Study guide

5.4 Drive Gear Train, Vibration Damper, Flywheel, Flexplate, and Dual-Mass Flywheel

ASE A9 Light Vehicle Diesel Engines Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 ASE Question Formats, Research Items, and Scoring 1.3 Independent Prep Strategy by Content Area Weight

2 Diagnostic Strategy, Scan Data, Inspection, and NVH

2.1 Complaint Verification, VIN, Engine ID, and Service Information 2.2 Scan Tool Data, Freeze Frame, DTCs, and Repair Verification 2.3 Leak Inspection and Engine Compartment Wiring 2.4 Engine Noise and Vibration Diagnosis

3 Smoke, Fuel Quality, Driveability, and Starting

3.1 Exhaust Smoke, Odor, Volume, and Crankcase Pressure 3.2 Fuel Quality, Contamination, Consumption, and Driveability Complaints 3.3 In-Bay Cooling and Lubrication Screening 3.4 No-Crank, No-Start, Battery, and Charging Diagnosis

4 Cylinder Head and Valve Train Diagnosis and Repair

4.1 Cylinder Head Inspection, Thickness, Warpage, Cracks, and Passages 4.2 Valves, Guides, Seats, Springs, Retainers, Locks, and Seals 4.3 Injector/Glow Plug Sleeves, Bridges, Head Gasket Thickness, and TTY Installation 4.4 Valve Train, Lash, Overhead Cam, and Timing Drive

5 Engine Block Diagnosis and Repair

5.1 Pans, Covers, Block Inspection, Deck Height, and Cylinder Walls 5.2 In-Block Camshaft, Crankshaft, Select-Fit Bearings, and End Play 5.3 Pistons, Pins, Rings, Protrusion, and Cooling Jets 5.4 Drive Gear Train, Vibration Damper, Flywheel, Flexplate, and Dual-Mass Flywheel

6 Lubrication Systems Diagnosis and Repair

6.1 Oil Pressure, Sensors, Pump, Screens, and Pressure Regulator 6.2 Oil Cooler, Turbo Lubrication, Filters, and Oil Specification

7 Cooling Systems and Accessory Drive

7.1 Drive Belts, Pulleys, Tensioners, and Alignment 7.2 Thermostats, Water Pump, Coolant Type, Flush, and Bleed 7.3 Radiator, Cap, Pressure Test, Fan, Clutch, Controls, and Shroud

8 Air Induction and Turbocharging

8.1 Air Cleaner, Induction Piping, and Restrictions 8.2 Charge Air Cooler, Piping, and Intake Manifold Pressure Tests 8.3 Turbochargers, Wastegates, and Boost Control 8.4 Variable Geometry Turbochargers and Actuators

9 Exhaust Flow, Glow Plugs, DOC, and DPF

9.1 Intake Manifolds, Exhaust Backpressure, Temperature, and Exhaust Hardware 9.2 Glow Plugs and Inlet Air Heaters 9.3 Diesel Oxidation Catalyst, DPF, and Regeneration

10 SCR, EGR, Throttle Valves, and Crankcase Ventilation

10.1 SCR, Diesel Exhaust Fluid, and NOx Control 10.2 EGR Valves, Coolers, Bypass, Sensors, and Wiring 10.3 Diesel Throttle Valves and Crankcase Ventilation

11 Low-Pressure Fuel Supply

11.1 Fuel Tanks, Vents, Caps, Supply/Return Lines, and Fittings 11.2 Transfer Pump, Water Separators, Filters, Heaters, and Coolers 11.3 Air in Fuel, Priming, Bleeding, and Low-Pressure Regulation

12 High-Pressure Common Rail Fuel Systems

12.1 High-Pressure Lines, Fittings, Seals, Transfer Tubes, and Safety 12.2 Common-Rail Pump, Rail, and Pressure Control 12.3 Common-Rail Injectors, Back-Leakage, and Replacement

13 HEUI, PLN-E, and EUI Fuel Systems

13.1 Hydraulic Electronic Unit Injector (HEUI) Systems 13.2 Pump-Line-Nozzle Electronic and Electronic Unit Injector Systems

14 Fuel Electronics, Scan Diagnosis, and Interrelated Systems

14.1 Injector Calibration Codes, Software Updates, and Control-Module Relearn 14.2 Harnesses, Sensors, Actuators, and DMM Voltage-Drop Testing 14.3 Interrelated Systems, Electronic Throttle, and PTO Controls

5.4 Drive Gear Train, Vibration Damper, Flywheel, Flexplate, and Dual-Mass Flywheel

Key Takeaways Explain This Topic AI

Inspect, replace, verify, and adjust the cam/crank drive as a gear train, chain, or belt depending on the engine: front gears on 6.7 Cummins and Duramax, a rear gear train on the 6.7 Power Stroke, chain on EcoDiesel, belt on many TDI engines.

A stretched timing chain rattles on cold start, retards cam timing, and sets cam/crank correlation codes; gears are checked for backlash, teeth, keys, and pump-drive condition.

Inspect the crankshaft vibration damper for elastomer cracks, oil swell, and a spun inertia ring that moves TDC marks; replace a failed damper as an assembly.

Inspect flywheels, flexplates, and dual-mass flywheels (EcoDiesel, some TDI, some Cummins) including the ring gear and mounting surfaces for cracks, wear, and runout; do not resurface a dual-mass unit like a conventional flywheel.

Independent ExamFinch teaching covers published A9 gear-train, damper, and flywheel tasks; it is not an ASE-required course.

Last updated: September 2026

Drive gear train: gears, chains, and belts on light-duty diesels

“ Drive gear train ” on A9 means whatever turns the camshaft (and often the injection pump or high-pressure pump) from the crankshaft: gears , a chain , or a belt . Match the hardware to the engine before you look for a rubber belt on a Cummins or a rear gear set on a TDI.

This section is independent ExamFinch teaching of published A9 gear-train, damper, and flywheel skills. It is not an ASE course and not a claim of official approval.

Engine family Typical cam drive What you inspect

Ram 6.7 Cummins Front gear train (cam-in-block) Gear teeth, backlash, keys/dowels, injection-pump drive gear, front gear-housing and cover seals

Duramax Front gears (cam-in-block) Crank and cam gears, backlash, keyways, front cover

6.7 Power Stroke Rear gear train at the flywheel end (cam-in-block) Gear teeth, high-pressure pump drive gear, rear cover and seals; the damper-hub wear ring is a separate front-cover item

3.0 EcoDiesel Timing chain , guides, tensioner (OHC) Stretch, guide wear, tensioner leak-down, correlation codes

  • Many 2.0 TDI Timing belt (some later designs differ) Interval, teeth, tensioner, water-pump wear, jumped time
  • Ford 3.0 Power Stroke (F-150) Chain Same stretch and correlation path as other light-duty chains
  • Gears: inspect, replace, verify, adjust

On a 6.7 Cummins , the cam is driven from the front of the crank behind a gear housing and cover, the same end GM uses on the Duramax. The 6.7 Power Stroke is the light-duty engine that puts its gear train at the rear , under a cover at the flywheel end, where those gears also drive the high-pressure fuel pump. That layout surprises technicians who pull a front cover on every diesel. Open either housing only with the engine timed and locked per OEM tools when required. Inspect:

Tooth face pitting, step wear, and cracked hubs

Backlash with a dial indicator on a tooth, compared to spec (too little binds and whines; too much hammers and walks timing)

Keys, keyways, and dowel pins that locate injection-pump or cam gears

High-pressure pump drive gears (CP3-style gears on many Cummins/Duramax applications). Metal from a failing pump gear contaminates the front or rear cover and the bearings you just measured.

Verify timing marks or pin-lock positions after install. Adjust only where the OEM provides an adjustable gear or a specified backlash shim. Do not “advance it a tooth for more power.” On a diesel, one tooth is a no-start or a piston-to-valve event on OHC designs, and a severe timing error on cam-in-block designs.

Cummins and Duramax front gears and the Power Stroke rear gears all get the same tooth, backlash, and key or press-fit inspection. A 6.7 Power Stroke crank gear that has slipped on the crankshaft is a rear-housing repair; a damaged damper hub at the front of that same crank is a separate seal-and-wear-ring job.

Chains: stretched timing chain symptoms

A stretched timing chain on a 3.0 EcoDiesel (Jeep Grand Cherokee, Ram 1500) or a chain-driven Ford 3.0 diesel does not look like a Cummins front-gear rattle.

Symptoms to inspect for:

  • Cold-start rattle from the front cover that quiets as oil fills the tensioner
  • Cam/crank correlation diagnostic trouble codes and retarded cam timing on the scan tool
  • Hard start, rough idle, and low compression feel that is actually late valve events
  • Metal in the front cover from chewed guides
  • A tensioner that has leaked down or a guide that is worn to the aluminum

Replace the chain, guides, and tensioner as a set when stretch is confirmed. Measure chain stretch with the OEM gauge or by cam-to-crank degree error—do not “just tighten the tensioner.” Verify timing after install with marks or a scan-tool correlation test, then run until oil pressure fills the tensioner and recheck noise.

Belts: TDI interval service is gear-train work

Many U.S. 2.0 TDI engines use a timing belt . Inspect for cracked backs, oil soak from a leaking cam or water-pump seal, missing teeth, and a seized tensioner or idler. Replace at the published interval even if the belt “looks fine”—a jumped or broken TDI belt can destroy valves on an interference OHC diesel. When the belt is off, inspect the water pump and idlers; they are part of the same drive. Verify cover installation so the belt cannot rub.

Traps: looking for a TDI belt on a 6.7 Cummins; pulling a front cover on a 6.7 Power Stroke whose gear train is at the rear; ignoring gear backlash; calling every front-cover rattle a dual-mass flywheel; not locking an OHC diesel before chain or belt removal.

Crankshaft vibration damper

The crankshaft vibration damper (harmonic balancer) sits on the snout and controls torsional vibration. Light-duty diesels almost all use an elastomer (rubber) damper: a hub, a rubber ring, and an inertia mass. Some applications use a viscous damper (fluid inertia). Inspect it whenever the front cover, belt, or crank seal is off—and whenever a customer reports a new “whoosh” or a timing mark that “moved.”

Elastomer failure modes:

Rubber cracked, chunked, or oil-swollen. Oil-soaked rubber from a front seal leak accelerates failure. Chunks missing mean the inertia ring is no longer bonded.

Spun inertia ring versus the hub. The outer ring slips on the rubber. TDC marks, degree marks, and crank sensor windows on the ring are now false. Timing a 6.7 Power Stroke or Duramax to a spun damper mark puts the engine out of time even if the gears are correct. Replace the damper as an assembly; you cannot “re-index” the rubber in the bay.

Wobble / runout. A separated damper wobbles and wrecks the front seal and wear ring. Measure runout if the OEM gives a spec; replace if the rubber has shifted.

A viscous damper that weeps fluid or is seized internally is also a replace-as-an-assembly part. Do not try to refill it.

Worked example: a Duramax with a front seal leak, a shiny displaced rubber line, and a timing notch that no longer matches the hub keyway is a spun elastomer damper . Installing a new seal on that hub without replacing the damper repeats the leak and falsifies TDC.

Flywheel, flexplate, and dual-mass flywheel

Inspect the flywheel (manual or dual-mass) or flexplate (automatic) and the ring gear , plus the crank mounting surface , whenever the transmission is out or a starter-grind, vibration, or clutch complaint exists.

Conventional flywheel and flexplate

Cracks at the crank bolt circle, around dowels, and at the ring-gear weld. A cracked flexplate on a 6.7 Power Stroke or Duramax automatic often clicks at starter engagement and can set crank-sensor faults if the reluctor is flexplate-mounted.

Wear on the clutch friction surface (hot spots, scoring, glazed heat) and on the torque-converter pilots.

Ring gear teeth: starter pinion wear, missing teeth in one arc (the engine always stops in a similar position), and heat from a slipping starter.

Runout of the flywheel or flexplate face and of the ring-gear OD, measured with a dial indicator on a fixed crank. Excessive runout is a crank flange burr, a missing dowel, or a bent flexplate—not “just torque the bolts more.”

Mounting surfaces: raised metal around crank holes, elongated holes, and a converter that was installed on the wrong flexplate spacer.

A conventional single-mass flywheel can often be resurfaced to OEM min thickness. A flexplate is not machined; it is replaced if cracked or warped.

Dual-mass flywheel (DMF)

A dual-mass flywheel uses two plates, arc springs (or similar dampers), and friction damping to isolate diesel idle shake from the transmission. You will see DMF hardware on many 3.0 EcoDiesel applications, many TDI manuals and some DSG setups, and some Cummins pickup applications (certain G56 or other manual/auto pairings). A 6.7 Power Stroke automatic still uses a conventional flexplate.

Failed DMF symptoms:

  • Booming rattle at idle in gear that fades as rpm rises (springs packing or broken)
  • Shudder on clutch or converter engagement
  • Broken springs that you can hear sloshing or rattling when the unit is removed
  • Heat that cooked the grease in the arc-spring cavity

Do not resurface a dual-mass flywheel like a conventional flywheel. You can destroy the spring pack and the friction damping. Inspect for cracks, spring failure, heat, mounting-face runout, and ring-gear condition, then replace the DMF as an assembly when it fails. Some makers allow a limited ring-gear service; most light-duty units are replaced complete. Support the transmission; a DMF is heavier than a flexplate and will wreck the crank snout if it hangs on one bolt.

Compare complaints: a cold front-cover rattle that sets a correlation code is the chain ; a booming rattle at idle in Drive that never sets a cam code is more likely the DMF or a mount. A spun damper falsifies marks without setting a chain code. Separate those three on the test and in the bay.

Traps: resurfacing a DMF; timing to a spun damper ring; treating every 6.7 as belt-driven; ignoring ring-gear teeth because “the starter is new”; measuring flywheel runout with the indicator on the engine hoist instead of on a fixed point.

Loading diagram... Gear-train, damper, and flywheel inspection split on light-duty diesels