Study guide
6.2 Starting and Charging System Diagnostics
ASE G1 Auto Maintenance and Light Repair Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Engine Systems
1.1 Engine Oil and Filter Service 1.2 Cooling and Drive Belt Maintenance 1.3 Air and Fuel Filter Service 1.4 Spark Plugs and Basic Engine Diagnostics 1.5 Engine Leak, Noise, and Cover Inspection 1.6 Exhaust, EVAP, and DEF Service
2 Chapter 2: Automatic Transmission/Transaxle
2.1 Transmission Fluid Level and Condition Checks 2.2 Transmission Fluid Service and Basic Diagnostics
3 Chapter 3: Manual Drive Train and Axles
3.1 Clutch and Manual Transmission Service 3.2 CV Joints, Boots, and Axles 3.3 Driveshafts, U-Joints, and Differentials 3.4 Four-Wheel Drive and Transfer Case Service
4 Chapter 4: Suspension and Steering
4.1 Shock Absorbers and Struts 4.2 Ball Joints and Control Arms 4.3 Steering Linkage and Gear Inspection 4.4 Stabilizer Bars and Springs 4.5 Power Steering System Service 4.6 Wheel Alignment and Tire Wear Diagnostics 4.7 Tires, TPMS, and Wheel Service 4.8 Rear Suspension Inspection
5 Chapter 5: Brakes
5.1 Disc Brake Inspection and Pad Replacement 5.2 Drum Brake Inspection and Shoe Replacement 5.3 Hydraulic System and Brake Fluid Service 5.4 Brake Bleeding and ABS Modulator Diagnostics 5.5 Parking Brake and Caliper Diagnostics 5.6 Power Brake Assist Systems
6 Chapter 6: Electrical
6.1 Battery Testing and Service 6.2 Starting and Charging System Diagnostics 6.3 Lighting System Inspection and Bulb Replacement 6.4 Fuses, Relays, and Basic Wiring 6.5 Body Electrical Accessories and SRS Precautions
7 Chapter 7: Heating, Ventilation, and Air Conditioning (HVAC)
7.1 A/C System Inspection and Performance Checks 7.2 Heating System and Engine Cooling Integration
6.2 Starting and Charging System Diagnostics
Key Takeaways Explain This Topic AI
Starter draw testing uses an inductive amp clamp to measure current during cranking to diagnose mechanical binding or starter shorts.
Under-load alternator output testing should yield 13.5V to 14.5V at 2,000 RPM with all heavy accessories running.
Alternator AC ripple should remain below 0.5V AC to ensure rectifier diodes are properly converting AC to DC voltage.
Voltage drop testing evaluates resistance under active load, with a strict maximum limit of 0.2V on the ground circuit.
Diagnose starter control switches/relays before replacing starters; verify belt and tensioner condition when charging output is low.
Last updated: July 2026
Starting and Charging System Diagnostics
The starting and charging systems are closely linked, relying on the battery to initiate combustion and the alternator to replenish the battery and power the vehicle’s electrical loads during operation. Diagnosing these systems requires a combination of current draw testing, voltage drop testing, and alternator output verification.
Starter Circuit Current Draw Testing
A starter current draw test measures the amount of electrical current (amperage) the starter motor requires to crank the engine. This test is performed using an inductive amp clamp wrapped around the battery cable (typically the negative or positive feed to the starter) and connected to a digital multimeter or engine analyzer.
Test Procedure
Disable the engine's ignition or fuel system to prevent the engine from starting (e.g., remove the fuel pump relay or disconnect the ignition coils).
Attach the inductive amp clamp around the main starter power cable, noting the arrow direction indicating current flow. Zero the clamp.
Crank the engine for 3 to 5 seconds and note the peak amperage reading.
Analyzing Current Draw Results
Starter current draw varies by engine size (larger engines require more current to compress air in the cylinders), but technicians look for specific diagnostic combinations:
High Amperage Draw / Slow Cranking : Indicates either an internal short circuit in the starter motor armature, worn starter shaft bushings causing the armature to drag against the field coils (known as starter pole drag), or mechanical binding inside the engine itself (such as a seized bearing or tight engine).
Low Amperage Draw / Slow Cranking : Points to excessive resistance in the starting circuit (corrosion, loose connections, or undersized cables) or a degraded battery that cannot deliver sufficient current.
Normal Amperage Draw / Slow Cranking : Usually indicates a mechanical engine problem, incorrect engine oil viscosity, or incorrect ignition timing.
Alternator Output and Charging Voltage Testing
The charging system must maintain system voltage and recharge the battery. The alternator utilizes a rotor, stator, and a rectifier diode bridge to generate and convert alternating current (AC) into direct current (DC) for the vehicle.
Charging Voltage Under Load
To test the charging voltage:
Connect a DMM across the battery terminals (red to positive, black to negative) set to DC Volts.
Start the engine and run it at approximately 2,000 RPM.
Turn on heavy electrical accessories (headlights on high beam, A/C blower on high speed, rear window defogger).
Read the voltage. A healthy charging system should maintain a voltage of 13.5V to 14.5V under load .
If the voltage is below 13.5V, the alternator is undercharging, which will lead to a discharged battery. If the voltage exceeds 15.0V, the voltage regulator is faulty, which will overcharge the battery and damage sensitive electronic modules.
AC Ripple Testing
Alternators use diodes to rectify AC voltage to DC. If a diode is blown or leaking, it allows AC voltage to enter the vehicle's electrical system. This causes electrical noise, module communication errors, and battery drain.
How to test : Set the DMM to AC Volts and connect the leads across the battery terminals while the engine is running.
Specification : A healthy alternator should show less than 0.5V AC (usually less than 0.1V AC). Any reading above 0.5V AC indicates a failed rectifier diode bridge.
Smart Charging Systems and Temperature Compensation
Modern vehicles utilize computer-controlled charging systems where the Powertrain Control Module (PCM) or Body Control Module (BCM) monitors battery temperature. A battery temperature sensor—often integrated into the negative terminal clamp or located on the battery tray—provides this data. Because battery chemistry is temperature-dependent, the charging voltage must adjust accordingly. In cold ambient temperatures, the controller increases charging voltage (up to 15.0V) to overcome high battery resistance and speed up recovery. In extremely hot weather, the controller decreases the charging voltage (sometimes down to 13.2V) to prevent battery gassing, electrolyte loss, and thermal runaway.
Voltage Drop Testing
Voltage drop testing is the most accurate method to locate high resistance in starting and charging circuits. Unlike a static resistance (ohm) test, which is done with the circuit turned off, a voltage drop test measures resistance while current is actively flowing through the circuit.
Loading diagram...
How to Perform a Voltage Drop Test
Set the DMM to DC Volts (or millivolts).
Connect the voltmeter leads in parallel across the component or cable being tested (e.g., one lead on the battery positive post, the other lead on the starter solenoid B+ terminal).
Crank the engine or operate the circuit to load the wiring.
Read the voltmeter. The reading represents the voltage "lost" due to resistance in that cable or connection.
Voltage Drop Specifications
Technicians use the following limits to determine if a circuit has excessive resistance:
- Circuit Segment Maximum Allowable Voltage Drop
- Total Starting Circuit (Positive Side) 0.5V
- Individual Starting Cable or Connection 0.2V
- Starter Ground Circuit (Negative Side) 0.2V
- Charging System Output Cable (B+) 0.3V
- Alternator Ground Circuit 0.2V
If the voltage drop exceeds 0.2V on the ground side or 0.5V total on the positive starting circuit, there is high resistance (such as corrosion, a loose terminal, or frayed wires) that must be repaired.
Starter Control Circuit and Alternator Drive Components
A no-crank complaint is not always a bad starter. Verify battery state of charge first, then test the starter control circuit : ignition/start signal, neutral safety or clutch pedal switch, starter relay, and control-circuit wiring. Voltage should appear at the starter solenoid control terminal during a crank request; if not, diagnose switches and relays before replacing the starter. Excessive starter current draw with a known-good battery indicates mechanical binding or a failing starter; low draw with slow cranking often points to high resistance in cables or grounds.
On the charging side, inspect the alternator drive belt, pulleys, and tensioner before condemning an alternator for undercharge. A slipping belt can pass a quick unloaded voltage check yet collapse under load (headlights + blower + rear defogger). Replace glazed belts and weak tensioners with the alternator when output is marginal.