Study guide
3.4 No-Crank, No-Start, Battery, and Charging Diagnosis
ASE A9 Light Vehicle Diesel Engines Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 ASE Question Formats, Research Items, and Scoring 1.3 Independent Prep Strategy by Content Area Weight
2 Diagnostic Strategy, Scan Data, Inspection, and NVH
2.1 Complaint Verification, VIN, Engine ID, and Service Information 2.2 Scan Tool Data, Freeze Frame, DTCs, and Repair Verification 2.3 Leak Inspection and Engine Compartment Wiring 2.4 Engine Noise and Vibration Diagnosis
3 Smoke, Fuel Quality, Driveability, and Starting
3.1 Exhaust Smoke, Odor, Volume, and Crankcase Pressure 3.2 Fuel Quality, Contamination, Consumption, and Driveability Complaints 3.3 In-Bay Cooling and Lubrication Screening 3.4 No-Crank, No-Start, Battery, and Charging Diagnosis
4 Cylinder Head and Valve Train Diagnosis and Repair
4.1 Cylinder Head Inspection, Thickness, Warpage, Cracks, and Passages 4.2 Valves, Guides, Seats, Springs, Retainers, Locks, and Seals 4.3 Injector/Glow Plug Sleeves, Bridges, Head Gasket Thickness, and TTY Installation 4.4 Valve Train, Lash, Overhead Cam, and Timing Drive
5 Engine Block Diagnosis and Repair
5.1 Pans, Covers, Block Inspection, Deck Height, and Cylinder Walls 5.2 In-Block Camshaft, Crankshaft, Select-Fit Bearings, and End Play 5.3 Pistons, Pins, Rings, Protrusion, and Cooling Jets 5.4 Drive Gear Train, Vibration Damper, Flywheel, Flexplate, and Dual-Mass Flywheel
6 Lubrication Systems Diagnosis and Repair
6.1 Oil Pressure, Sensors, Pump, Screens, and Pressure Regulator 6.2 Oil Cooler, Turbo Lubrication, Filters, and Oil Specification
7 Cooling Systems and Accessory Drive
7.1 Drive Belts, Pulleys, Tensioners, and Alignment 7.2 Thermostats, Water Pump, Coolant Type, Flush, and Bleed 7.3 Radiator, Cap, Pressure Test, Fan, Clutch, Controls, and Shroud
8 Air Induction and Turbocharging
8.1 Air Cleaner, Induction Piping, and Restrictions 8.2 Charge Air Cooler, Piping, and Intake Manifold Pressure Tests 8.3 Turbochargers, Wastegates, and Boost Control 8.4 Variable Geometry Turbochargers and Actuators
9 Exhaust Flow, Glow Plugs, DOC, and DPF
9.1 Intake Manifolds, Exhaust Backpressure, Temperature, and Exhaust Hardware 9.2 Glow Plugs and Inlet Air Heaters 9.3 Diesel Oxidation Catalyst, DPF, and Regeneration
10 SCR, EGR, Throttle Valves, and Crankcase Ventilation
10.1 SCR, Diesel Exhaust Fluid, and NOx Control 10.2 EGR Valves, Coolers, Bypass, Sensors, and Wiring 10.3 Diesel Throttle Valves and Crankcase Ventilation
11 Low-Pressure Fuel Supply
11.1 Fuel Tanks, Vents, Caps, Supply/Return Lines, and Fittings 11.2 Transfer Pump, Water Separators, Filters, Heaters, and Coolers 11.3 Air in Fuel, Priming, Bleeding, and Low-Pressure Regulation
12 High-Pressure Common Rail Fuel Systems
12.1 High-Pressure Lines, Fittings, Seals, Transfer Tubes, and Safety 12.2 Common-Rail Pump, Rail, and Pressure Control 12.3 Common-Rail Injectors, Back-Leakage, and Replacement
13 HEUI, PLN-E, and EUI Fuel Systems
13.1 Hydraulic Electronic Unit Injector (HEUI) Systems 13.2 Pump-Line-Nozzle Electronic and Electronic Unit Injector Systems
14 Fuel Electronics, Scan Diagnosis, and Interrelated Systems
14.1 Injector Calibration Codes, Software Updates, and Control-Module Relearn 14.2 Harnesses, Sensors, Actuators, and DMM Voltage-Drop Testing 14.3 Interrelated Systems, Electronic Throttle, and PTO Controls
3.4 No-Crank, No-Start, Battery, and Charging Diagnosis
Key Takeaways Explain This Topic AI
Split the complaint: no-crank, cranks but will not start, hard start, or starts then dies—each has a different first test.
Diesel cranking current is high; measure voltage drop at the starter during crank and compare CCA and state of charge, not just a 12.6 V key-off reading.
Crank-no-start on common-rail engines needs rail pressure, CKP/CMP sync, and heat (glow plugs or grid heater) plus compression; do not skip any leg.
Key-off drain and poor connections create the same no-crank as a dead cell; prove parasitic current and cable drops before you replace a starter.
Undercharge, overcharge, or no-charge causes glow-plug, injector-driver, and module faults that look like fuel or sensor failures.
Last updated: September 2026
3.4 No-Crank, No-Start, Battery, and Charging Diagnosis
Quick Answer: Decide whether the engine cranks . If it does not, stay on battery, cables, starter enable, and a seized crank. If it cranks, prove glow / grid heat , compression , rail pressure , and crankshaft / camshaft sensor (CKP/CMP) sync. Then prove the batteries can deliver diesel cranking current and that the charging system is not undercharging, overcharging, or dead—because low voltage makes diesel modules lie.
Name the starting complaint
The task list splits four behaviors. Mixing them wastes hours.
No-cranking: starter does not turn the engine, or turns so slowly the rail pump never spins.
Cranks but fails to start: starter RPM is adequate; combustion never catches.
Hard starting: eventually runs, but only after long crank, especially cold.
Starts but does not continue to run: fires then dies—fuel enable, air in fuel, or inducement/security.
A 6.7 Cummins with a grid heater that never warms can crank-no-start at 10°F and start in 20 seconds at 70°F. That is hard start / cold no-start, not a dead battery, if cranking voltage is sound.
No-crank first
Verify shift interlock (Park/Neutral or clutch) and starter-enable from the ECM or relay. Then measure.
Light-duty diesels, especially dual-battery Super Duty and Ram 2500/3500, draw hundreds of amps during crank. A battery that reads 12.6 V key-off can still fall to 8 V at the starter stud while cranking. Typical screening: resting voltage per battery, cold cranking amps (CCA) versus the published group size, and voltage drop on the positive cable and the ground path during crank . Many diesel procedures want to see cranking voltage stay near or above about 9.6–10.0 V at the starter (OEM spec wins). A 0.5 V drop on the cable plus 0.5 V on the ground is already a connection fault, not a new starter.
Seized engine: if voltage stays high and the starter only clicks or stalls instantly, the engine may not rotate (hydrolock from a leaking injector or EGR coolant fill, or a mechanical lock). Do not keep hammering the starter.
Crank, no-start: four legs
Once the engine spins at a diesel cranking speed (often a few hundred rpm; use the OEM number):
Heat. Glow plugs (Power Stroke, Duramax, EcoDiesel, TDI) or a grid heater / inlet air heater (Cummins 6.7). Command wait-to-start, measure glow current or heater voltage drop, and do not skip a failed glow module because rail pressure looks pretty. Ceramic glow plugs on later engines are not 12 V bulbs; follow the diagram.
Compression. Relative compression with a current probe, or a mechanical compression test when service information allows (diesel pressures are high; use the right tester). A jumped timing chain or a spun cam on a 6.7 Power Stroke cranks forever with good rail pressure.
Rail pressure. Common-rail engines need a minimum cranking mega-pascal (MPa) or psi rail value before injectors will fire. No rail: lift pump, plugged filter, air in the supply, failed high-pressure pump, or a pressure-control valve stuck open. Scan actual versus minimum for start.
CKP/CMP sync. No rpm on the scan tool while the starter sounds healthy is a CKP problem. rpm with no cam sync can be a CMP or a tone-wheel issue. Immobilizer that withholds injector drivers looks like no-start with rpm present and rail collapsing or never being used.
Hard start that is only cold is heat, cetane, gelled fuel, or borderline compression. Hard start that is only hot can be vapor, a failing CKP, or injector leak-down washing the cylinder (white smoke and a fuel-smelling dipstick after several no-starts).
Starts-then-dies: watch injector command and rail as it dies. Security fuel cutoff, a transfer pump that primes then overheats, air drawn at a cracked suction line, or aftertreatment inducement that allows one start then shuts down are different scan pictures.
Complaint First proof Common light-duty miss
No-crank Voltage drop during crank, enable, rotate-by-hand if needed Dual batteries, one dead, hidden in parallel
- Crank, no-start Rail, rpm/sync, glow or grid, compression Replacing injectors with 8.5 V cranking
- Hard start cold Heat system and fuel quality Ignoring wait-to-start lamp logic
- Starts, then dies Injector enable, suction air, inducement Calling it a bad ECM without security data
- Battery condition, connections, key-off drain
Condition: load test or conductance tester each battery. Dual-battery trays hide one sulfated battery that drags the other down. Connections: clean the open-box terminals, the case ground, and the engine block stud. A painted ground on a frame-mounted battery tray is a classic Ram no-crank.
Excessive key-off drain (parasitic draw) is a starting complaint that happens overnight. After modules sleep (often 20–45 minutes; use OEM), measure current in series with the negative cable. Compare to the published key-off budget. Glow-plug modules, aftertreatment heaters, and failed inverter circuits on pickups can pull several amps all night. A drain that kills batteries also causes the next morning's crank-no-start because rail and glow never see 12 V.
Do not disconnect batteries on a networked diesel to hunt a drain without a memory-saver plan and a note that radio/security/TPMS learns may reset; still, you must find the drain if overnight death is the complaint.
Charging: undercharge, overcharge, no-charge
Running voltage at the batteries should sit in the OEM charging window—often about 13.8–14.8 V with the diesel running and electrical load applied, but the service information number is the spec. Three faults create engine complaints that look like sensors and fuel:
No-charge: belt, pulley, alternator, or a load-dump fuse. Voltage sags toward battery rest. Glow cycles fail, injector drivers glitch, the ECM resets, and you get false CKP/CMP codes.
Undercharge: a weak alternator that holds 13.0 V at idle with fans and grid-heater after-run still pulling. Headlights dim, wait-to-start extends, and a dual-battery bank never recovers after a cold start.
Overcharge: regulator failed high (15.5–17 V). Batteries boil, acid smell, swollen cases, and modules go erratic—cluster, glow controller, fuel-pump driver. Overcharge can look like a no-start after a short drive because a flooded battery then fails a crank.
Charging diagnosis during general diagnosis is a running voltage and ripple screen plus belt inspection—not a full bench of the alternator unless the screen fails. If voltage is 16 V and the truck has random injector codes, fix charge voltage before you code injectors.
Worked example. A 2020 Ram 3500 6.7 Cummins cranks slowly at 20°F and will not start. Resting voltage is 12.4 V. During crank the starter B+ is 8.2 V; battery post is 10.8 V. Glow relay never sees a solid 12 V. Grid heater is innocent until the cable drop is repaired. After cables and a failed left-tray battery are corrected, cranking is 10.4 V and the grid heater is allowed to run; the truck starts. That is battery and connection diagnosis causing a crank-no-start, not a high-pressure pump.