Study guide
5.3 Tone Rings (Reluctor Rings) and Magnetic Sensor Ring Inspection
ASE Automobile & Light Truck Test A5: Brakes Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Hydraulic and Power Assist Systems Core
1.1 Master Cylinder Principles, Dual-Circuit Designs, and Operation 1.2 Master Cylinder Diagnosis, Bench Bleeding, and Pressure Testing 1.3 Hydraulic Lines, Hoses, and Fitting Service 1.4 Hydraulic System Bleeding Methods and Procedures 1.5 Hydraulic Control Valves: Metering, Proportioning, and Combination Valves 1.6 Vacuum Power Brake Booster Operation and Inspection 1.7 Vacuum Booster Diagnosis, Testing, and Replacement 1.8 Hydro-Boost and Electro-Hydraulic Power Assist Systems
2 Chapter 2: Parking Brake Systems & General Hydraulic Diagnosis
2.1 Parking Brake Mechanical Controls and Cable Assembly 2.2 Drum-Integrated Parking Brake Service and Adjustment 2.3 Caliper-Integrated Parking Brake Mechanics 2.4 Electronic Parking Brake (EPB) Systems and Service Modes 2.5 Brake Fluid Chemistry, Testing, and Specification 2.6 Hydraulic Leak Diagnosis and System Pressure Testing 2.7 Pedal Travel, Free-Play, and Height Adjustments 2.8 Brake System Noise, Vibration, and Harshness (NVH) Diagnostics
3 Chapter 3: Drum Brake Diagnosis and Repair
3.1 Drum Brake Architecture and Component Identification 3.2 Drum Brake Inspection and Micrometer Measurement 3.3 Brake Shoe Removal, Inspection, and Installation 3.4 Wheel Cylinder Inspection, Rebuilding, and Replacement 3.5 Self-Adjusting Mechanisms and Manual Adjustment 3.6 Drum Brake Troubleshooting: Dragging, Pulling, and Low Pedal
4 Chapter 4: Disc Brake Diagnosis and Repair
4.1 Disc Brake System Architecture: Floating, Sliding, and Fixed Calipers 4.2 Caliper Inspection, Overhaul, Slide Pin Lubrication, and Replacement 4.3 Brake Pad Inspection, Selection, Anti-Rattle Hardware, and Replacement 4.4 Brake Rotor Inspection, Dial Indicator Runout, and Micrometer Measurement 4.5 Rotor Machining: On-Car vs Off-Car Lathe Procedures 4.6 Wheel Lug Nut Torque, Hub Flange Cleaning, and Rotor Distortion 4.7 Wheel Bearing Diagnosis, Service, and Hub Assembly Replacement 4.8 Disc Brake Noise and Squeal Diagnostic Remediation 4.9 Disc Brake Pull, Drag, and Excessive Pedal Travel Diagnosis
5 Chapter 5: Electronic Brake Control Systems (ABS, TCS, ESC) Diagnosis and Repair
5.1 ABS Fundamentals, Control Cycles, and Hydraulic Operations 5.2 Wheel Speed Sensors: Passive (VR) vs Active (Hall-Effect) Sensors 5.3 Tone Rings (Reluctor Rings) and Magnetic Sensor Ring Inspection 5.4 ABS Hydraulic Control Unit (HCU) and Solenoid Valve Diagnosis 5.5 Traction Control Systems (TCS) Diagnostics and Engine Interface 5.6 Electronic Stability Control (ESC) and Sensor Inputs 5.7 Scan Tool Diagnostic Procedures, Live Data, and ABS Automated Bleeding 5.8 Advanced Electronic Braking: Regenerative Brake Integration and Brake-by-Wire
5.3 Tone Rings (Reluctor Rings) and Magnetic Sensor Ring Inspection
Key Takeaways Explain This Topic AI
A cracked or missing tooth on a traditional steel tone ring will cause an erratic WSS signal and false ABS activation.
Rust jacking under a pressed-on tone ring can cause the ring to expand, crack, and widen the air gap.
Modern active sensors often use a magnetic encoder ring integrated into the wheel bearing seal.
Magnetic encoder wheels must be inspected with a special magnetic test card to view the alternating north/south pole segments.
Installing a wheel bearing backwards (magnetic seal facing away from the sensor) will result in a hard ABS fault and 0 mph reading.
Last updated: July 2026
Reluctor Rings, Targets, and Magnetic Encoders
A wheel speed sensor cannot function in isolation; it requires a precisely engineered mechanical target attached to a rotating driveline or wheel component. As this target rotates past the sensor tip, it induces the magnetic flux variations or magnetoresistive resistance changes required to generate a speed signal. Technicians encounter two main target designs in modern automotive applications: traditional Toothed Steel Reluctor Rings (Tone Rings) and modern Magnetic Encoder Rings integrated into sealed wheel bearings.
Traditional Toothed Steel Reluctor Rings
Toothed reluctor rings (exciter rings) are precision-machined or sintered steel rings featuring evenly spaced teeth around their outer circumference. They are commonly pressed onto outer CV joint housings, axle shafts, or integrated directly into brake rotor hubs and differential ring gear assemblies.
Mechanical Failure Modes and Symptoms:
Cracked Tone Ring (Rust Jacking): In regions exposed to road salt, moisture penetrates beneath pressed-on steel tone rings mounted on cast iron CV joint housings. As the steel housing corrodes, the resulting iron oxide expansion ( rust jacking ) exerts tremendous radial pressure outward against the tone ring. Eventually, the steel tone ring fractures. The crack forces the two adjacent teeth apart, creating a single extra-wide gap.
Symptom: As the widened gap rotates past the passive or active sensor, the signal drops out for a fraction of a millisecond. The EBCM interprets this sudden single-pulse dropout as rapid wheel lockup and triggers false ABS activation (pedal pulsation and grinding noise) during light braking just before the vehicle comes to a complete stop, typically without illuminating the ABS warning light or storing a hard DTC.
Chipped or Missing Teeth: Physical impact from road debris or careless prying during suspension repairs can chip or snap off reluctor teeth. A missing tooth causes a periodic signal drop once per wheel revolution, setting a wheel speed correlation code.
Debris Accumulation: Ferrous metal filings from brake pad wear can pack into the valleys between tone ring teeth. This magnetic debris bridges the gap, blurring the distinction between teeth and valleys, which severely attenuates sensor output voltage.
Inspection Techniques: Technicians must perform a thorough 360-degree visual inspection of the entire ring while slowly rotating the wheel assembly. Clean the ring with a wire brush to remove rust scales and metallic dust. Measure radial runout with a dial indicator mounted to the knuckle; runout exceeding 0.005 inches (0.13 mm) indicates a bent ring or damaged shaft. Lightly attempt to rotate the tone ring by hand; a cracked ring will spin freely on its mounting boss.
Magnetic Encoder Rings (Active Sensor Targets)
Modern light vehicles utilizing active 2-wire wheel speed sensors largely replace bulky steel reluctor rings with compact Magnetic Encoder Rings . Rather than relying on physical steel teeth, a magnetic encoder consists of a flat elastomeric (synthetic rubber) ring embedded with microscopic magnetic particles arranged into alternating North and South magnetic poles (typically 40 to 80 pole pairs around the circumference).
In most modern applications, this magnetic encoder ring is molded directly into the elastomeric inner grease seal of a press-in wheel bearing assembly or integrated into a bolt-on wheel hub unit.
Directional Wheel Bearing Installation Hazard: Because the magnetic encoder seal is integrated into only one side of a press-in wheel bearing assembly, the bearing is strictly directional .
If a technician presses the wheel bearing into the steering knuckle backward (with the magnetic encoder seal facing outward toward the wheel flange rather than inward toward the wheel speed sensor), the sensor will have no magnetic target to read.
Result: Upon driving the vehicle, the EBCM detects 0 mph from that wheel while the other three wheels report vehicle speed. The module immediately sets a hard C-series WSS DTC (e.g., C0035) and illuminates the ABS, TCS, and ESC warning lamps.
Diagnostic Inspection of Encoder Rings: Because magnetic poles embedded in a smooth rubber seal are completely invisible to the human eye, visual inspection alone cannot confirm encoder health or orientation. Technicians must use a specialized Magnetic Test Card (viewer film containing micro-encapsulated iron particles suspended in liquid).
Testing Procedure: Place the magnetic test card flat against the bearing seal. If the encoder is present and intact, the magnetic fields cause the iron particles to align, displaying a crisp, visible pattern of dark and light green radial stripes representing the North and South pole pairs.
Demagnetization Damage: Dropping a bearing, striking the bearing seal with a hammer, or exposing the seal to strong magnetic tools (such as magnetic pickup tools or welding equipment) will demagnetize or scramble the pole alignment. The magnetic test card will reveal smeared, missing, or irregular stripes in damaged areas, requiring complete bearing replacement.
Aftermarket Component Verification
When replacing CV axle assemblies, technicians must verify that the replacement shaft's tone ring tooth count matches the original equipment specification exactly. For example, installing an axle equipped with a 48-tooth tone ring on a vehicle whose EBCM is programmed for a 52-tooth ring will cause the EBCM to calculate a wheel speed that is roughly 8% slower than the remaining three wheels. This constant speed mismatch triggers immediate traction control and ABS correlation fault codes.