Study guide
3.1 Exhaust Smoke, Odor, Volume, and Crankcase Pressure
ASE A9 Light Vehicle Diesel Engines Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 ASE Question Formats, Research Items, and Scoring 1.3 Independent Prep Strategy by Content Area Weight
2 Diagnostic Strategy, Scan Data, Inspection, and NVH
2.1 Complaint Verification, VIN, Engine ID, and Service Information 2.2 Scan Tool Data, Freeze Frame, DTCs, and Repair Verification 2.3 Leak Inspection and Engine Compartment Wiring 2.4 Engine Noise and Vibration Diagnosis
3 Smoke, Fuel Quality, Driveability, and Starting
3.1 Exhaust Smoke, Odor, Volume, and Crankcase Pressure 3.2 Fuel Quality, Contamination, Consumption, and Driveability Complaints 3.3 In-Bay Cooling and Lubrication Screening 3.4 No-Crank, No-Start, Battery, and Charging Diagnosis
4 Cylinder Head and Valve Train Diagnosis and Repair
4.1 Cylinder Head Inspection, Thickness, Warpage, Cracks, and Passages 4.2 Valves, Guides, Seats, Springs, Retainers, Locks, and Seals 4.3 Injector/Glow Plug Sleeves, Bridges, Head Gasket Thickness, and TTY Installation 4.4 Valve Train, Lash, Overhead Cam, and Timing Drive
5 Engine Block Diagnosis and Repair
5.1 Pans, Covers, Block Inspection, Deck Height, and Cylinder Walls 5.2 In-Block Camshaft, Crankshaft, Select-Fit Bearings, and End Play 5.3 Pistons, Pins, Rings, Protrusion, and Cooling Jets 5.4 Drive Gear Train, Vibration Damper, Flywheel, Flexplate, and Dual-Mass Flywheel
6 Lubrication Systems Diagnosis and Repair
6.1 Oil Pressure, Sensors, Pump, Screens, and Pressure Regulator 6.2 Oil Cooler, Turbo Lubrication, Filters, and Oil Specification
7 Cooling Systems and Accessory Drive
7.1 Drive Belts, Pulleys, Tensioners, and Alignment 7.2 Thermostats, Water Pump, Coolant Type, Flush, and Bleed 7.3 Radiator, Cap, Pressure Test, Fan, Clutch, Controls, and Shroud
8 Air Induction and Turbocharging
8.1 Air Cleaner, Induction Piping, and Restrictions 8.2 Charge Air Cooler, Piping, and Intake Manifold Pressure Tests 8.3 Turbochargers, Wastegates, and Boost Control 8.4 Variable Geometry Turbochargers and Actuators
9 Exhaust Flow, Glow Plugs, DOC, and DPF
9.1 Intake Manifolds, Exhaust Backpressure, Temperature, and Exhaust Hardware 9.2 Glow Plugs and Inlet Air Heaters 9.3 Diesel Oxidation Catalyst, DPF, and Regeneration
10 SCR, EGR, Throttle Valves, and Crankcase Ventilation
10.1 SCR, Diesel Exhaust Fluid, and NOx Control 10.2 EGR Valves, Coolers, Bypass, Sensors, and Wiring 10.3 Diesel Throttle Valves and Crankcase Ventilation
11 Low-Pressure Fuel Supply
11.1 Fuel Tanks, Vents, Caps, Supply/Return Lines, and Fittings 11.2 Transfer Pump, Water Separators, Filters, Heaters, and Coolers 11.3 Air in Fuel, Priming, Bleeding, and Low-Pressure Regulation
12 High-Pressure Common Rail Fuel Systems
12.1 High-Pressure Lines, Fittings, Seals, Transfer Tubes, and Safety 12.2 Common-Rail Pump, Rail, and Pressure Control 12.3 Common-Rail Injectors, Back-Leakage, and Replacement
13 HEUI, PLN-E, and EUI Fuel Systems
13.1 Hydraulic Electronic Unit Injector (HEUI) Systems 13.2 Pump-Line-Nozzle Electronic and Electronic Unit Injector Systems
14 Fuel Electronics, Scan Diagnosis, and Interrelated Systems
14.1 Injector Calibration Codes, Software Updates, and Control-Module Relearn 14.2 Harnesses, Sensors, Actuators, and DMM Voltage-Drop Testing 14.3 Interrelated Systems, Electronic Throttle, and PTO Controls
3.1 Exhaust Smoke, Odor, Volume, and Crankcase Pressure
Key Takeaways Explain This Topic AI
Black smoke is soot from excess fuel or insufficient air; confirm color at idle and under load, not from one cold parking-lot puff.
Blue smoke is oil from rings, a turbocharger seal, valve stem seals, or CCV pull-over; oily charge-air cooler piping points at the compressor-side turbo seal.
Fuel-smelling white smoke is unburned diesel and is worst cold; sweet white smoke is coolant from a head gasket, cracked head, or EGR cooler and often worsens when warm.
Exhaust odor is a separate check: raw fuel, coolant, burning oil, DEF/ammonia, and melting wiring are different findings.
A crankcase pressure test with a low-range gauge or manometer separates ring blow-by from a stuck CCV/CDR and from boost packing into the turbo oil drain.
Last updated: September 2026
3.1 Exhaust Smoke, Odor, Volume, and Crankcase Pressure
Quick Answer: Color names the contaminant, odor confirms it, and volume plus load tell you when it happens. Black is excess fuel or insufficient air. Blue is oil. Fuel-smelling white is unburned diesel; sweet white is coolant. Measure crankcase pressure before you condemn rings, a turbocharger, or a valve cover gasket.
Smoke is a running combustion report
On a light-duty diesel—Ford 6.7 L Power Stroke , GM 6.6 L Duramax , Ram 6.7 L Cummins , Jeep/Ram 3.0 L EcoDiesel , or VW 2.0 TDI —the tailpipe is one of the few live reports you get without a scan tool. During general diagnosis you check exhaust for abnormal odor , color , and volume , then you perform a crankcase pressure test . Those checks belong in the same bay visit because oil, fuel, and coolant can each leave the engine through the exhaust, the crankcase, or both.
Do not diagnose from one cold idle puff in the parking lot. A Duramax that idles clean and then rolls a black cloud on a 3–4 gear pull is not the same engine as a TDI that idles in a constant blue haze. Condition of test—cold versus hot, idle versus load, acceleration versus deceleration—is part of the finding, not a footnote.
Black smoke: excess fuel or not enough air
Black smoke is soot: carbon that never found enough oxygen. The mixture in that cylinder was rich relative to the air that actually arrived.
Typical light-duty causes include:
A restricted air filter, snow-packed snorkel, or collapsed intake hose
A charge-air cooler (CAC) boot leak or disconnected pipe ( boost leak ): the engine control module (ECM) fuels for a boost or mass-air target the engine never received
- Underboost from a weak turbocharger , stuck variable-geometry turbocharger (VGT) vanes, or a seized vane ring
- Stuck-open exhaust gas recirculation (EGR) flooding the cylinder with inert gas
- A leaking or stuck-open common-rail injector
On some trucks, a diesel particulate filter (DPF) so loaded that the ECM derates while the driver still reports smoke on hard acceleration before a successful regeneration (regen)
Idle-only black often points to EGR or a dripping injector at low rail pressure. Load-only black points to missing air (boost/CAC) or an injector that overfuels as pulse width grows. Do not skip the air path because commanded fuel on the scan tool looks normal.
Blue smoke: oil in the burn
Blue smoke is lubricating oil reaching the chamber or the exhaust stream.
Worn rings or glazed walls—common on trucks that idle in lots and never get a hot highway run
Turbocharger oil seals: a compressor-side leak oils the intake, the CAC, and then the cylinders; a turbine-side leak oils the downpipe. Oily CAC piping is a compressor-seal clue, not a valve-cover clue
Valve stem seals and guides—often worst on deceleration when a diesel throttle valve or falling manifold pressure pulls oil down the guides
An overfilled crankcase, including fuel dilution that raises the level, so closed crankcase ventilation (CCV) pulls oil into the intake
A thin idle-only blue that clears with rpm can still be a turbo seal at low shaft speed. Continuous blue under load is more often rings or a severe turbo leak.
White smoke: fuel versus coolant
White smoke is the color that fools people. Split it with odor and temperature, not with a single glance.
Fuel-smelling white or gray-white is unburned diesel vapor. It is worst when the engine is cold and should fade as combustion temperature rises. Causes include failed glow plugs or a failed glow-plug control module, a failed grid heater / inlet air heater (a common 6.7 L Cummins pattern), late injection timing, low compression, or a cylinder that is not firing. A 6.7 Cummins that white-smokes down the block after a no-heat cold start is a combustion-temperature problem until you prove otherwise.
Sweet-smelling white is coolant. Sources include a leaking head gasket, a cracked cylinder head, or an EGR cooler dumping coolant into the intake or exhaust. EcoDiesel and 6.7 Power Stroke EGR cooler failures often show sweet white that worsens as the engine warms —the opposite of cold fuel white. Confirm with coolant level, a cooling-system pressure test, and a combustion-gas-in-coolant check. Do not stop at color.
Gray that will not commit is often mixed oil plus incomplete burn, or hydrocarbons from a failed regen saturating the diesel oxidation catalyst (DOC) . Describe what you see; do not invent a fourth official color.
- Appearance Dominant source When it is worst Odor
- Black Excess fuel or insufficient air Often under load Sharp, sooty diesel
- Blue Engine or turbo oil Idle, load, or deceleration depending on path Burning oil
- White, fuel Unburned diesel Cold; should clear hot Raw fuel
- White, coolant Coolant in combustion or EGR Often worse fully warm Sweet antifreeze
- Volume, load, and aftertreatment masking
Volume is how much mass is leaving. A wisp that vanishes at 1,500 rpm is not a highway plume. Snap-throttle in park is not a load test. If the complaint is highway smoke, use a loaded stall only if service information allows it, or road-test with a helper watching the tailpipe.
A soot-loaded DPF can make the tailpipe look cleaner than engine-out exhaust. If a pre-DPF joint is accessible, compare. Exhaust temperature and DPF differential pressure on the scan tool tell you whether the filter is hiding soot or contributing to the complaint. Hydrocarbon odor with little visible smoke can still mean a dosing valve is wetting the DOC during a failed regen.
Exhaust odor as its own check
Odor is not a restatement of color.
Raw fuel: injector leak-down, a no-fire cylinder, late timing, or a leaking hydrocarbon doser used for regen on some Power Stroke and Duramax systems
- Sweet coolant: EGR cooler or head gasket
- Burning oil: turbo, rings, or CCV pull-over
Ammonia, urea, or diesel exhaust fluid (DEF) : overdosing, a leaking DEF injector, or crystallization at the selective catalytic reduction (SCR) mixer—this is not coolant
Rotten sulfur: uncommon on ultra-low sulfur diesel (ULSD) at 15 ppm sulfur; think rich combustion or a saturated DOC, not 1990s high-sulfur fuel
Melting plastic or wiring: a harness on a hot turbo or EGR valve—report it even though it is not a combustion odor
Waft the plume. Do not put your face in the tailpipe.
Crankcase pressure test
A crankcase pressure test asks two questions: how much combustion gas is blowing by the rings, and can the ventilation system handle it? Light-duty diesels use CCV or a crankcase depression regulator (CDR) . A healthy system holds the crankcase near zero or slightly negative. Positive pressure that climbs with rpm is the problem.
High blow-by drives oil out the dipstick, rocker cover, and CCV, then into the intake as blue smoke. A stuck-closed CCV or CDR makes every gasket look like a leak; the valve cover is often a victim. A turbo oil drain packed with sludge, or a seal that lets boost into the drain, pressurizes the crankcase even with good rings.
Bay method
Follow the OEM procedure. A typical sequence:
Bring the engine to operating temperature.
Open a specified port (oil fill or a dedicated fitting). Guessing on a sealed system is not a test.
Connect a low-range gauge, manometer (inches of water), or blow-by meter.
Record idle and a specified higher rpm. Some Ford and Cummins procedures use a hose from the oil fill to a slack bag as a screen, then a gauge for a number.
Test both with CCV/CDR connected and, if directed, with it open or bypassed.
- Result First direction
- Slight vacuum or near zero with CCV on Ventilation doing its job
- High pressure with CCV on, low with CCV open Restricted separator, frozen or sludged CCV, stuck CDR
- High pressure even with CCV open Ring blow-by, a cylinder not sealing, or boost packed into the turbo drain
- Pressure that jumps when boost rises Turbo seal or oil-drain packing feeding the crankcase
Oil out of the fill cap with a normal reading on an open crankcase Look at level, dilution, and separator before a short-block estimate
A grocery-bag fill-rate check is a screen, not a specification. Use it to decide whether to connect a manometer.
Traps and a worked example
Overfilled oil, including fuel dilution from regen or injector leak-down, throws oil into the separator and mimics blow-by. A dirty air filter changes CCV flow. Do not import gasoline positive crankcase ventilation (PCV) names onto diesel CDR hardware. On 6.7 Power Stroke and some Duramax engines, a failed CCV separator dumps oil into the intake—blue smoke plus a wet CAC.
Worked example. A 2015 Ram 2500 6.7 Cummins weeps oil at the valley. Idle exhaust is clean; under load the tailpipe is light blue. Crankcase at idle with CCV connected reads +4 in. H2O and climbs at 2,000 rpm. Opening the CCV drops the reading. Start at the CCV/CDR and separator. If pressure stayed high with the CCV open, next tests are relative compression and the turbo drain—not a valve-cover gasket set.