Study guide
11.1 DTC States and MIL Operation
ASE T1 — Gasoline Engines Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & ASE T1 Exam Overview
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy
2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust
2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds
3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing
3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing
4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools
4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service
5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair
5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service
6 Chapter 5: Engine Block Diagnosis and Repair
6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection
7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair
7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators
8 Chapter 7: Ignition System Diagnosis and Repair
8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning
9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair
9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service
10 Chapter 9: Emissions Control Systems Diagnosis and Repair
10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures
11 Chapter 10: Computerized Engine Controls Diagnosis and Repair
11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation
11.1 DTC States and MIL Operation
Key Takeaways Explain This Topic AI
A flashing MIL warns of a catalyst-damaging misfire and requires prompt load reduction.
Pending and confirmed codes represent different stages of fault detection.
A scan-tool clear command cannot directly erase a supported permanent code.
Last updated: October 2026
Note
Trip logic, monitor conditions and the readiness case in this lesson are teaching examples, not a service specification for every T1 truck. Use the identified engine, component and tool manufacturer's procedure and limits when making a repair decision.
OBD-II System Operation, Enable Criteria, Monitors, Freeze Frame & Drive Cycles
Modern medium- and heavy-duty gasoline trucks rely on On-Board Diagnostics Generation II ( OBD-II ) and Heavy-Duty On-Board Diagnostics ( HD-OBD ) standards ( SAE J1979 and SAE J2012 ) to continuously supervise exhaust and evaporative emissions. Whenever an emission-related component or subsystem degrades beyond regulatory thresholds—under monitor-specific thresholds that depend on vehicle class, model year and applicable rules—the Powertrain Control Module ( PCM ) logs a standardized Diagnostic Trouble Code ( DTC ) , captures a snapshot of operating parameters, and alerts the driver via the Malfunction Indicator Lamp ( MIL ) .
Decoding 5-Character Alphanumeric OBD-II DTCs (Tasks H.1, H.2)
Every SAE J2012 trouble code consists of a five-character alphanumeric string that identifies the vehicle domain, code standardization authority, subsystem category, and specific fault condition:
Character Position Code Values Technical Meaning & Subsystem Breakdown
1st Character (System Prefix) P , B , C , U P = Powertrain (engine, ignition, fuel, emissions, transmission); B = Body (cab, HVAC, supplemental restraints); C = Chassis (ABS, traction/stability control, suspension); U = Network Data Communication ( CAN , SAE J1939 , LIN ).
2nd Character (Standard vs. OEM) 0 , 1 , 2 , 3 0 = SAE generic/global code with an identical definition across all manufacturers; 1 = Manufacturer-specific ( OEM -defined) code; 2 & 3 = SAE -controlled or OEM -reserved expanded groupings depending on prefix.
3rd Character ( P -Code Subsystem) 1 through 8 1 & 2 = Fuel and Air Metering ( P01xx – P02xx ); 3 = Ignition System or Cylinder Misfire ( P03xx ); 4 = Auxiliary Emissions Controls ( EGR , EVAP , Catalyst, AIR — P04xx ); 5 = Vehicle Speed, Idle Control & Auxiliary Inputs ( P05xx ); 6 = Computer & Output Circuits ( P06xx ); 7 & 8 = Transmission Controls ( P07xx – P08xx ).
4th & 5th Characters (Fault Index) 00 to 99 (or hex 00 – FF ) Identifies the exact sensor, actuator, cylinder, or rationality failure (for example, P0306 = Cylinder 6 Misfire Detected; P0118 = Engine Coolant Temperature Sensor 1 Circuit High).
Type A vs. Type B Fault Maturation, Pending ( Mode \$07 ) & Permanent ( Mode \$0A ) Codes
Not all faults command the MIL on at the same time. The PCM classifies emission faults by severity and trip count:
Type A DTCs (Single-Trip Severe Faults) : Assigned to high-impact emission or powertrain failures—such as a severe misfire, throttle actuator control fault, or open/short circuit on a primary engine sensor ( ECT , MAP , MAF , CKP , TPS ). When a Type A monitor fails during the very first drive trip , the PCM immediately illuminates the MIL , stores a Confirmed/Active DTC ( Mode \$03 ) , and records Freeze Frame ( Mode \$02 ) data.
Flashing / Blinking MIL ( 1 Hz ) : If the PCM detects an active Type A catalyst-damaging misfire (where raw unburned fuel and oxygen are entering the exhaust and threatening to overheat the catalytic converter substrate past 1,600°F – 2,000°F ), it flashes the MIL once per second ( 1 Hz ). The driver must immediately reduce engine load and throttle opening. Once the misfire drops below the catalyst-damage threshold, the MIL reverts to steady illumination.
Type B DTCs (Two-Trip Emission Faults) : Assigned to less immediate emission faults such as Catalyst Efficiency ( P0420 / P0430 ) , Evaporative ( EVAP ) System Leaks ( P0442 / P0455 ) , or EGR Insufficient Flow ( P0401 ) .
Trip 1 ( Pending DTC — Mode \$07 ) : On the first trip in which the monitor runs and fails, the PCM keeps the MIL OFF and stores a Pending DTC ( Mode \$07 ) . If the monitor runs and passes on the very next trip, the PCM erases the Pending code automatically.
Trip 2 ( Confirmed DTC — Mode \$03 ) : Only if the monitor fails again on a second consecutive drive trip does the PCM mature the code into a Confirmed/Active DTC ( Mode \$03 ) , illuminate the steady MIL , and store Freeze Frame ( Mode \$02 ) data.
Permanent DTCs ( Mode \$0A , SAE J1979 ) : On applicable OBD-equipped vehicles that support permanent codes, a Permanent DTC is mirrored into non-volatile random-access memory ( NVRAM ) when a supported emission DTC meets the permanent-storage criteria and illuminates the MIL . Unlike Mode \$03 or Mode \$07 codes, a Permanent DTC ( Mode \$0A ) cannot be erased with a scan tool "Clear Codes" command ( Mode \$04 ) or by disconnecting the vehicle batteries . This prevents operators from clearing codes right before an emissions inspection without fixing the truck. The PCM erases a Mode \$0A Permanent DTC only after it executes and passes the specific diagnostic monitor that originally set the fault during a valid drive cycle.
Self-Extinguishing MIL vs. History Code Clearing :
Turning Off the MIL ( 3 Good Trips ) : If an intermittent fault repairs itself or stops occurring, the PCM turns off the MIL after 3 consecutive good drive trips in which the monitor passes. For Misfire and Fuel System faults, those 3 passing trips must occur under similar operating conditions —specifically within ±375 RPM of the original fault speed, within ±20% calculated engine load , and at the same engine warm-up status ( cold vs. warm ) captured in Freeze Frame.
Erasing the History DTC ( 40 Warm-Up Cycles ) : After the MIL self-extinguishes, the code remains in PCM history memory until the vehicle completes the applicable warm-up aging period, often 40 cycles without the fault recurring. A valid warm-up cycle requires engine coolant temperature ( ECT ) to rise by at least 40°F ( 22°C ) from engine start-up and reach a minimum of 160°F ( 71°C ) .
Important
Never Clear DTCs Before Recording Freeze Frame ( Mode \$02 ) and Mode \$06 Data: Sending a scan tool Clear Codes ( Mode \$04 ) command immediately wipes out Freeze Frame ( Mode \$02 ) , clears Pending ( Mode \$07 ) and Confirmed ( Mode \$03 ) codes, may reset Mode \$06 results, depending on implementation (such as per-cylinder misfire history), can affect learned data, but fuel-trim/KAM reset may require a separate OEM command, and resets all non-continuous readiness monitors to NOT READY / INCOMPLETE . Always save or print the complete scan report prior to clearing codes.
Applied Diagnostic Check
A fault class and its warning behavior must be taken from the actual diagnostic definition. The letters Type A and Type B are useful descriptions on systems that use them, but not every sensor code belongs to a universal first-trip group. Separate the emission MIL from a reduced-power or other dashboard warning. Preserve both generic and enhanced records where available. A pending record can show an event before confirmation, and the absence of a permanent record can reflect support or storage criteria. Report the status actually read rather than adding a status inferred from a generic code list.