Study guide
4.3 Valve Lash Adjustment & Hydraulic Lash Adjuster Diagnostics
ASE A1 Engine Repair Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Engine Diagnostic Fundamentals
1.1 ASE A1 Exam Structure & Certification Requirements 1.2 Engine Diagnostic Strategy & Tool Usage 1.3 Engine Noise, Vibration, & Smoke Analysis
2 General Engine Diagnosis: Mechanical Testing
2.1 Cranking & No-Start Diagnostic Procedures 2.2 Engine Performance & Misfire Troubleshooting 2.3 Vacuum Gauge Testing & Dynamic Pressure Analysis 2.4 Compression & Cylinder Leak-Down Testing
3 General Engine Diagnosis: DTCs & Fluid Analysis
3.1 Engine Fluid Leak & Contamination Analysis 3.2 OBD-II Diagnostic Trouble Codes & Scan Tool Live Data 3.3 Mechanical Noise & Internal Clearance Diagnostics 3.4 Exhaust System & Backpressure Diagnostics
4 Cylinder Head & Valve Train Diagnosis and Repair
4.1 Cylinder Head Removal, Disassembly, & Inspection 4.2 Valve Train Component Inspection & Service 4.3 Valve Lash Adjustment & Hydraulic Lash Adjuster Diagnostics 4.4 Pushrods, Rocker Arms, & Overhead Camshaft Inspection
5 VVT & Timing Systems Diagnostics and Repair
5.1 Variable Valve Timing (VVT) Systems & Phaser Diagnostics 5.2 Timing Belt & Timing Chain Inspection & Replacement 5.3 Camshaft & Lifter/Follower Service Procedures
6 Engine Block Diagnosis and Repair
6.1 Engine Block Inspection, Cleaning, & Machining 6.2 Crankshaft & Main/Rod Bearing Service 6.3 Piston, Piston Pin, & Piston Ring Fitting 6.4 Balance Shafts, Flywheel, & Engine Assembly Verification
7 Lubrication and Cooling Systems Diagnosis and Repair
7.1 Oil Pressure Testing & Low/High Pressure Diagnostics 7.2 Oil Pump Inspection, Overhaul, & Relief Valve Service 7.3 Cooling System Inspection, Pressure Testing, & Cap Diagnostics 7.4 Thermostat, Water Pump, & Fan Control Diagnostics
8 Fuel, Electrical, Ignition, & Exhaust Subsystems
8.1 Ignition System Testing & Spark Component Diagnostics 8.2 Fuel Delivery, Pressure Testing, & Injector Diagnostics 8.3 Air Induction System, Throttle Body, & PCV Inspection 8.4 Exhaust System Diagnosis & Service
4.3 Valve Lash Adjustment & Hydraulic Lash Adjuster Diagnostics
Key Takeaways Explain This Topic AI
Mechanical valve lash must be set with the cylinder at TDC compression to ensure followers rest on the cam base circle.
Exhaust valve lash specifications are wider than intake specs to account for higher thermal expansion rates.
Hydraulic lash adjusters maintain zero mechanical lash automatically; stud-mounted rockers require setting zero lash plus specified preload.
Aerated or foamed engine oil caused by overfilling the oil pan traps air in lifters, leading to rapid lifter collapse and loud clatter.
Overhead camshaft bucket lifter shim adjustments use the formula: New Shim = (Measured Lash - Specified Lash) + Present Shim.
Last updated: July 2026
Valve Lash Adjustment & Hydraulic Lash Adjuster Diagnostics
Engine valvetrain operation requires precise control over the clearance between the camshaft profile and the valve stem tip. Depending on engine design, valvetrains utilize either mechanical (solid) valve lash systems or hydraulic lash adjusters (HLAs / hydraulic lifters). Technicians must master mechanical lash setting, shim math for overhead camshafts, and diagnostic procedures for hydraulic lifter noise and oiling faults.
Mechanical vs. Hydraulic Valvetrain Comparison
Operating Parameter Mechanical (Solid Lifter) Valvetrain Hydraulic Lash Adjuster (HLA) Valvetrain
Lash Requirement Prescribed mechanical gap required when cold Zero mechanical clearance maintained during operation
Thermal Expansion Lash absorbs expansion of stem/pushrod when hot Internal plunger adjusts automatically to thermal changes
Maintenance Periodic inspection and manual lash adjustment required Maintenance-free; self-adjusting via engine oil pressure
High-RPM Performance Superior precision at high RPM; no lifter pump-up Subject to lifter float or pump-up at ultra-high RPM
Noise Characteristics Slight mechanical clicking under normal operation Completely silent operation when working correctly
Mechanical Valve Lash Adjustment Procedures
Mechanical valvetrains must have clearance (lash) when cold to ensure that as the valve stem and valvetrain components expand with engine heat, the valve is not held off its seat.
Consequences of Incorrect Lash:
Too Tight (Insufficient Lash): As the engine reaches operating temperature, thermal expansion holds the valve slightly open off its seat. This prevents proper heat dissipation through the seat, leading to burned valves, low compression, and engine misfires.
Too Loose (Excessive Lash): Causes noisy valvetrain clatter, reduces total valve lift and opening duration, degrades engine volumetric efficiency, and subjects valve stem tips and rocker arms to destructive hammering impact loads.
Setting Mechanical Lash (Pushrod & Screw-Adjustment OHC)
Engine Operating Temperature: Verify whether specs require cold or hot engine adjustment. Exhaust valves always require wider clearance than intake valves due to higher thermal expansion rates.
Cylinder Position: Rotate the crankshaft until the target cylinder is at Top Dead Center (TDC) on its Compression stroke . At TDC compression, both intake and exhaust cam lobes are facing completely away from the lifters (on the base circle).
Feeler Gauge Measurement: Insert the specified feeler gauge between the valve tip and rocker arm pad (or cam base circle and follower). Use the "Go/No-Go" gauge technique: the specified gauge must slide with a slight smooth drag, while a gauge 0.002 in thicker must not enter the gap.
Locking Mechanism: Hold the adjustment screw stationary using a screwdriver or Allen wrench while tightening the locknut with a box wrench. Re-check feeler gauge drag after tightening the locknut, as torquing can alter the setting.
Overhead Camshaft (OHC) Bucket Lifter Shim Calculations
Many OHC and DOHC engines utilize bucket-type followers with selective adjustment shims located either over the bucket (shim-over-bucket) or under the bucket (shim-under-bucket).
The OHC Shim Calculation Formula New Shim Thickness = ( Measured Clearance − Specified Clearance ) + Present Shim Thickness \text{New Shim Thickness} = (\text{Measured Clearance} - \text{Specified Clearance}) + \text{Present Shim Thickness} New Shim Thickness = ( Measured Clearance − Specified Clearance ) + Present Shim Thickness Overhead Camshaft Shim Calculation Example Table:
- +-------------------------------------+-----------------------+-----------------------+
- | Parameter Description | Imperial Specification| Metric Specification |
- +-------------------------------------+-----------------------+-----------------------+
- | Factory Specified Clearance | 0.010 in | 0.25 mm |
- | Actual Measured Clearance | 0.014 in | 0.35 mm |
- | Measured Clearance Deviation | +0.004 in (Excessive) | +0.10 mm (Excessive) |
- | Present Shim Thickness Removed | 0.100 in | 2.54 mm |
- | Calculated New Shim Thickness Needed| 0.104 in | 2.64 mm |
- +-------------------------------------+-----------------------+-----------------------+
Result: Installing a 0.104 in (2.64 mm) shim reduces lash by 0.004 in, restoring 0.010 in spec.
Procedure for Under-Bucket Systems: Under-bucket shims require removing the camshafts to access and exchange shims. Always measure and record all valve clearances before removing camshafts to minimize teardown cycles.
Hydraulic Lash Adjuster (HLA) Operation & Preload Setup
Hydraulic lash adjusters automatically maintain zero valvetrain lash using engine oil pressure. +-----------------------------+
- | Pushrod / Rocker Contact |
- +--------------+--------------+
- |
- +-----------+-----------+
- | Plunger Assembly |
- | (High-Pressure |
- | Oil Chamber) |
- +-----------+-----------+
- | <--- Internal Check Ball & Spring
- +-----------+-----------+
- | Lifter Body & Base |
- +-----------------------+
- ^
- Engine Oil Gallery Feed
Operating Principle: Low-pressure engine oil enters the lifter body oil groove and passes into the inner plunger. When the valve is closed, the plunger spring expands to eliminate all valvetrain play. As the cam lobe pushes against the lifter, oil inside the lower high-pressure chamber pushes upward against the check ball, sealing the chamber. Liquid oil cannot compress, transforming the lifter into a solid hydraulic column that opens the valve.
Setting Hydraulic Lifter Preload (Pedestal/Stud Rockers)
On adjustable pushrod engines, hydraulic lifters require setting plunger preload :
Rotate engine to TDC compression for the cylinder being adjusted.
Loosen the rocker arm nut, then slowly tighten it while rotating or wiggling the pushrod up and down with your fingers.
The exact point where vertical pushrod end-play is completely eliminated is Zero Lash .
From Zero Lash, tighten the rocker adjusting nut an additional specified turn (typically 1/4 to 1 full turn). This depresses the internal lifter plunger into the center of its operating travel range (preload).
Hydraulic Lifter Diagnostic & Troubleshooting Guide
Observed Valvetrain Symptom Probable Root Causes Recommended Diagnostic / Repair Action
Brief Ticking Noise (1-3 sec) on Cold Start Minor oil drain-back past check ball while parked overnight. Normal operation if noise stops immediately as oil pressure builds.
Continuous Loud Ticking at All Engine Speeds Clogged lifter oil port, stuck/varnished plunger, collapsed lifter spring, or low engine oil pressure (<10 psi). Check engine oil pressure with mechanical gauge; clean/replace lifters and flush oil passages.
Valvetrain Noise After High Speed Drive / Overfill Aerated/foamed engine oil due to crankcase overfilling or low oil level causing oil pump suction of air. Correct oil level to dipstick full mark; allow air bubbles to dissipate from crankcase oil.
Single Cylinder Misfire / Zero Compression Warm Hydraulic lifter "pump-up" (stuck plunger at top of stroke) holding valve open, or stuck oil pressure relief valve. Test cylinder compression cold vs warm; inspect lifter plunger movement and oil relief valve.
Hydraulic Lifter Bleed-Down Testing
A lifter leak-down (bleed-down) tester measures the time required for a hydraulic lifter plunger to collapse a specified distance under a constant load (e.g., 50 lbs) while submerged in testing oil.
Fast Bleed-Down: Indicates a worn check ball seat or excessive plunger-to-body clearance. Fast bleed-down causes lifter collapse and valvetrain clatter under heavy load.
Slow / No Bleed-Down: Indicates varnish deposits trapping the plunger. A stuck plunger acts like a solid lifter and can hold the valve open when hot.