Study guide

9.4 T5 Wheels, Tires, and Hub Service

ASE Medium/Heavy Truck Certification Series T1–T8

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts and Series Structure 1.2 Fees, Scheduling, Experience, and Master Path 1.3 ASE Question Formats and Diagnostic Reasoning

2 T1 Gasoline Engines — Mechanical Systems

2.1 T1 General Engine Diagnosis 2.2 T1 Cylinder Head and Valve Train 2.3 T1 Engine Block Diagnosis and Repair 2.4 T1 Lubrication and Cooling Systems

3 T1 Gasoline Engines — Systems & Controls

3.1 T1 Ignition System Diagnosis and Repair 3.2 T1 Fuel, Air Induction, and Exhaust 3.3 T1 Emissions Control Systems 3.4 T1 Computerized Engine Controls (OBD II)

4 T2 Diesel Engines — Mechanical Systems

4.1 T2 Diesel General Engine Diagnosis 4.2 T2 Cylinder Head and Valve Train 4.3 T2 Engine Block Diagnosis and Repair 4.4 T2 Lubrication and Cooling Systems

5 T2 Diesel Engines — Fuel, Air & Brakes

5.1 T2 Air Induction and Exhaust Systems 5.2 T2 Diesel Fuel System Diagnosis and Repair 5.3 T2 Starting and Charging Systems 5.4 T2 Engine Brakes

6 T3 Drive Train

6.1 T3 Clutch Diagnosis and Repair 6.2 T3 Transmission Diagnosis and Repair 6.3 T3 Driveshaft and Universal Joints 6.4 T3 Drive Axle Diagnosis and Repair

7 T4 Brakes — Air Brake Systems

7.1 T4 Air Supply and Service Systems 7.2 T4 Foundation Brakes and Wheel Hubs 7.3 T4 Parking (Spring) Brakes

8 T4 Brakes — Hydraulic & Electronic

8.1 T4 Hydraulic Brakes Diagnosis and Repair 8.2 T4 ABS, ATC, ESC, and Collision Warning

9 T5 Suspension and Steering

9.1 T5 Steering System Diagnosis and Repair 9.2 T5 Suspension, Frame, and Fifth Wheel 9.3 T5 Wheel Alignment Diagnosis and Adjustment 9.4 T5 Wheels, Tires, and Hub Service

10 T6 Electrical — Core Systems

10.1 T6 General Electrical/Electronic Diagnosis 10.2 T6 Battery and Starting Systems 10.3 T6 Charging System Diagnosis and Repair

11 T6 Electrical — Lighting & Related

11.1 T6 Lighting Systems Diagnosis and Repair 11.2 T6 Related Vehicle Systems

12 T7 HVAC Systems

12.1 T7 HVAC Systems Diagnosis Overview 12.2 T7 A/C System and Component Diagnosis 12.3 T7 A/C Service, Recovery, and Leak Diagnosis 12.4 T7 Heating, Cooling Interface, and Controls

13 T8 PMI — Engine, Cab, Electrical

13.1 T8 Engine Systems PMI 13.2 T8 Cab and Hood PMI 13.3 T8 Electrical/Electronics PMI

14 T8 PMI — Chassis & Road Test

14.1 T8 Frame and Chassis PMI 14.2 T8 Road and Operational Test

15 Master Path & Study Strategy

15.1 Study Priority by Test Weight and Fleet Role 15.2 Master Path, Recertification, and Career Next Steps

9.4 T5 Wheels, Tires, and Hub Service

Key Takeaways Explain This Topic AI

T5 Area D (Wheels, Tires, and Hub Service) is about 9 scored questions (18%) covering dual matching, inflation and load ratings, tire wear causes, wheel fastener torque, hub lubrication (oil vs grease), seals, and damaged wheels.

Dual assemblies must match diameter/circumference and often tread design within fleet limits—mismatched duals scrub, overheat, and can destroy tires and differentials.

Inflation must follow load/inflation tables for the tire’s load range; both under- and over-inflation create distinct wear and failure risks.

Wheel nuts use OEM torque, sequence, and often a re-torque after initial service; wrong torque or paint-filled clamp faces cause loose wheels—catastrophic when duals walk off.

Hubs may be oil-bath or grease; never mix media. Seal leaks contaminate brakes; end-play adjustment (where applicable) protects bearings and ABS rings.

Last updated: July 2026

9.4 T5 Wheels, Tires, and Hub Service

Exam Focus: ASE T5 Area D is about 9 scored questions / 18% of the Suspension and Steering test. Master dual matching , inflation and load ratings , wear patterns , wheel fastener torque , hub oil vs grease , seal leaks , and damaged wheels . TPMS appears only at a high level where medium/heavy applications use it.

Wheels and tires are the only contact patches the truck has. A perfect alignment cannot save a dual set that is mismatched by a half-inch of rolling circumference, and a perfect kingpin job fails if the hub bearing is loose enough to destroy the seal and soak the brakes.

Tire Selection and Load Ratings

Commercial tires carry load range / ply rating and maximum load at a stated cold inflation. Fleet tires also use positions : steer, drive, trailer, and all-position.

Never exceed the wheel (rim) maximum pressure or load—the system limit is the lowest of tire, wheel, and axle capacity.

Use the tire manufacturer’s load/inflation table for actual axle loads—not only the sidewall maximum.

Mixing radial and bias on the same axle is improper; mixing sizes or brands on duals is restricted by policy and often by law/inspection practice.

Speed ratings and vocational compounds (refuse, construction, regional) matter for heat and wear; wrong application tires fail early even at “correct” pressure.

Inflation Discipline

Check pressures cold . Heat raises pressure; bleeding hot tires leads to chronic underinflation.

Condition Risks

Underinflation Both-shoulder wear, heat buildup, belt separation, blowout, poor fuel economy, overloaded carcass

  • Overinflation Center wear, harsh ride, impact breaks, reduced contact patch
  • Unequal across an axle Pull, uneven wear, dual scrub

Duals: measure both tires. A flat inner dual can go unnoticed until fire or disintegration. Use extension hoses or quality dual gauges; listen for leaks at valves and between duals.

Dual Matching

On drive and trailer duals, tires that differ in diameter or free circumference force the larger tire to drag the smaller (or scrub continuously).

Matching practices (training-level):

Pair tires with similar tread depth and measured circumference/diameter within fleet limit (often a small fraction of an inch—follow fleet/OEM).

Do not dual a new tire with a bald partner.

After matching, verify pressures equal.

Mismatched duals contribute to differential wear, power divider stress, and rapid tire destruction.

ASE may phrase this as “one dual is a different size” or “one tire has much more tread”—the fix is rematch/replace, not only alignment.

Tire Wear Patterns (Wheel/Tire Perspective)

Overlap with Area C, but Area D owns pressure, balance, damage, and dual issues :

  • Pattern / damage Likely cause
  • Both shoulders Underinflation / overload
  • Center Overinflation
  • Feathering Toe (send to alignment after pressure check)
  • Cupping Balance, shocks, runout, loose components
  • Flat spot Panic stop, locked brake, parking in one place with soft compound cold
  • Sidewall bulge / cut Impact or cut—remove from service
  • Exposed belts / steel Out of service immediately
  • Rapid inner dual wear Mismatch, debris between duals, bent wheel, alignment thrust

Debris between duals (rocks) must be removed—can cut sidewalls and start fires from friction heat.

Wheels: Types, Damage, and Runout

Common HD wheels: steel disc, aluminum disc; stud-piloted vs hub-piloted systems. Do not mix incompatible nut styles (two-piece flange nuts vs one-piece) with the wrong pilot system.

Inspect for

Cracks at hand holes, stud holes, and ring areas (multi-piece rims need extreme safety procedures—demount only with training).

Bent flanges and out-of-round from curb or pothole impact.

Corrosion under aluminum that frets clamp surfaces.

Improper repairs (welded cracks on wheels that are not repairable that way).

Lateral and radial runout beyond OEM/fleet limits causes vibration that drivers blame on balance or driveline. Measure before chasing U-joints. Bent wheels are replaced, not “trued” casually in the field.

Multi-piece rim safety

Side-ring and lock-ring designs store lethal energy when inflated. Always use cages/restraining devices per OSHA/fleet rules when inflating; never sit in the trajectory of a ring. T5 expects recognition that multi-piece rim service is specialized and dangerous—not a casual hammer job.

Wheel Fasteners and Torque

Loose wheels kill. Dual wheels that walk off separate at speed.

Best practices

Clean and inspect clamp faces of wheel and hub/drum—no dirt, excessive paint, or fretting that prevents clamp load.

Use correct nuts for hub-pilot vs stud-pilot systems; replace rounded or stretched fasteners.

Lubricate only as OEM allows (some hub-pilot systems specify dry threads or specific lube on pilot pads— follow the wheel manufacturer ).

Torque in a star/crisscross sequence in stages to the specified lb-ft.

Re-torque after 50–100 miles (or fleet interval) on new mounts—standard industry practice.

Never use impact wrenches as the final torque method unless a calibrated torque-limited process is approved; final check with a torque wrench.

  • Fault Result
  • Under-torque Loose wheel, elongated holes, stud shear
  • Over-torque Stretched studs, cracked wheels, false security
  • Wrong sequence Clamp uneven, runout, loose after road miles
  • Painted clamp face Loss of clamp as paint compresses

Broken studs: replace all studs in the hub if pattern suggests overload; check why (chronic loose running, wrong nuts).

Hubs: Oil vs Grease

Medium/heavy wheel ends are not all the same:

  • Type Identification / service
  • Oil-bath hub Sight window or fill plug; oil level at mark; gear-type or specified synthetic hub oil
  • Semi-fluid / grease-filled Packed or filled with specified grease quantity—not random chassis grease volume
  • Unitized / preset Often non-serviceable bearings; replace assembly when failed; follow OEM

Never pour gear oil into a grease-designed hub or pack heavy grease into an oil hub and call it done. Wrong media = bearing failure.

Bearing adjustment (serviceable designs)

Traditional adjustable bearings: seat the bearings while rotating, then back off to achieve OEM end play (often a few thousandths of an inch measured with a dial indicator).

  • Too tight → heat, blue hubs, seized bearings, possible wheel-off events in extreme cases
  • Too loose → roar, seal pound-out, ABS tone ring damage, irregular tire wear

Preset and unitized hubs eliminate field “castle nut feel” adjustment—use the OEM procedure only.

Seals

Hub seals keep oil/grease in and contaminants out. Leaks:

Oil on brakes → reduced braking, out-of-service risk—repair seal and service contaminated brakes (T4 territory).

Cause may be worn spindle, improper installation, excessive end play, or plugged axle breathers pushing oil out (drive axles).

Install seals with proper drivers; pre-lube lips; do not cock the seal in the bore.

Hubcaps (oil) must vent correctly; a failed window or gasket empties the hub on the road—drivers should catch this on pre-trip (T8 PMI overlap).

Vibration Isolation: Wheel/Tire vs Driveline

  • Clue Lean toward
  • Vibration vs road speed, changes with tire rotation Tire/wheel balance or runout
  • Vibration under load at certain RPM, driveline angles Driveshaft (T3) / ride height
  • Vibration after wheel install only Torque sequence, bent wheel, missing balance weights
  • Single-wheel hop Balance, roundness, suspension damping

Balance heavy truck assemblies with equipment rated for the tire/wheel mass. Note that some steer vibrations are radial force variation in the tire—replacement may be required when balance alone fails.

TPMS (High Level)

Some fleets and newer medium-duty platforms use tire pressure monitoring systems (internal sensors or external caps/valve systems).

Diagnose with OEM scan tools or system receivers; do not assume a dash warning is only a “bad module” without checking actual pressures.

Replace sensors carefully when demounting tires; torque sensor nuts to spec.

After tire service, relearn or ID sensors if the system requires it.

TPMS warns—it does not replace daily manual pressure checks in severe service.

ASE T5 will not require brand-specific sensor programming steps, but recognizing that a warning deserves pressure verification and system service awareness is enough.

Practical Service Workflow

Pre-trip style visual: cuts, inflation (gauge), debris between duals, hub oil level/leaks, loose nuts (indicators if used).

For vibration or wear: measure pressures, match duals, check runout/balance, then alignment referral.

For hub heat or noise: check lube type/level, end play, seals, and brakes for drag.

For wheel-off risk: torque audit, stud condition, pilot/clamp face cleanliness.

Document load range and pressure for the axle’s actual load.

Exam Strategy for Area D

Area D is practical and safety-heavy. Mismatched duals , wrong inflation for load , torque sequence/re-torque , oil vs grease hubs , and seal-soaked brakes are classic stems. If a hub is hot, think adjustment, lube, and brakes—not only “bad tire.” If vibration starts after a tire install, think bent wheel, balance, and fastener clamp before rebuilding the transmission. Connect dual matching to differential stress and you also reinforce T3 knowledge. Master these shop truths and the 9-question Area D slice becomes reliable points toward T5 certification.