Study guide
4.1 Shock Absorbers and Struts
ASE G1 Auto Maintenance and Light Repair Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Engine Systems
1.1 Engine Oil and Filter Service 1.2 Cooling and Drive Belt Maintenance 1.3 Air and Fuel Filter Service 1.4 Spark Plugs and Basic Engine Diagnostics 1.5 Engine Leak, Noise, and Cover Inspection 1.6 Exhaust, EVAP, and DEF Service
2 Chapter 2: Automatic Transmission/Transaxle
2.1 Transmission Fluid Level and Condition Checks 2.2 Transmission Fluid Service and Basic Diagnostics
3 Chapter 3: Manual Drive Train and Axles
3.1 Clutch and Manual Transmission Service 3.2 CV Joints, Boots, and Axles 3.3 Driveshafts, U-Joints, and Differentials 3.4 Four-Wheel Drive and Transfer Case Service
4 Chapter 4: Suspension and Steering
4.1 Shock Absorbers and Struts 4.2 Ball Joints and Control Arms 4.3 Steering Linkage and Gear Inspection 4.4 Stabilizer Bars and Springs 4.5 Power Steering System Service 4.6 Wheel Alignment and Tire Wear Diagnostics 4.7 Tires, TPMS, and Wheel Service 4.8 Rear Suspension Inspection
5 Chapter 5: Brakes
5.1 Disc Brake Inspection and Pad Replacement 5.2 Drum Brake Inspection and Shoe Replacement 5.3 Hydraulic System and Brake Fluid Service 5.4 Brake Bleeding and ABS Modulator Diagnostics 5.5 Parking Brake and Caliper Diagnostics 5.6 Power Brake Assist Systems
6 Chapter 6: Electrical
6.1 Battery Testing and Service 6.2 Starting and Charging System Diagnostics 6.3 Lighting System Inspection and Bulb Replacement 6.4 Fuses, Relays, and Basic Wiring 6.5 Body Electrical Accessories and SRS Precautions
7 Chapter 7: Heating, Ventilation, and Air Conditioning (HVAC)
7.1 A/C System Inspection and Performance Checks 7.2 Heating System and Engine Cooling Integration
4.1 Shock Absorbers and Struts
Key Takeaways Explain This Topic AI
Shock absorbers and struts convert suspension spring kinetic energy into thermal energy through metered hydraulic fluid flow.
Gas charging with high-pressure nitrogen prevents fluid aeration (foaming) to prevent damping fade during rapid suspension cycling.
Misting is a normal dust-collecting oil film from seal lubrication, whereas active dripping indicates seal failure requiring damper replacement.
A bounce test should settle the vehicle within 1 to 1.5 cycles; additional bouncing indicates failed dampers.
Deteriorated upper strut mount bearings cause steering stiffness, memory steer, and popping noises as the coil spring binds and releases.
Last updated: July 2026
- 4.1 Shock Absorbers and Struts
- Shock and Strut Operation
Suspension springs (coil, leaf, or torsion bar) absorb road shocks by compressing. However, a spring releases this energy by bouncing repeatedly. Without damping, the vehicle would continuously oscillate, causing the tires to lose contact with the road. Shock absorbers and struts are velocity-sensitive hydraulic dampers that convert the spring's kinetic energy into thermal energy.
Inside the damper, a piston moves through hydraulic fluid. As the suspension compresses (jounce) or extends (rebound), fluid is forced through metered orifices and spring-loaded valves in the piston. This resistance slows the spring's movement. Modern dampers are gas-charged with pressurized nitrogen gas (100–360 psi) to prevent aeration (foaming). Aeration occurs during rapid piston movement when low-pressure zones allow gas bubbles to form in the fluid. Since foam flows too easily, it causes "damping fade." The gas pressure keeps the fluid under compression, preventing foaming and ensuring consistent control.
Shock Absorbers vs. Struts: Key Differences
Technicians must distinguish between shocks and struts, as they dictate different repair and alignment procedures.
Feature Shock Absorber Strut (MacPherson)
Structural Role Non-structural; does not support weight. Structural member; acts as the upper control link.
Steering Pivot No; does not rotate with steering. Yes; rotates on an upper bearing assembly.
Alignment Impact None; removal does not affect alignment. Critical; directly controls camber and caster.
Assembly Mounted separately from the spring. Houses the coil spring and mount.
Suspension Type Double-wishbone (SLA) or solid axle. MacPherson strut suspension systems.
Leak Inspection: Normal Misting vs. Active Dripping
Dampers rely on a precise fluid volume. Fluid loss leads to a complete loss of damping. However, not all wetness indicates failure.
Normal Misting (Oil Film): A microscopic oil layer clings to the piston rod to lubricate the main shaft seal. During normal cycling, this oil deposits on the outer body tube. Road dust collects on this film, creating a dry, dark, slightly damp appearance near the seal. This is normal misting, is dry to the touch, does not run down the shock body, and does not require replacement.
Active Dripping (Failure): A failed seal allows fluid to escape in large quantities. This is characterized by wet, liquid oil coating the body, forming active drips at the bottom, or pooling on the lower spring seat. If the fluid runs down the body and is wet to the touch, the seal has failed and the damper must be replaced, typically in pairs across the axle.
Physical Damage Diagnostics
Visual inspections should target physical damage that restricts damper movement or compromises structural integrity:
Bent Shafts: A bent piston rod binds in the guide, causing steering stiffness, noise (groaning/squeaking), and rapid seal destruction.
Dented Housings: A dent in the outer tube of a twin-tube housing pinches the inner cylinder, binding the piston.
Corrosion: Severe rust weakens the structural integrity of a strut body. If the lower spring seat collapses, the coil spring falls onto the tire, causing immediate loss of vehicle control.
Jounce Bumpers and Dust Boots: The rubber bump stop prevents metal-to-metal contact when the suspension bottoms out. The dust boot protects the piston shaft. Torn boots allow dirt to score the polished rod, destroying the seal. Damaged bump stops indicate frequent bottoming from weak springs.
Bounce Test Diagnostics
The bounce test is a standard method to assess damper health:
Push down firmly on one corner of the vehicle's bumper to compress the suspension.
Release the vehicle quickly and count the oscillations.
A healthy damper should settle back to ride height within 1 to 1.5 cycles .
If the vehicle continues to bounce (2 or more cycles), the damper is weak and must be replaced.
On the road, weak damping causes a floating ride, nose-dive under hard braking, rear-end squat during acceleration, and excessive body roll. This instability reduces tire contact, extending braking distances.
Strut Mounts and Bearings
The top of a MacPherson strut attaches to the unibody tower via an upper strut mount containing a rubber bushing and a steering bearing.
Rubber Isolation Bushing: This bushing dampens high-frequency road vibrations. Over time, the rubber degrades, cracks, or collapses. This results in metal-to-metal contact, producing a loud clunking noise over bumps and shifting alignment angles.
Thrust Bearing: On front steering axles, the strut rotates as the wheels turn. The thrust bearing allows the assembly to pivot smoothly. If the bearing binds due to rust or wear, it causes steering stiffness, memory steer (pulling in the direction of the last turn), and popping or clicking noises as the coil spring binds and releases during steering.
MacPherson Strut Service Safety
When servicing MacPherson struts, technicians must prioritize safety. The coil spring is mounted directly on the strut body under immense tension. To replace a worn strut cartridge, coil spring, or upper mount, the technician must compress the spring using a specialized strut compressor. The spring must be compressed until it is loose from the upper and lower spring seats. Only then can the piston rod center nut be safely loosened. Removing the center nut before the spring is fully compressed will cause a catastrophic release of the spring's stored energy, resulting in severe injury and destruction of shop equipment.
Loading diagram...