Study guide

11.2 Readiness, Freeze Frame and Repair Verification

ASE T1 — Gasoline Engines Medium/Heavy Truck

Track your progress as you read

Finished sections get a check mark.

1 Introduction & ASE T1 Exam Overview

1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy

2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust

2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds

3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing

3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing

4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools

4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service

5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair

5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service

6 Chapter 5: Engine Block Diagnosis and Repair

6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection

7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair

7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators

8 Chapter 7: Ignition System Diagnosis and Repair

8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning

9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair

9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service

10 Chapter 9: Emissions Control Systems Diagnosis and Repair

10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures

11 Chapter 10: Computerized Engine Controls Diagnosis and Repair

11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation

11.2 Readiness, Freeze Frame and Repair Verification

Key Takeaways Explain This Topic AI

Save freeze-frame and monitor results before a reset can remove evidence.

Continuous monitors also have enabling or suspension conditions.

A monitor pass and the required aging conditions govern permanent-code clearing.

Last updated: October 2026

Note

Readiness, Freeze Frame and Repair Verification uses stated teaching examples. Actual pin assignments, dimensions, thresholds and procedures must come from the identified engine, component and diagnostic tool.

Continuous vs. Non-Continuous Readiness Monitors, Freeze Frame ( Mode \$02 ) & Mode \$06 (Tasks H.1, H.2, H.11)

OBD-II divides system self-tests into three Continuous Monitors and the supported Non-Continuous Readiness Monitors:

Monitor Classification Specific OBD-II Monitors Included Execution Frequency & Diagnostic Function

Continuous Monitors (3 Total) 1. Misfire Monitor ( CKP acceleration variance); 2. Fuel System Monitor ( STFT / LTFT authority limits); 3. Comprehensive Component Monitor ( CCM ) Run repeatedly when the relevant enabling conditions are met; rough-road or other conditions can suspend a monitor. The CCM checks electrical inputs and outputs for opens, shorts to ground, shorts to voltage, and basic rationality.

Non-Continuous Monitors (Gasoline Spark-Ignition) 1. Catalyst Efficiency ; 2. Heated Catalyst ; 3. Evaporative ( EVAP ) System ; 4. Secondary Air Injection ( AIR ) ; 5. Oxygen ( O2 / A/F ) Sensor ; 6. Oxygen Sensor Heater ; 7. EGR and/or VVT System Run at their calibrated frequency (or during an engine-off soak) only after strict Enable Criteria are satisfied . Display status as READY / COMPLETE or NOT READY / INCOMPLETE (or UNSUPPORTED ).

Interpreting Freeze Frame ( Mode \$02 ) and Mode \$06 Test Data

Freeze Frame ( Mode \$02 ) : Captures a single-moment snapshot of engine PIDs at the recorded fault event under the implementation's storage rules: Engine RPM , Calculated Load % , ECT , IAT , MAP / MAF , STFT and LTFT (Bank 1 & Bank 2) , Vehicle Speed (VSS) , Fuel Rail Pressure (FRP) , and Fuel System Status ( Closed Loop vs. Open Loop ) . This tells the technician how to duplicate the complaint : for example, if P0171 ( System Too Lean Bank 1 ) set at 680 RPM , 18% Load , 0 mph , and +28% LTFT , the fault is an intake manifold vacuum leak (which affects idle most severely). Conversely, if P0171 set at 3,800 RPM , 88% Load , 62 mph , and +26% LTFT while idle fuel trims are near 0% , the fault is fuel delivery starvation under high fuel demand (weak fuel pump, plugged fuel filter, or under-reporting MAF sensor).

Freeze Frame Overwrite Priority : Standard Mode \$02 memory holds one Freeze Frame snapshot. A Type A misfire or fuel system DTC automatically overwrites an existing lower-priority Type B Freeze Frame record.

Mode \$06 (On-Board Monitoring Test Results) : Displays the raw engineering test values and minimum/maximum pass/fail limits that each monitor measured during its latest evaluation. Technicians use Mode \$06 ( Monitor ID \$A1 – \$AC for Misfire Data) to identify which specific cylinder is intermittently misfiring (comparing Exponentially Weighted Moving Average [ EWMA ] 10-trip misfire counts and last-driving-cycle misfire counts) even when the misfire rate has not yet crossed the Mode \$03 DTC threshold, or to see how close a catalytic converter's oxygen storage index is to failing after a repair.

Performing an OBD-II Drive Cycle to Verify Repairs and Reset Monitors (Task H.11)

After repairing an emissions or driveability fault, you cannot simply start the truck in the service bay, observe that the MIL is off, and release the vehicle. If the repaired monitor is still INCOMPLETE , the PCM has not yet tested the circuit—and any Permanent DTC ( Mode \$0A ) will remain stored.

Step-by-Step Drive Cycle Verification Procedure

Execute the Actual OEM Drive Trace: Obtain the trace for the engine and monitor being verified. Soak, speed, load and deceleration intervals vary. Use a safe route or permitted test facility; obey traffic conditions and never omit necessary braking to complete a monitor. Some EVAP tests run after shutdown, so a warm shop idle or a generic highway trip may not exercise them.

Tip

Worked Diagnostic Scenario — Why a Replaced EVAP Purge Valve Failed to Clear P0455 ( Mode \$0A ): A fleet technician replaces a stuck-open EVAP canister purge valve on a 2019 Class 5 gasoline service truck with stored P0455 ( EVAP System Large Leak Detected ), clears the codes with a scan tool, and road-tests the truck for 20 minutes. Upon return, Mode \$03 is empty and the MIL is off, but the state inspection computer rejects the truck because P0455 is still present as a Permanent DTC ( Mode \$0A ) and the EVAP monitor reads INCOMPLETE . Checking live PIDs reveals Fuel Level = 96% (the driver filled the tank to the brim before bringing the truck to the shop) and start-up ECT was 188°F . Because the EVAP monitor requires a cold soak ( ECT < 122°F within 10°F of IAT ) and a fuel level between 15% and 85% , the monitor was blocked from running! Draining/consuming fuel down to 60% , allowing an overnight cold soak, and executing the OEM cold-start drive trace allows the EVAP monitor to run, transition to COMPLETE , and satisfy the required monitor passes and aging conditions before the PCM can erase the permanent code.

Source Check — October 13, 2026

California BAR distinguishes readiness, permanent codes and vehicle-specific inspection exceptions; inspection acceptance depends on the actual jurisdiction. Manufacturer or regulator reference .

A Complete Repair-Verification Record

Start with the actual fault and the tests that originally supported it. Repeat the physical check after repair: pressure, flow, voltage drop, waveform or leakage as appropriate. Then review current and pending codes and the supported monitor status. Unsupported means the vehicle does not report that monitor; incomplete means a supported test has not completed. A complete monitor can record a failure, so readiness alone is not a passing result.

Use the published enable criteria for the particular monitor. Record fuel level, startup temperature, ambient conditions and any inhibiting faults that prevented execution. A cold-start monitor may need a soak, while an engine-off test may need the specified preceding drive and time after shutdown. Do not promise that one generic drive cycle clears every permanent code. Several passing evaluations or additional aging conditions can be required.

Distinguish technical verification from local inspection acceptance. The inspection program may use its own supported-monitor allowances, permanent-code rules and vehicle exceptions. Document the monitor result and remaining limitations accurately. If a permanent code persists after the repair is physically confirmed, consult the OEM clearing logic and applicable inspection guidance instead of replacing another part solely to remove the record.

Loading diagram... OBD-II Fault Maturation, Readiness Monitor Execution & Permanent DTC Clearing Flow