Study guide
7.2 Electric Cooling Fans, PWM Controls, Viscous Fan Clutches, Shrouds & Active Grille Shutters
ASE A7 Heating and Air Conditioning Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: ASE A7 Exam Fundamentals & Refrigeration Principles
1.1 ASE A7 Exam Overview & Certification Requirements 1.2 Thermodynamics & Automotive Refrigeration Cycle 1.3 Expansion Valve (TXV) vs. Fixed Orifice Tube (CCOT) Systems
2 Chapter 2: Refrigerants, Lubricants, Environmental Regulations & Safety
2.1 Refrigerants: R-12, R-134a, R-1234yf & Next-Gen Chemistry 2.2 Lubricants & System Compatibility (PAG, POE, Mineral) 2.3 EPA Section 609 Regulations, Recovery Cylinders & Shop Safety
3 Chapter 3: HVAC Performance Testing & Diagnostic Gauge Interpretation
3.1 Manifold Gauge Sets, Couplers & Operating Pressure Baselines 3.2 Pressure & Temperature Diagnostic Patterns (High/Low Scenarios) 3.3 Superheat & Subcooling Calculations in Mobile HVAC Diagnosis
4 Chapter 4: Leak Detection, Recovery, Evacuation & Charging Service
4.1 Leak Detection Methods (Electronic, UV Dye, Nitrogen, Vacuum Decay) 4.2 Refrigerant Recovery, System Flushing & Contaminant Inspection 4.3 Deep Evacuation (Micron Gauge) & Precision Recharging Procedures
5 Chapter 5: Refrigeration System Mechanical Components Diagnosis
5.1 A/C Compressors: Fixed, Variable Displacement & Electronic Control Valves 5.2 Compressor Clutch Diagnosis, Air Gap Shimming & Electrical Feed 5.3 Condensers, Parallel-Flow Technology & Subcooling Performance 5.4 Evaporator Cores, Accumulators & Receiver-Driers 5.5 Evaporator Freeze Protection: Cycling Switches, Temperature Sensors & EPR/POA Valves
6 Chapter 6: Metering Devices, Lines, Fittings & Air Distribution
6.1 Thermal Expansion Valves (TXV) & Fixed Orifice Tubes (FOT) Diagnosis 6.2 Refrigerant Lines, Barrier Hoses, Spring Lock Couplings & O-Rings 6.3 Cabin Air Filters, Case Sanitization & Airflow Distribution
7 Chapter 7: Engine Cooling System & Heating Diagnosis
7.1 Engine Cooling System: Radiator, Pressure Cap, Water Pump & Thermostat 7.2 Electric Cooling Fans, PWM Controls, Viscous Fan Clutches, Shrouds & Active Grille Shutters 7.3 Heater Core Diagnosis, Coolant Flow & Air Bleeding Procedures 7.4 Heater Control Valves, Auxiliary Coolant Pumps & Supplemental Heat (PTC, Thermoelectric, Seat & Wheel Heaters)
8 Chapter 8: Electrical Controls, Blower Circuits & Actuators
8.1 HVAC Electrical Fundamentals, Wiring Schematics & DMM/DSO Testing 8.2 Blower Motors, Resistor Packs & Electronic Power Modules 8.3 Blend, Mode & Recirculation Doors: Electric, Stepper, Vacuum Actuators & Control Cables
9 Chapter 9: Sensors, Switches & Electronic Climate Control
9.1 Temperature Sensors (In-Car, Ambient, Evaporator) & Sunload Photodiodes 9.2 Pressure Switches, Linear Transducers & Compressor Cutoff Logic 9.3 Automatic Temperature Control (ATC), Dual-Zone Systems & Scan Tool Diagnostics
10 Chapter 10: Hybrid/EV Thermal Management & Practical Diagnostic Scenarios
10.1 High-Voltage Electric Compressors, POE Oil & Hybrid/EV Safety 10.2 Heat Pump Systems & Battery Thermal Management Loops 10.3 ASE A7 Technician A / Technician B Diagnostic Scenarios & Troubleshooting Flowcharts
7.2 Electric Cooling Fans, PWM Controls, Viscous Fan Clutches, Shrouds & Active Grille Shutters
Key Takeaways Explain This Topic AI
An airflow-related complaint suggests tests of fans, controls, shrouds and heat-exchanger paths; road-speed improvement alone does not identify a failed part.
Series/parallel fan diagnosis requires the actual schematic. Equal motor voltages and particular relay fault effects cannot be assumed for every circuit.
PWM duty cycle describes the control waveform; its relationship to fan speed and its failure strategy are manufacturer-specific.
Keep clear of fans and shutters during operation or commanded tests. Do not hand-spin a hot engine’s fan or use objects to stop a running fan.
Verify actual fan response, airflow hardware and grille-shutter operation with the prescribed procedure before replacing a motor, module or clutch.
Last updated: October 2026
Airflow is a system result
Heat must leave the condenser and radiator through their air paths. Fans, shrouds, seals, air dams and active grille shutters help control that airflow. A spinning fan can still deliver inadequate airflow if blades, direction, shrouding or the heat-exchanger path are wrong. Conversely, an inactive fan may be consistent with the current command and operating conditions.
A complaint that improves at road speed makes airflow a useful investigation, but does not prove a particular fan fault. There is no universal speed below which ram airflow is zero or above which every fan switches off. Load, ambient conditions, vehicle aerodynamics and control strategy matter. Poor cooling at all speeds can still involve airflow; poor cooling only at high load can also involve coolant circulation or refrigerant-system faults.
Inspect under safe conditions before operating tests. Fans may run after ignition-off or start when a controller requests them. Secure the vehicle and use the required isolation before reaching into the fan area. Keep hands, clothing, probes and leads away from blades and shutter mechanisms during tests. Do not use a hand, newspaper or tool to arrest a running fan, or perform an improvised hand-spin test immediately after hot-engine shutdown.
Separate command, drive and response
Obtain the exact wiring diagram, control description and diagnostic procedure. Determine whether the system uses relay-switched motors, a separate electronic module, an integrated motor controller or an engine-driven clutch. Check the relevant sensor data for plausibility: a false coolant-temperature or refrigerant-pressure signal can produce an inappropriate cooling request.
Then compare the requested operation with measured response. Depending on the system, evidence may include scan-tool target speed, feedback speed, current, loaded power/ground checks and the actual control waveform. A valid command plus an unloaded battery-voltage reading is not enough to condemn a motor; a poor connection may fail only under load. An incorrect command is not automatically a failed engine controller, because inputs, wiring, network state and enable conditions must be checked.
A specified series/parallel example
Consider a teaching circuit with two brushed DC fan motors. Relay 1 feeds the positive side of Motor 1. A changeover relay connects Motor 1’s return either to Motor 2’s positive side in low mode, or to ground in high mode. Motor 2’s return is grounded. Relay 3 provides Motor 2’s positive supply in high mode. This defines the example’s circuit; it is not a universal three-relay pinout.
Mode in this stated circuit Current path What follows
Low Supply → Relay 1 → Motor 1 → changeover series contact → Motor 2 → ground The same current passes through both motors
High Motor 1 gets supply through Relay 1 and ground through the changeover contact; Motor 2 gets supply through Relay 3 Each motor has its own supply-to-ground path
Motor 1 internally open Low-mode series path is broken; Motor 2’s high-mode path remains intact Neither runs in low; Motor 2 can still run in high
Series operation does not guarantee exactly 6 V per motor on every 12 V vehicle. For an idealized 12.0 V example with negligible wiring/contact drops, the two motor drops sum to 12.0 V. Equal 6.0 V drops require additional symmetry; motor load and back electromotive force can differ. In a real running vehicle the supply itself need not be exactly 12.0 V.
Trace relay faults through the stated circuit. If the changeover relay remains on its series contact during high mode while both supply relays work, both terminals of Motor 1 are near supply potential. Its driving voltage is then near zero, while Motor 2 still has supply and ground. That fault does not, by itself, create a direct supply-to-ground short. Distinguish it from an internal motor open with the prescribed contact, voltage-drop and isolated motor tests; the symptom alone is not unique.
PWM and electronic modules
Pulse-width modulation (PWM) encodes a command through the proportion of a repeating cycle spent in a defined active state. For a hypothetical active-high waveform with a 10 ms period and 4 ms high time, duty cycle is 4/10 × 100 = 40% , and frequency is 1/0.010 = 100 Hz . This calculation describes the waveform, not necessarily 40% of maximum fan speed. The active polarity, valid range, frequency, command mapping and diagnostic default depend on the system. Some fans use network messages instead.
Pico’s automotive fan test compares control signals and current and emphasizes model variation. Use the applicable wiring and signal specifications, suitable instruments and approved connection methods. Do not apply battery voltage to a logic or network terminal. A fan running continuously at high speed may be commanded for real heat, respond to an input or communication fault, or have a control-stage fault. “Open PWM wire always means full speed” is not a universal diagnostic rule.
Thermal and electronically controlled viscous clutches
A thermal viscous clutch uses temperature-sensitive control of fluid in its working chamber to change torque transfer. It does not simply lock mechanically at one fixed temperature for every application. Startup engagement, release and response depend on the clutch and vehicle. Hayden’s thermal-clutch guidance specifically avoids publishing a universal face-temperature test because approaching that area can cause injury.
Use the OEM’s safe inspection and operating-response procedure, including any approved remote speed measurement and test conditions. Check blade condition, correct clutch application, drive, leaks and airflow obstructions. A universal number of hand-spun revolutions cannot establish internal fluid loss. Do not deliberately overheat an engine to create a test condition.
An electronically controlled viscous clutch uses a commanded actuator to regulate engagement and may provide speed feedback. Hayden’s EVC explanation identifies manufacturer-specific inputs and response. If actual speed misses a target, investigate the command, circuit, drive, feedback validity and prescribed response time before replacing the clutch. A duty-cycle percentage does not promise an identical percentage of shaft-speed coupling.
Shrouds, air dams and grille shutters
Inspect missing or damaged shrouds, seals, deflectors and debris between heat exchangers. These can divert air around the intended path. Use complaint conditions to prioritize checks, not to assign all idle complaints to shrouds and all highway complaints to air dams.
Active grille shutters adjust airflow and aerodynamic behavior under the vehicle’s control strategy. VDO’s component guidance identifies obstruction, collision damage, wiring and actuator faults, with failures possible in either open or closed positions. Do not assume every design springs open on power loss or uses the same communication protocol.
Inspect safely for binding and damage, then use the specified actuation and position-feedback tests while keeping clear. A successful sweep shows response during that test, not immunity from an intermittent fault under road load. Follow any required calibration after repair. Finally, verify cooling request, actual response and vehicle performance under the original complaint conditions without exceeding safe operating limits.