Study guide

4.7 Tires, TPMS, and Wheel Service

ASE G1 Auto Maintenance and Light Repair Certification Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Engine Systems

1.1 Engine Oil and Filter Service 1.2 Cooling and Drive Belt Maintenance 1.3 Air and Fuel Filter Service 1.4 Spark Plugs and Basic Engine Diagnostics 1.5 Engine Leak, Noise, and Cover Inspection 1.6 Exhaust, EVAP, and DEF Service

2 Chapter 2: Automatic Transmission/Transaxle

2.1 Transmission Fluid Level and Condition Checks 2.2 Transmission Fluid Service and Basic Diagnostics

3 Chapter 3: Manual Drive Train and Axles

3.1 Clutch and Manual Transmission Service 3.2 CV Joints, Boots, and Axles 3.3 Driveshafts, U-Joints, and Differentials 3.4 Four-Wheel Drive and Transfer Case Service

4 Chapter 4: Suspension and Steering

4.1 Shock Absorbers and Struts 4.2 Ball Joints and Control Arms 4.3 Steering Linkage and Gear Inspection 4.4 Stabilizer Bars and Springs 4.5 Power Steering System Service 4.6 Wheel Alignment and Tire Wear Diagnostics 4.7 Tires, TPMS, and Wheel Service 4.8 Rear Suspension Inspection

5 Chapter 5: Brakes

5.1 Disc Brake Inspection and Pad Replacement 5.2 Drum Brake Inspection and Shoe Replacement 5.3 Hydraulic System and Brake Fluid Service 5.4 Brake Bleeding and ABS Modulator Diagnostics 5.5 Parking Brake and Caliper Diagnostics 5.6 Power Brake Assist Systems

6 Chapter 6: Electrical

6.1 Battery Testing and Service 6.2 Starting and Charging System Diagnostics 6.3 Lighting System Inspection and Bulb Replacement 6.4 Fuses, Relays, and Basic Wiring 6.5 Body Electrical Accessories and SRS Precautions

7 Chapter 7: Heating, Ventilation, and Air Conditioning (HVAC)

7.1 A/C System Inspection and Performance Checks 7.2 Heating System and Engine Cooling Integration

4.7 Tires, TPMS, and Wheel Service

Key Takeaways Explain This Topic AI

Cold inflation pressure is set to the vehicle placard specification, not the maximum pressure molded into the tire sidewall.

Tire wear patterns reveal alignment, inflation, and suspension faults before a blowout occurs.

Lug nuts must be torqued in a star or crisscross pattern to prevent warped brake rotors and loose wheels.

Direct TPMS uses in-wheel pressure sensors; indirect TPMS infers pressure from wheel-speed ABS signals.

Puncture repairs are limited to the tread crown; shoulder or sidewall damage requires tire replacement.

Last updated: July 2026

4.7 Tires, TPMS, and Wheel Service

Tires are the only contact point between the vehicle and the road. Proper inflation, tread depth, load and speed ratings, rotation, mounting, balancing, and TPMS service directly affect braking distance, fuel economy, steering response, and occupant safety. ASE G1 technicians must inspect tires systematically, correct inflation to placard specifications, diagnose vibration and noise, service wheels without damaging TPMS hardware, and perform repairs only where manufacturer standards allow.

Tire Inspection: Condition, Tread, and Ratings

A complete tire inspection begins with a walk-around and continues with hands-on checks at each wheel.

Tread Depth and Legal Limits

Measure tread depth at the center and both outer grooves using a tread depth gauge. The industry replacement threshold is 2/32 inch (1.6 mm) —the point where wet traction and hydroplaning resistance drop sharply. Many technicians recommend replacement at 4/32 inch on drive wheels and 2/32 inch on non-drive axles when budgets allow. Wear bars molded across the tread grooves appear flush with the tread surface at 2/32 inch, providing a visual wear indicator.

Sidewall, Bead, and Structural Damage

Inspect sidewalls for cuts, bulges, ozone cracking, and impact damage from curbs or potholes. A bulge indicates broken internal cords and requires immediate replacement—do not attempt repair. Check for objects embedded in the tread; note puncture location. Examine the bead area for damage from improper mounting or corrosion on steel wheels.

Size, Load Index, and Speed Rating

The tire size (e.g., P215/65R16) must match the placard or owner manual specification. The load index is a numeric code indicating maximum load per tire at maximum inflation; the speed rating letter (e.g., H, V, W) defines the maximum sustained speed capability. Replacements must meet or exceed placard load and speed requirements. Mixing tire sizes, constructions (radial vs. bias), or speed ratings on the same axle degrades handling and may trigger ABS or stability control faults.

  • Wear Pattern Appearance Primary Cause Corrective Action
  • Center wear Smooth center, unworn shoulders Over-inflation Adjust to placard cold pressure
  • Shoulder wear (both sides) Worn edges, high center Under-inflation Inflate to placard; check for slow leaks

One-shoulder wear Single edge worn Camber misalignment or worn suspension Perform alignment and suspension inspection

Feathering / sawtooth Ridges felt when hand-swept Toe misalignment Adjust toe; inspect steering linkage

Cupping / scalloping Random high-low spots Worn shocks/struts or out-of-balance assembly Replace dampers; balance wheels

Diagonal wear Wear at an angle across tread Aggressive driving, misalignment, or mismatched inflation Align, balance, and verify pressures

Inflation: Placard vs. Sidewall Maximum

Tire pressure is always set to the vehicle placard (driver door jamb, fuel door, or glove box label), not the maximum pressure molded into the tire sidewall. The sidewall maximum (often 44–51 psi on passenger tires) is the highest pressure the tire casing can safely hold for load-carrying capacity—it is not the recommended daily operating pressure.

Cold Inflation Procedure

Check pressure when tires are cold (vehicle parked at least 3 hours or driven less than one mile).

Use an accurate gauge; compare against placard values for front, rear, and spare if equipped.

Adjust in small increments; recheck after seating the valve core.

Replace missing valve caps and damaged valve stems; metal clamp-in stems are common on TPMS-equipped wheels.

Under-inflation causes heat buildup, sidewall flex fatigue, and increased rolling resistance. Over-inflation reduces contact patch area, stiffens ride quality, and accelerates center tread wear.

Diagnosing Vibration, Shimmy, and Noise

Wheel and tire complaints require distinguishing speed-related from non-speed-related symptoms.

High-speed vibration (55–70+ mph): Often dynamic imbalance, out-of-round tire, or bent wheel. Balance the assembly on a modern balancer that measures both static and dynamic forces.

Low-speed shimmy (15–40 mph): May indicate separated tire belts, excessive radial force variation, or worn suspension components.

Steering wheel shake under braking: Usually warped brake rotors, not tire balance.

Humming or growling: Tread pattern noise, uneven wear, or wheel bearing wear—correlate with cornering load changes.

Always verify tire pressures and lug nut torque before condemning a tire or balancer. Inspect runout with a dial indicator on the wheel lip if vibration persists after balancing.

Rotation, Lug Nut Torque, and Wheel Locks

Tire rotation extends tread life by equalizing wear across positions. Follow the pattern in the owner's manual—common patterns include forward cross, rearward cross, and X-pattern for non-directional tires. Directional tires (marked with rotation arrows) must stay on the same side of the vehicle; only front-to-rear movement is permitted unless the tire is remounted.

Lug Nut Torque and Star Pattern

After any wheel removal, clean hub mating surfaces of rust and debris. Hand-start all lug nuts to prevent cross-threading. Tighten in a star (crisscross) pattern in multiple stages—typically snug by hand, then final torque with a calibrated torque wrench to manufacturer specification (often 80–100 ft-lbs on passenger cars).

Uneven lug nut torque causes brake rotor distortion (pedal pulsation) and can loosen wheels in service. Never use an impact wrench for final torque unless a torque stick or post-torque verification is performed. Re-torque after 50–100 miles when specified (common after new wheels or rotors).

Wheel lock keys must be accounted for before service; apply anti-seize only where specified—never on tapered seat lug nuts unless directed by the manufacturer.

Mounting, Dismounting, and Balancing

Use a tire changer with the correct clamping method for the wheel type (outside clamp vs. internal clamp for polished or clad wheels). Lubricate bead area with approved tire-mounting paste—never petroleum products that degrade rubber.

TPMS Sensor Care During Service

Direct TPMS sensors mount to the valve stem or band inside the wheel. When breaking the bead, position the tool away from the sensor (typically 180° from the valve). Replace service kits (nut, grommet, valve core, cap) per manufacturer interval. Torque sensor retaining nuts to specification—over-torquing cracks the sensor housing.

Static vs. Dynamic Balance

Static imbalance: Heavy spot causes the wheel to bounce up and down. Corrected with a single weight on the plane of imbalance.

Dynamic imbalance: Heavy areas on opposite sides of the wheel at different planes cause side-to-side wobble. Requires weights on both inner and outer planes.

Modern road-force balancers measure radial force variation and recommend clocking the tire on the wheel to minimize vibration. Match-mounting (aligning tire low spot with wheel high spot) improves ride quality on sensitive vehicles.

Tire Repair Standards

Puncture repairs must follow Rubber Manufacturers Association (RMA) or tire-maker guidelines. Repairs are permitted only in the tread crown (the flat contact area), never in the shoulder or sidewall. The injury must be no larger than 1/4 inch (6 mm). Use a combination plug-patch unit from inside the tire after buffing and vulcanizing cement application. Never install a plug-only repair from the outside on a street tire—it does not seal the inner liner and can fail at speed.

Loading diagram...

TPMS Identification, Testing, and Relearn

Direct TPMS uses a battery-powered sensor in each wheel transmitting pressure and temperature. Indirect TPMS uses ABS wheel-speed data; an underinflated tire has a smaller rolling radius and rotates slightly faster than properly inflated tires on the same axle.

Verification Steps

Turn ignition on; confirm the TPMS warning lamp bulb check illuminates briefly at startup, then extinguishes.

Use a scan tool or dedicated TPMS tool to read sensor IDs, pressure, and battery status on direct systems.

On indirect systems, ensure all tires are inflated to placard pressure, then drive at specified speed/duration to reset monitoring.

Relearn Procedures

After tire rotation, sensor replacement, or winter tire swap, perform the manufacturer relearn procedure: stationary magnet sequence, OBD relearn, or drive cycle. Failure to relearn causes false warnings or incorrect location data. Document sensor positions after rotation on direct systems.