Study guide

3.3 Driveshafts, U-Joints, and Differentials

ASE G1 Auto Maintenance and Light Repair Certification Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Engine Systems

1.1 Engine Oil and Filter Service 1.2 Cooling and Drive Belt Maintenance 1.3 Air and Fuel Filter Service 1.4 Spark Plugs and Basic Engine Diagnostics 1.5 Engine Leak, Noise, and Cover Inspection 1.6 Exhaust, EVAP, and DEF Service

2 Chapter 2: Automatic Transmission/Transaxle

2.1 Transmission Fluid Level and Condition Checks 2.2 Transmission Fluid Service and Basic Diagnostics

3 Chapter 3: Manual Drive Train and Axles

3.1 Clutch and Manual Transmission Service 3.2 CV Joints, Boots, and Axles 3.3 Driveshafts, U-Joints, and Differentials 3.4 Four-Wheel Drive and Transfer Case Service

4 Chapter 4: Suspension and Steering

4.1 Shock Absorbers and Struts 4.2 Ball Joints and Control Arms 4.3 Steering Linkage and Gear Inspection 4.4 Stabilizer Bars and Springs 4.5 Power Steering System Service 4.6 Wheel Alignment and Tire Wear Diagnostics 4.7 Tires, TPMS, and Wheel Service 4.8 Rear Suspension Inspection

5 Chapter 5: Brakes

5.1 Disc Brake Inspection and Pad Replacement 5.2 Drum Brake Inspection and Shoe Replacement 5.3 Hydraulic System and Brake Fluid Service 5.4 Brake Bleeding and ABS Modulator Diagnostics 5.5 Parking Brake and Caliper Diagnostics 5.6 Power Brake Assist Systems

6 Chapter 6: Electrical

6.1 Battery Testing and Service 6.2 Starting and Charging System Diagnostics 6.3 Lighting System Inspection and Bulb Replacement 6.4 Fuses, Relays, and Basic Wiring 6.5 Body Electrical Accessories and SRS Precautions

7 Chapter 7: Heating, Ventilation, and Air Conditioning (HVAC)

7.1 A/C System Inspection and Performance Checks 7.2 Heating System and Engine Cooling Integration

3.3 Driveshafts, U-Joints, and Differentials

Key Takeaways Explain This Topic AI

A dented driveshaft tube can cause severe speed-dependent vibrations and catastrophic driveshaft failure under load.

A dry universal joint (U-joint) produces a squeaking or chirping noise at low speeds, and exhibits 'red rust' bleeding from its bearing cup seals.

Universal joints must have zero radial or axial play; any movement requires immediate replacement of the joint.

Limited-slip differentials (LSD) require a specific friction modifier additive to prevent clutch plates from chattering during tight turns.

Replace failed center support bearings and verify driveshaft phasing; clear axle vents and replace damaged wheel studs properly.

Last updated: July 2026

Driveshafts, U-Joints, and Differentials

Quick Answer: RWD and AWD drivetrains rely on balanced driveshafts and universal joints (U-joints) to transmit torque. Driveshaft dents or runout cause speed-dependent vibrations. Worn U-joints exhibit loose play, clunking, or squeaking noises accompanied by red rust dust. Rear differentials must be filled to the plug level with correct gear oil, and limited-slip units require friction modifier additives to prevent clutch chatter on turns. Pinion seal service must preserve bearing preload.

RWD, 4WD, and AWD vehicles use driveshafts to connect the transmission to rear differentials, which split torque to drive axles. Service requires careful inspection of balance, joint play, and lubricants.

Driveshaft Inspection and Runout

The driveshaft is a hollow, thin-walled metal tube that spins at high speeds. Distortion in shape or balance results in severe, speed-dependent vibrations.

Physical Damage: Inspect the tube for dents, scrapes, or missing balance weights. Dents concentrate stresses and cause the driveshaft to bend or twist under load, leading to catastrophic failure. Missing weights leave a clean unpainted spot or weld residue.

Runout Measurement: If a bent shaft is suspected, measure runout with a dial indicator. Mount the indicator base to the frame and place the plunger perpendicular to the clean shaft. Rotate by hand through one full turn at the front, center, and rear. Record the total indicator reading (TIR). Runout exceeding limits (usually 0.010 to 0.030 inches) requires driveshaft replacement.

Vibration: Out-of-balance or bent driveshafts produce a high-frequency vibration felt in the seat and floorboards. This increases in frequency and intensity with vehicle speed, regardless of engine load or cornering.

Universal Joint (U-Joint) Inspection

Universal joints (U-joints) are flexible crosses with needle-bearing cups. They transmit power through angles that change as the rear axle moves over bumps.

Testing for Play: Raise the vehicle and place transmission in neutral to unload torque. Grasp the driveshaft near the U-joint and twist back and forth while holding the yoke stationary. Move the joint radially and axially. There must be zero play; any movement indicates worn needle bearings, requiring U-joint replacement.

Squeaking and Chirping: A dry U-joint produces a squeaking or chirping noise at low speeds (5 to 20 mph) that changes with wheel speed, indicating needle bearings are dry and grinding.

Red Dust Bleeding: A reddish-brown powder (red dust) near the cup seals indicates "rust bleeding"—iron oxide produced by dry needle bearings grinding the cross journal.

Clunking: A worn joint produces a clunk when shifting from Park to Drive or Reverse, or during acceleration.

Rear Differential Service and LSD Additives

The differential contains a ring and pinion gear set that redirects torque 90 degrees.

Fluid Level Checks: Remove the fill plug. The gear oil level should be flush with the bottom edge of the fill hole.

Fluid Exchange: Replace fluid periodically to drain wear particles. Remove the drain plug or rear cover, drain oil, clean the internal magnet, apply a new gasket/RTV, and refill with specified GL-5 gear oil (typically SAE 75W-90).

Limited-Slip Differentials (LSD): LSDs use clutch packs to transfer torque. During turns, these plates must slip to allow different wheel speeds.

Friction Modifiers: LSDs require gear oil with a friction modifier additive. Without this additive, the clutch plates stick and grab unevenly, causing a severe chatter or shudder in the rear axle during tight turns.

Pinion and Axle Seal Service

Pinion Seal Leakage: Pinion seals prevent gear oil leaks at the input yoke. A leak here slings oil under the vehicle floorboard.

Pinion Preload: The pinion nut compresses a crush sleeve to set pinion bearing preload. To replace the seal, mark the position of the shaft, nut, and yoke, and count exposed threads. Measure rotating torque (preload) before disassembly. During reassembly, tighten the nut exactly to the marks and verify rotating torque to avoid over-tightening and burning bearings.

Axle Seals: Leaks at the wheel ends coat rear brakes. This contaminates shoes or pads, causing pulling, grabbing, or reduced braking efficiency.

RWD/AWD Drivetrain Components and Inspection Criteria

Component Inspection Method Failed State / Symptom Repair Action

Driveshaft Tube Visual & dial indicator runout test Dents, missing balance weights, runout exceeding limit (e.g. >0.020") Rebalance or replace driveshaft assembly

Universal Joints Rotate shaft, use pry bar Loose play, binding, red rust/powder around seals, chirping noise Replace U-joint assembly

Differential Pinion Seal Visual check at input yoke Gear oil leaking onto yoke and underbody; low fluid level Replace seal; maintain pinion bearing preload

Rear Axle Seals Visual check behind brake backing plate Fluid leaking onto brake components, contaminated shoes/pads Replace seal and brake linings; clean assembly

Limited-Slip Differential Road test with tight turns Shuddering, chattering, or binding during turns Service fluid; add specified LSD friction modifier

Loading diagram...

Center Support Bearings, Wheel Studs, and Axle Housing Checks

On two-piece driveshafts, the center support bearing (carrier bearing) supports the shaft at the middle. A failed bearing produces a howl or vibration that changes with speed and may show a sagging rubber isolator. Replace the bearing and verify shaft phasing (yoke alignment marks) during reassembly—incorrect phasing causes a severe vibration.

For rear-wheel-drive axles, identify lubricant leaks at the pinion seal, cover gasket, and axle shaft seals. Drain and refill with the specified gear lubricant (and friction modifier when required for limited-slip units). Inspect the axle housing and vent; a clogged vent pressurizes the housing and forces oil past seals. Replace damaged rear axle shaft wheel studs individually when threads are stripped or the stud is broken—use the correct press or draw-in method and never drive a stud crooked into the flange.