Study guide
11.4 No-DTC Driveability Diagnosis
ASE T1 — Gasoline Engines Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & ASE T1 Exam Overview
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy
2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust
2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds
3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing
3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing
4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools
4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service
5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair
5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service
6 Chapter 5: Engine Block Diagnosis and Repair
6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection
7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair
7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators
8 Chapter 7: Ignition System Diagnosis and Repair
8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning
9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair
9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service
10 Chapter 9: Emissions Control Systems Diagnosis and Repair
10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures
11 Chapter 10: Computerized Engine Controls Diagnosis and Repair
11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation
11.4 No-DTC Driveability Diagnosis
Key Takeaways Explain This Topic AI
After an adequate soak, compare temperature PIDs with actual ambient conditions.
KOEO MAP should correspond to actual barometric pressure under the specified tolerance.
Normal idle data does not exclude fuel-delivery or ignition failure under load.
Last updated: October 2026
Note
No-DTC Driveability Diagnosis uses stated teaching examples. Actual pin assignments, dimensions, thresholds and procedures must come from the identified engine, component and diagnostic tool.
Diagnosing Driveability & Emissions Problems When NO DTCs Are Present (Task H.5)
A truck can suffer from hard starting, stalling, surging, black tailpipe smoke, or severe power loss with zero Confirmed, Pending, or Permanent DTCs and the MIL completely OFF . No-code driveability complaints fall into two primary categories:
1. In-Range Skewed Sensors (Fooling the PCM Without Crossing Circuit Limits)
The Comprehensive Component Monitor ( CCM ) flags an electrical circuit code only when a sensor's voltage drops near 0.0 V or climbs near 5.0 V , or when a cross-check monitor eventually fails. If a sensor drifts in-range , the PCM trusts the false reading and calculates the wrong fuel delivery and spark advance:
Skewed Engine Coolant Temperature ( ECT ) Sensor :
Stuck Reading Warm ( 165°F / 74°C ) on a Freezing Morning ( 30°F / -1°C ) : Because 165°F corresponds to a completely valid mid-range voltage ( ~1.1 V ), the CCM sets no DTC . However, when the driver cranks the freezing 30°F engine, the PCM believes the engine is already warm and omits cold-start fuel enrichment , causing a severe cold-start lean no-start, backfire through the intake, or repeated stalling until the engine physically warms up!
Stuck Reading Cold ( 55°F / 13°C ) When the Engine is Fully Hot ( 200°F / 93°C ) : The PCM keeps adding cold-start enrichment, delays Closed Loop operation, retards timing, and inhibits transmission overdrive and Torque Converter Clutch ( TCC ) lockup , causing terrible fuel economy, black smoke, and carbon-fouled spark plugs.
In-Range Contaminated Mass Airflow ( MAF ) Sensor : Dirt or oil film insulating the hot wire causes the MAF to under-report airflow under load ( WOT ) while reading slightly high at idle, starving the engine of fuel during heavy acceleration ( lean hesitation/pop ) before LTFT matures a two-trip code.
Skewed Barometric Pressure ( BARO ) Calculation : On trucks that calculate BARO from the MAP sensor at KOEO and WOT , a restricted air filter or skewed MAP sensor that convinces the PCM the truck is operating at 9,000 ft elevation ( 72 kPa ) when it is actually at sea level ( 101 kPa ) causes the PCM to trim base fuel pulse width lean across all load ranges.
2. Purely Mechanical, Hydraulic, or Secondary Ignition Faults
Many physical subsystems have no direct feedback sensor on certain medium-duty platforms:
Fuel Pressure / Volume Starvation or Contaminated Fuel : On returnless or mechanical-regulator fuel systems lacking a rail-mounted FRP sensor, a dying fuel pump or plugged filter that drops rail pressure from 58 psi to 34 psi under load causes severe power loss before setting a DTC. Likewise, phase-separated E10 / E15 water contamination or accidental diesel fuel contamination in the gasoline tank causes severe misfiring or a no-start with zero electrical faults.
Exhaust Backpressure & Valve Timing : A melted catalytic converter substrate ( >1.5–2.0 psi exhaust backpressure at idle, or >3.0 psi at 2,500 RPM ), a timing chain jumped by one tooth, or carbon-coked intake valve tulips restricts cylinder breathing without breaking any sensor wire.
The Mandatory KOEO Cold-Soak Rationality Check
Before starting the engine on any no-code driveability complaint, connect the scan tool in Key-On Engine-Off ( KOEO ) after the truck has cooled overnight and compare four temperature PIDs and two pressure PIDs:
ECT , IAT , Engine Oil Temperature (EOT) , and Transmission Fluid Temperature (TFT) should agree within the OEM's cold-soak tolerance; ±3°F to ±5°F is the stated example range of each other and match ambient shop temperature!
MAP must equal BARO ( ~29.9 in. Hg / 101 kPa at sea level, decreasing by approximately 1.0 in. Hg / 3.4 kPa for every 1,000 ft of altitude), and TPS / APP should follow the specified smooth relationship; a generic PID need not display a literal 0%–100% range without dropouts.
Tip
Worked Diagnostic Scenario — Cold-Start Stall with Zero DTCs: A municipal fleet 6.0L V8 snowplow truck cranks and starts on a 25°F morning, immediately stumbles, pops through the intake plenum, and stalls three times before finally staying running after 3 minutes of warming up. No DTCs ( Mode \$03 , \$07 , or \$0A ) are stored. Before cranking the cold engine the next morning, the technician performs a KOEO cold-soak rationality check : IAT = 28°F , EOT = 27°F , TFT = 27°F , MAP = 100 kPa , BARO = 100 kPa , but ECT = 158°F ( 1.22 V ) . Because 158°F is a completely normal in-range voltage, the PCM set no circuit code—yet it withheld cold-start fuel enrichment on a 28°F block! Replacing the internally drifted ECT thermistor restores 28°F KOEO agreement and eliminates the cold-start stall.
Applied Diagnostic Check
A no-code test benefits from comparing two reproducible states. For a cold-only concern, record the overnight baseline before starting, then the same PIDs after warming. For a load-only concern, record a safe idle baseline and the driver-reported demand condition. Keep sensor units and controller source consistent. A warmed-up check cannot reproduce a poor cold-soak input, and a stationary rev does not automatically reproduce a loaded grade. Note what remained untested if the conditions cannot be safely duplicated. That limit determines the next diagnostic step rather than proving the vehicle has no fault.