Study guide
1.1 Current Exam Facts
ASE A9 Light Vehicle Diesel Engines Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 ASE Question Formats, Research Items, and Scoring 1.3 Independent Prep Strategy by Content Area Weight
2 Diagnostic Strategy, Scan Data, Inspection, and NVH
2.1 Complaint Verification, VIN, Engine ID, and Service Information 2.2 Scan Tool Data, Freeze Frame, DTCs, and Repair Verification 2.3 Leak Inspection and Engine Compartment Wiring 2.4 Engine Noise and Vibration Diagnosis
3 Smoke, Fuel Quality, Driveability, and Starting
3.1 Exhaust Smoke, Odor, Volume, and Crankcase Pressure 3.2 Fuel Quality, Contamination, Consumption, and Driveability Complaints 3.3 In-Bay Cooling and Lubrication Screening 3.4 No-Crank, No-Start, Battery, and Charging Diagnosis
4 Cylinder Head and Valve Train Diagnosis and Repair
4.1 Cylinder Head Inspection, Thickness, Warpage, Cracks, and Passages 4.2 Valves, Guides, Seats, Springs, Retainers, Locks, and Seals 4.3 Injector/Glow Plug Sleeves, Bridges, Head Gasket Thickness, and TTY Installation 4.4 Valve Train, Lash, Overhead Cam, and Timing Drive
5 Engine Block Diagnosis and Repair
5.1 Pans, Covers, Block Inspection, Deck Height, and Cylinder Walls 5.2 In-Block Camshaft, Crankshaft, Select-Fit Bearings, and End Play 5.3 Pistons, Pins, Rings, Protrusion, and Cooling Jets 5.4 Drive Gear Train, Vibration Damper, Flywheel, Flexplate, and Dual-Mass Flywheel
6 Lubrication Systems Diagnosis and Repair
6.1 Oil Pressure, Sensors, Pump, Screens, and Pressure Regulator 6.2 Oil Cooler, Turbo Lubrication, Filters, and Oil Specification
7 Cooling Systems and Accessory Drive
7.1 Drive Belts, Pulleys, Tensioners, and Alignment 7.2 Thermostats, Water Pump, Coolant Type, Flush, and Bleed 7.3 Radiator, Cap, Pressure Test, Fan, Clutch, Controls, and Shroud
8 Air Induction and Turbocharging
8.1 Air Cleaner, Induction Piping, and Restrictions 8.2 Charge Air Cooler, Piping, and Intake Manifold Pressure Tests 8.3 Turbochargers, Wastegates, and Boost Control 8.4 Variable Geometry Turbochargers and Actuators
9 Exhaust Flow, Glow Plugs, DOC, and DPF
9.1 Intake Manifolds, Exhaust Backpressure, Temperature, and Exhaust Hardware 9.2 Glow Plugs and Inlet Air Heaters 9.3 Diesel Oxidation Catalyst, DPF, and Regeneration
10 SCR, EGR, Throttle Valves, and Crankcase Ventilation
10.1 SCR, Diesel Exhaust Fluid, and NOx Control 10.2 EGR Valves, Coolers, Bypass, Sensors, and Wiring 10.3 Diesel Throttle Valves and Crankcase Ventilation
11 Low-Pressure Fuel Supply
11.1 Fuel Tanks, Vents, Caps, Supply/Return Lines, and Fittings 11.2 Transfer Pump, Water Separators, Filters, Heaters, and Coolers 11.3 Air in Fuel, Priming, Bleeding, and Low-Pressure Regulation
12 High-Pressure Common Rail Fuel Systems
12.1 High-Pressure Lines, Fittings, Seals, Transfer Tubes, and Safety 12.2 Common-Rail Pump, Rail, and Pressure Control 12.3 Common-Rail Injectors, Back-Leakage, and Replacement
13 HEUI, PLN-E, and EUI Fuel Systems
13.1 Hydraulic Electronic Unit Injector (HEUI) Systems 13.2 Pump-Line-Nozzle Electronic and Electronic Unit Injector Systems
14 Fuel Electronics, Scan Diagnosis, and Interrelated Systems
14.1 Injector Calibration Codes, Software Updates, and Control-Module Relearn 14.2 Harnesses, Sensors, Actuators, and DMM Voltage-Drop Testing 14.3 Interrelated Systems, Electronic Throttle, and PTO Controls
1.1 Current Exam Facts
Key Takeaways Explain This Topic AI
Initial ASE A9 is 50 scored questions in 75 minutes at Prometric, with about 10 unlabeled research items on the first certification only.
Recertification A9R is 25 scored questions in 30 minutes and does not add that research block.
2026 fees are a $34 registration charge per order plus a $62 general test fee; A9 is a general test, and you have 90 days from purchase to sit.
Certification needs 2 years of relevant hands-on repair experience; an ASE-accredited training program credits 1 year and an ASE-accredited OEM-sponsored co-op program credits the full 2 years, and you may test before experience is approved.
A9 certifies light-vehicle diesel work and is not required for ASE Master Automobile Technician (A1–A8) and is not interchangeable with ASE T2.
Last updated: September 2026
What A9 certifies
The National Institute for Automotive Service Excellence (ASE) A9 Light Vehicle Diesel Engines test is the Automobile & Light Truck specialty for diesel engines in light vehicles : passenger cars, sport-utility vehicles (SUVs), and light trucks through Class 3 . That is the shop population that actually rolls in for this work—a Ford Power Stroke 6.7-liter Super Duty, a General Motors Duramax L5P in a 2500 pickup, a Ram Cummins 6.7-liter, a Jeep or Ram EcoDiesel , or a Volkswagen Turbocharged Direct Injection (TDI) car. The credential tells a shop, a fleet, or a customer that you can diagnose and repair those engines across fuel, air, aftertreatment, lubrication, cooling, and the mechanical top and bottom end.
A9 sits in the A-series family and is a general test , not an L-level advanced test. Delivery is computer-based at Prometric . A1 through A9 carry a Spanish option that you use during the test , not at registration: a Leer en español button opens a side-by-side Spanish/English rendering of the question and answer choices. ASE states that no special registration process is needed , and you still mark your answer on the English side. This ExamFinch chapter is independent prep covering the published A9 content areas. It is not an ASE publication and does not claim official approval, review, or partnership.
What A9 is not
Two nearby credentials cause most of the scheduling mistakes:
A9 is not required for ASE Master Automobile Technician. Master Automobile status is A1 through A8 . A gasoline-only Master technician can hold that credential without ever sitting A9. A diesel specialist can hold A9 without being a Master. Do not buy A9 because you think the blue Master seal is incomplete without it.
A9 is not ASE T2 Medium/Heavy Truck Diesel Engines. T2 belongs to the medium/heavy truck series and is built around Class 4–8 engines, vocational duty cycles, and truck-shop procedures. Charge-air coolers and diesel particulate filters appear in both worlds, but A9 examples stay in light-duty packaging, sensors, and control strategies. Passing A9 does not certify a Class 8 highway tractor the way T2 does.
A9 is not a manufacturer brand cert. It does not replace Ford, GM, Stellantis, or Volkswagen factory diesel training, calibration access, or special tools. Brand service information still governs the repair in the bay.
Write those three limits on the same card as the question count. Technicians who study T2 Class 8 regeneration playbooks and skip pickup-truck diesel exhaust fluid (DEF) tanks, car-platform glow-plug modules, and light-duty charge-air routing will miss the A9 fence.
Published 2026 length, timing, and on-screen count
ASE's A1–A9 test page is the source for the numbers you will pace against:
- Format Scored questions Time Research items
- Initial A9 50 75 minutes About 10 unscored items, initial certification only
- Recertification A9R 25 30 minutes None published for recert
The initial sitting therefore puts about 60 items on the screen: 50 that count plus about 10 research items ASE is evaluating. You cannot see which is which. Recertification is the short form and does not add that research block. If you use the full 75 minutes on about 60 items, you have roughly 75 seconds per item . Direct questions should take less. Technician A / Technician B stems and EXCEPT stems take more. Flag and move; do not spend four minutes rereading one stem while unanswered items sit at the end.
Those 50 scored questions are the real exam length. They are not the size of any third-party practice bank, including the independent ExamFinch bank. Practice inventory is optional rehearsal. The live test is 50 scored items in 75 minutes at Prometric.