysis
2 General Engine Diagnosis: Mechanical Testing
2.1 Cranking & No-Start Diagnostic Procedures 2.2 Engine Performance & Misfire Troubleshooting 2.3 Vacuum Gauge Testing & Dynamic Pressure Analysis 2.4 Compression & Cylinder Leak-Down Testing
3 General Engine Diagnosis: DTCs & Fluid Analysis
3.1 Engine Fluid Leak & Contamination Analysis 3.2 OBD-II Diagnostic Trouble Codes & Scan Tool Live Data 3.3 Mechanical Noise & Internal Clearance Diagnostics 3.4 Exhaust System & Backpressure Diagnostics
4 Cylinder Head & Valve Train Diagnosis and Repair
4.1 Cylinder Head Removal, Disassembly, & Inspection 4.2 Valve Train Component Inspection & Service 4.3 Valve Lash Adjustment & Hydraulic Lash Adjuster Diagnostics 4.4 Pushrods, Rocker Arms, & Overhead Camshaft Inspection
5 VVT & Timing Systems Diagnostics and Repair
5.1 Variable Valve Timing (VVT) Systems & Phaser Diagnostics 5.2 Timing Belt & Timing Chain Inspection & Replacement 5.3 Camshaft & Lifter/Follower Service Procedures
6 Engine Block Diagnosis and Repair
6.1 Engine Block Inspection, Cleaning, & Machining 6.2 Crankshaft & Main/Rod Bearing Service 6.3 Piston, Piston Pin, & Piston Ring Fitting 6.4 Balance Shafts, Flywheel, & Engine Assembly Verification
7 Lubrication and Cooling Systems Diagnosis and Repair
7.1 Oil Pressure Testing & Low/High Pressure Diagnostics 7.2 Oil Pump Inspection, Overhaul, & Relief Valve Service 7.3 Cooling System Inspection, Pressure Testing, & Cap Diagnostics 7.4 Thermostat, Water Pump, & Fan Control Diagnostics
8 Fuel, Electrical, Ignition, & Exhaust Subsystems
8.1 Ignition System Testing & Spark Component Diagnostics 8.2 Fuel Delivery, Pressure Testing, & Injector Diagnostics 8.3 Air Induction System, Throttle Body, & PCV Inspection 8.4 Exhaust System Diagnosis & Service
4.4 Pushrods, Rocker Arms, & Overhead Camshaft Inspection
Key Takeaways Explain This Topic AI
Pushrod straightness is measured on V-blocks with a dial indicator; maximum allowable runout is 0.005 in (0.13 mm).
Rocker arm contact pads must be checked for wear grooves that destroy valvetrain geometry and side-load valve stems.
Cam lobe lift is calculated by subtracting the base circle (minor axis) from the major axis height using an outside micrometer.
Overhead camshaft journal clearance is checked with Plastigage (spec 0.001-0.0025 in); excessive clearance drops top-end oil pressure.
Variable Valve Timing (VVT) cam phasers require clean OCV screens and an intact locking pin to prevent 2-3 second cold-start rattles.
Last updated: July 2026
Pushrods, Rocker Arms, & Overhead Camshaft Inspection
The transfer of motion from the camshaft to the valves involves critical intermediate components in pushrod (OHV) engines and direct-drive components in overhead camshaft (OHC/DOHC) systems. Precision inspection of pushrods, rocker arm assemblies, camshaft lobes, camshaft journals, and variable valve timing (VVT) actuators is required during any cylinder head or valvetrain diagnostic procedure.
Pushrod Inspection & Straightness Specifications
In overhead valve (OHV) engines, pushrods transmit motion upward from the hydraulic or mechanical lifters to the rocker arms. Many hollow pushrods also function as oil passages, carrying pressurized engine oil up to lubricate the rocker arms and valve tips.
Pushrod Straightness Inspection
A bent pushrod restricts valve lift, alters valve timing, and rubs against the pushrod guide plates or cylinder head passages, creating metal debris.
Glass Plate Test: Roll the pushrod across a precision ground glass or granite surface plate. Any wobble or gap between the pushrod shank and glass indicates a bent pushrod.
Dial Indicator on V-Blocks: Place the pushrod ends on precision V-blocks. Position a dial indicator plunger at the center of the pushrod shank. Rotate the pushrod 360 degrees.
Maximum Allowable Runout: 0.005 in (0.13 mm) Total Indicator Reading (TIR). Any pushrod exceeding 0.005 in runout must be replaced; never attempt to straighten a bent pushrod. Pushrod Dial Indicator Runout Measurement:
- Dial Indicator
- [ 0 ]
- |
- v
- ==========o========== <--- Pushrod Shank
- / [V] [V] <--- V-Blocks supporting ends
- Pushrod Tip & Oil Passage Inspection
Spherical Ball Ends & Cups: Inspect both ends for scuffing, scoring, pitting, or flat spots. Damaged tips ruin rocker arm cups and lifter seats.
Oil Passage Clearance: Hold the pushrod up to a light source or blow compressed air through the hollow center to verify that the internal oil hole is completely unblocked.
Rocker Arm & Shaft Assembly Service
Rocker arms pivot to reverse and multiply camshaft lift (rocker arm ratio, typically 1.5:1 to 1.7:1). Types of Rocker Arm Assemblies:
- 1. Stamped Steel (Stud-Mounted with Fulcrum Ball)
- 2. Pedestal-Mounted (Cast/Forged with Trunnion Pivot)
- 3. Shaft-Mounted Rocker Arms (Bronze Bushings on Heavy Shaft)
- 4. Roller-Tip Rocker Arms (Needle-Bearing Pivot & Roller Tip)
- Rocker Arm Wear Inspection
Valve Tip Contact Pad: Inspect the pad that contacts the valve stem tip. Minor wear patterns are acceptable, but any deep wear groove, pitting, or ridging requires rocker arm replacement. A grooved contact pad prevents accurate feeler gauge adjustment and applies destructive side-thrust loads to the valve stem.
Fulcrum Ball & Pivot Trunnion: Inspect stamped steel fulcrum balls and cast trunnions for galling, heat discoloration (blueing), and scoring caused by oil starvation.
Shaft-Mounted Assemblies: On shaft-mounted rocker systems, measure the outer diameter of the rocker shaft with a micrometer and the inner diameter of the rocker arm bronze bushings with an inside micrometer. Maximum allowable shaft-to-bushing clearance is 0.002 in (0.05 mm) .
Rocker Shaft Installation Warning: When reinstalling rocker shafts, ensure the oil feed holes in the shaft face DOWNWARD toward the engine block (away from the load side). Installing a rocker shaft upside-down cuts off lubrication, destroying all rocker bushings within minutes.
Overhead Camshaft (OHC) & Journal Inspection
Overhead camshafts open valves directly through bucket followers or finger followers.
Cam Lobe Lift Measurement
Camshaft lobes convert rotary motion to linear lift. Wear on cam lobes reduces valve opening lift, suffocating cylinder air intake.
On-Engine Dial Indicator Method: Mount a dial indicator parallel to the valve stem with the indicator tip resting on the spring retainer or follower. Rotate the crankshaft by hand and record the peak reading (Total Indicator Reading). Compare to factory lobe lift specs.
Micrometer Measurement Formula: Measure the cam lobe using an outside micrometer across two axes: Net Cam Lobe Lift = Major Axis (Lobe Height) − Minor Axis (Base Circle Diameter) \text{Net Cam Lobe Lift} = \text{Major Axis (Lobe Height)} - \text{Minor Axis (Base Circle Diameter)} Net Cam Lobe Lift = Major Axis (Lobe Height) − Minor Axis (Base Circle Diameter) Overhead Camshaft Lobe Lift Calculation Table:
- +-------------------------------------+-----------------------+-----------------------+
- | Lobe Dimension Parameter | Imperial Measurement | Metric Measurement |
- +-------------------------------------+-----------------------+-----------------------+
- | Major Axis (Lobe Peak Height) | 1.550 in | 39.37 mm |
- | Minor Axis (Base Circle Diameter) | 1.250 in | 31.75 mm |
- | Calculated Net Cam Lobe Lift | 0.300 in | 7.62 mm |
- +-------------------------------------+-----------------------+-----------------------+
Result: Lobe lift is 0.300 in. Lobe wear exceeding 0.003-0.005 in requires cam replacement.
Camshaft Journal Clearance & Plastigage Testing
Camshaft journals support the spinning camshaft inside aluminum cylinder head bores.
Plastigage Measurement Procedure:
Wipe all oil off camshaft journals and bearing caps.
Lay a strip of flexible Plastigage across each camshaft journal.
Install the camshaft bearing caps and torque the cap bolts to OEM specification (typically 8–12 lb-ft) in a progressive cross-pattern. Do NOT rotate the camshaft while Plastigage is installed.
Remove the bearing caps and measure the flattened Plastigage width using the graduated scale on the Plastigage envelope.
- OHC Inspection Parameter Standard Specification Range Diagnostic Consequence of Excessive Wear
- Cam Lobe Wear Limit Max 0.003 in (0.08 mm) wear Reduced engine horsepower, misfire, valvetrain noise
Journal-to-Bearing Clearance 0.0010 in to 0.0025 in (0.025-0.063 mm) Low top-end oil pressure, cam chatter, VVT faults
Camshaft Endplay (Thrust) 0.002 in to 0.007 in (0.05-0.18 mm) Cam walking, timing belt/chain misalignment, clatter
Non-Replaceable Bearings Warning: Most modern aluminum cylinder heads feature integrated camshaft bearing bores with no separate bearing inserts. If Plastigage reveals journal clearance exceeding 0.0035 in (0.09 mm) due to scoring or oil starvation, the entire cylinder head assembly must be replaced or precision line-bored by a specialist.
Variable Valve Timing (VVT) Actuator & Phaser Inspection
Variable Valve Timing (VVT) systems rotate the camshaft relative to its drive sprocket to optimize engine efficiency, emissions, and power across RPM ranges. VVT Hydraulic Control Flow System:
- Engine Oil Pan ---> Oil Pump ---> Oil Control Valve (OCV Solenoid)
- |
- v (Pushes hydraulic oil)
- VVT Cam Phaser Gear Assembly
- (Advance / Retard Chambers)
Oil Control Solenoid (OCV) & Mesh Filters: The OCV directs pressurized engine oil into advance or retard passages inside the VVT phaser. Small wire mesh filter screens are installed in the cylinder head oil galleries feeding the OCV. Sludge or debris clogging the OCV mesh screen restricts oil flow , causing slow VVT response, camshaft timing DTCs (e.g., P0011, P0014), and engine stalling at idle.
Internal Phaser Locking Pin Wear: Inside the VVT cam phaser gear is a spring-loaded mechanical locking pin. This pin locks the phaser at its base park position during engine cranking before oil pressure builds. If the locking pin or its locking hole becomes worn, the phaser vanes slap back and forth during engine cranking, producing a loud metallic rattle for 2 to 3 seconds during cold starts . Once oil pressure fills the phaser chambers, the rattle disappears. A damaged VVT phaser assembly must be replaced.