Study guide
3.1 OBD-II Standards and Communication
ASE Advanced Engine Performance Specialist L1
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Overview
1.1 Current Exam Facts 1.2 How to Use This Guide
2 Chapter 2: General Powertrain Diagnosis
2.1 Engine Mechanical Diagnosis 2.2 Fuel System Pressure and Flow 2.3 Charging and Starting System Diagnosis 2.4 Drivetrain Issues Affecting Engine Performance 2.5 Diagnostic Strategy and Logical Sequencing
3 Chapter 3: Computerized Powertrain Controls
3.1 OBD-II Standards and Communication 3.2 Input Sensors 3.3 Output Actuators and ECM Control 3.4 Fuel Trim and Oxygen Sensors 3.5 Scan Tool Diagnostics 3.6 Network Communication and U-Codes
4 Chapter 4: Ignition Systems
4.1 Ignition System Types and Coil Operation 4.2 Primary Ignition Diagnosis 4.3 Secondary Ignition Diagnosis 4.4 Spark Plugs and Diagnostic Reading 4.5 Ignition Timing and Knock Sensor
5 Chapter 5: Fuel and Air Induction
5.1 Air Induction System Diagnosis 5.2 Port Fuel Injection (PFI) 5.3 Gasoline Direct Injection (GDI) 5.4 Turbocharger and Supercharger Diagnosis 5.5 Variable Valve Timing and Intake Tuning
6 Chapter 6: Emission Controls
6.1 Emission Standards and Pollutants 6.2 Catalytic Converter Operation and Diagnosis 6.3 EGR System Diagnosis 6.4 EVAP and PCV Systems 6.5 Air Injection and Secondary Air
7 Chapter 7: I/M Failure Diagnosis
7.1 Inspection and Maintenance Programs 7.2 Drive Cycle for Readiness Monitors 7.3 Diagnosing P0420/P0430 Catalyst Codes 7.4 Diagnosing Misfire and Multiple-Cylinder Misfire Codes 7.5 Diagnosing Fuel Trim and Lean/Rich Codes
3.1 OBD-II Standards and Communication
Key Takeaways Explain This Topic AI
The OBD-II J1962 connector is a 16-pin trapezoidal DLC where pin 4 is chassis ground, pin 5 is signal ground, and pin 16 is battery positive (B+).
All 2008 and newer US light-duty vehicles must use CAN per ISO 15765-4; earlier protocols include ISO 9141-2, KWP2000 (ISO 14230), and SAE J1850 VPW (GM) and PWM (Ford).
Diagnostic Trouble Codes follow a five-character P/B/C/U structure where the first letter identifies the system (Powertrain, Body, Chassis, Network) and the second character (0 or 1) flags generic SAE versus manufacturer-specific.
SAE J1979 defines the ten standard diagnostic services (modes $01-$0A) and the generic Parameter ID list every emissions-related ECM must support.
Recognizing pin assignments, protocol type, and DTC structure is required to answer L1 questions about scan-tool no-communication and code-interpretation scenarios.
Last updated: May 2026
OBD-II Standards and Communication
Quick Answer: OBD-II is the second-generation On-Board Diagnostic system standardized by the EPA and SAE. Every US-market light-duty vehicle since model year 1996 uses the same J1962 16-pin connector, a standardized set of diagnostic services (modes $01-$0A) , a standardized Parameter ID (PID) list defined by SAE J1979 , and a five-character DTC structure. Since model year 2008 , all light-duty vehicles must communicate over CAN (ISO 15765-4) .
OBD-II was mandated by the EPA to give technicians a uniform way to read emissions-related faults regardless of vehicle make. For the ASE L1 Advanced Engine Performance Specialist exam, you must be able to identify the physical connector , the electrical protocol the vehicle uses, and the structure of any DTC you read.
The J1962 Data Link Connector (DLC)
The SAE J1962 specification defines a 16-pin trapezoidal connector that must be located within two feet of the steering column and accessible without tools. Pins are numbered 1-8 across the top row and 9-16 across the bottom row.
- Pin Standard Function Notes
- 2 J1850 Bus+ (VPW or PWM) Used on GM VPW and Ford PWM
- 4 Chassis ground Bonded to the body
- 5 Signal ground Reference for protocol signals
- 6 CAN-H (High) ISO 15765-4
- 7 K-Line ISO 9141-2 / KWP2000
- 10 J1850 Bus- (PWM only) Ford only
- 14 CAN-L (Low) ISO 15765-4
- 15 L-Line ISO 9141-2 (rarely used after 2000)
- 16 Battery positive (B+) Powers the scan tool
Pins 1, 3, 8, 9, 11, 12, and 13 are reserved for manufacturer use. A vehicle that uses only CAN will typically have pins 4, 5, 6, 14, and 16 populated and pin 7 unused.
Communication Protocols
Five protocols are recognized by OBD-II. By 2008 all five except CAN were prohibited on new vehicles, but a technician working on used cars still encounters all of them.
- Protocol Standard Typical Vehicles Speed
- SAE J1850 VPW (Variable Pulse Width) SAE J1850 GM 1996-2005 10.4 kbps
- SAE J1850 PWM (Pulse Width Modulated) SAE J1850 Ford 1996-2004 41.6 kbps
- ISO 9141-2 ISO 9141-2 Asian and European 1996-2004 10.4 kbps
- KWP2000 ISO 14230-4 Asian and European 2003-2008 10.4 kbps
- CAN ISO 15765-4 All 2008+ US light-duty vehicles 250 or 500 kbps
CAN (Controller Area Network) uses a differential twisted pair (CAN-H on pin 6, CAN-L on pin 14). At rest, both lines sit near 2.5 V (recessive). During a dominant bit, CAN-H rises toward ~3.5 V and CAN-L drops toward ~1.5 V — the differential voltage is what carries the message, which is why CAN is highly resistant to electrical noise.
Diagnostic Services (Modes $01-$0A)
A scan tool talks to the ECM by requesting one of ten standard services defined by SAE J1979. The mode number is sent in hexadecimal, hence the $ prefix.
- Mode Service Why It Matters
- $01 Current powertrain data (live PIDs) Read RPM, coolant temp, MAF, fuel trim
- $02 Freeze frame data Snapshot taken when the most recent confirmed DTC set
- $03 Read stored (confirmed) DTCs The codes that turn on the MIL
- $04 Clear DTCs and freeze frame Resets all OBD-II monitors
- $05 Oxygen sensor monitoring test results Legacy on CAN vehicles, folded into $06
- $06 On-board monitor test results (non-continuous) Catalyst, EVAP, EGR, O2 heater test data
- $07 Pending DTCs Faults seen on the current or last drive cycle that have not yet matured
- $08 Bidirectional / actuator test Command the ECM to run an actuator
- $09 Vehicle information (VIN, calibration ID, CVN) Verifies the correct calibration is loaded
- $0A Permanent DTCs Cannot be cleared with a scan tool; only the ECM erases them after a successful drive cycle
- DTC Structure (Five Characters)
Every OBD-II Diagnostic Trouble Code is one letter followed by four hexadecimal digits . Character 1 Character 2 Characters 3-5
- ------------- ------------- ---------------
- P = Powertrain 0 = Generic System and
- B = Body 1 = Mfr-specif fault detail
- C = Chassis 2 = Generic (hexadecimal)
- U = Network 3 = Mfr-specif
P0xxx — SAE/EPA generic powertrain code. Same meaning on every brand.
P1xxx — Manufacturer-specific powertrain code. The number means whatever the OEM service information says it means.
B codes cover body modules (airbag, climate control, lighting).
C codes cover chassis modules (ABS, traction control, steering).
U codes cover network communication (lost-comm and bus faults — covered in §3.6).
Worked Example
A scan tool returns P0301 . Decode:
P = powertrain.
0 = generic.
3 = ignition system / misfire family.
01 = cylinder 1.
Result: Cylinder 1 misfire detected , same meaning on a Camry, an F-150, or a Silverado.
A scan tool returns P1345 on a GM small-block: this is manufacturer-specific ( P1xxx ) and means "Crankshaft-Camshaft Position Correlation". On a Ford, P1345 means something different. Always consult OEM service info for any P1 , P2 , B1 , C1 , or U1 code.