Study guide
11.3 Service Literature and Diagnosis with DTCs
ASE T1 — Gasoline Engines Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & ASE T1 Exam Overview
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy
2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust
2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds
3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing
3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing
4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools
4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service
5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair
5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service
6 Chapter 5: Engine Block Diagnosis and Repair
6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection
7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair
7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators
8 Chapter 7: Ignition System Diagnosis and Repair
8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning
9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair
9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service
10 Chapter 9: Emissions Control Systems Diagnosis and Repair
10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures
11 Chapter 10: Computerized Engine Controls Diagnosis and Repair
11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation
11.3 Service Literature and Diagnosis with DTCs
Key Takeaways Explain This Topic AI
Identify the correct connector face and pin before applying a circuit test.
Rationality codes can involve a physical system as well as a sensor.
Interrelated controllers can request torque reduction or prevent engine operation.
Last updated: October 2026
Note
Diagnostic chart thresholds, cold-soak tolerances and network examples in this lesson are teaching examples, not a service specification for every T1 truck. Use the identified engine, component and tool manufacturer's procedure and limits when making a repair decision.
Technical Literature & Driveability Diagnosis With and Without DTCs
Accurate computerized engine control diagnosis requires combining OEM service information with disciplined root-cause analysis. One of the costliest mistakes in heavy-truck repair is treating a diagnostic trouble code as a parts-replacement instruction. A DTC never condemns a specific component —it only reports that a voltage, frequency, current, or calculated rationality relationship across an entire circuit ( sensor + connector terminals + wiring harness + splice packs + PCM driver/input + mechanical system ) violated a programmed threshold.
Using OEM Service Information & Step-by-Step Diagnostic Trees (Task H.3)
Before touching a multimeter lead to a truck, technicians must consult four core sections of OEM technical literature:
Technical Service Bulletins ( TSBs ) and Recall Campaigns : Always search TSBs by symptom and DTC first . If a truck exhibits a cold-start hesitation, false P0300 misfire, or throttle body icing issue caused by a known PCM calibration bug or updated wiring harness routing, OEM engineers have already documented the revised part number or SAE J2534 flash calibration.
DTC Enabling Conditions & Diagnostic Flowcharts : OEM code charts specify the exact electrical or mathematical condition required to set a code ( Set Condition ) and guide the technician through isolating the sensor from the wiring harness and the PCM .
Connector End Views & Pinout Charts : Show the exact cavity numbering, wire insulation color/tracer stripe, circuit identification number, and normal Key-On Engine-Off ( KOEO ) and Key-On Engine-Running ( KOER ) pin voltages or oscilloscope waveforms.
Distinguishing Circuit Electrical Codes vs. Range/Performance Rationality Codes :
Circuit Low / Circuit High Electrical Codes (e.g., P0107 MAP Circuit Low <0.2 V or P0108 MAP Circuit High >4.8 V ) : Triggered by the CCM when the signal voltage falls outside the normal 0.5 V–4.5 V operating window due to an open wire, terminal fretting corrosion, short to ground, short to voltage, missing 5.0 V reference, or internal sensor break.
Range/Performance / Rationality Codes (e.g., P0106 MAP Range/Performance or P0101 MAF Range/Performance) : The signal voltage is completely within the valid 0.5 V–4.5 V electrical range, so the wiring continuity is usually intact. Instead, the PCM cross-checks MAP , Throttle Position ( TP ) , Engine Speed ( RPM ) , and Mass Airflow ( MAF ) against a physical volumetric-efficiency model. If the engine is idling at 650 RPM with the throttle closed ( TP = 8% ), manifold pressure should be 30–38 kPa ( 18–21 in. Hg vacuum). If MAP actually reads 68 kPa ( 9 in. Hg vacuum), the PCM sets P0106 . Replacing the MAP sensor will not fix the truck if the real cause of the low manifold vacuum is a jumped timing chain , severe intake vacuum leak , restricted catalytic converter , or carbon-plugged MAP reference port !
Warning
Never Front-Probe Sealed Weather-Pack or Metri-Pack Terminals: Forcing a standard DMM probe tip into the mating face of a female PCM or sensor terminal spreads the contact tangs apart, creating an intermittent open circuit ( terminal fretting or poor pin tension) weeks later. Always use proper back-probing pins along the wire seal or OEM breakout test leads ( J-35616 style) when measuring circuit voltages.
Diagnosing Driveability & Emissions Problems From Interrelated Vehicle Systems With DTCs (Task H.4)
On modern medium- and heavy-duty trucks, the PCM shares a high-speed CAN / SAE J1939 network with the transmission, braking, cab, climate control, and security modules. Faults in these interrelated systems routinely cause the PCM to restrict engine power, alter idle speed, or disable fuel injection:
Interrelated Vehicle System Typical Fault Condition & Associated DTCs Resulting Engine Driveability / Emissions Symptom
Automatic Transmission ( TCM ) & Torque Management Slipping clutch pack, failed Turbine/Output Shaft Speed sensor ( P0715 , P0720 ), shift solenoid fault, or generic P0700 ( TCM MIL Request) TCM commands PCM torque reduction via CAN (limiting Electronic Throttle Control [ ETC ] opening and retarding spark) and locks the transmission into 2nd or 3rd gear limp-in mode ; driver complains of "no engine power pulling away from a stop" and high RPM at highway speed.
Traction Control ( TCS ), ESC & ABS Wheel Speed Rusted/cracked wheel speed sensor tone ring, excessive sensor air gap from a loose wheel bearing, or mismatched tire sizes ( C0035 – C0050 ) ABS/ESC module detects false wheel slip on dry pavement and sends a CAN torque-reduction request to the PCM , which closes the electronic throttle and retards ignition timing—feeling like an intermittent engine stumble or misfire under acceleration.
Air Conditioning ( A/C ) High-Pressure / Compressor Load Overcharged A/C refrigerant ( >400–450 psi high side), failed condenser fan, or internally seizing A/C compressor ( P0530 – P0534 ) Extreme parasitic torque load drags down curb idle RPM, triggers violent idle surge, or stalls the engine whenever the A/C compressor clutch engages; high-pressure sensor input can also command cooling fans to 100% duty cycle and inhibit A/C operation.
Theft Deterrent / Immobilizer ( PATS / Passkey ) Unprogrammed transponder key, damaged ignition lock exciter ring, or lost CAN security handshake between BCM and PCM ( B2799 , P1260 , P0513 ) Produces either a no-crank condition (starter relay ground inhibited) or a classic 1-to-2 second start-and-stall where the engine fires briefly on prime pulses and dies immediately because the PCM disables fuel injector pulse width and/or spark without the encrypted security fuel-enable password.
Cruise Control & Stationary PTO Interlocks Misadjusted or stuck Brake Pedal Position ( BPP ) switch ( P0504 , P0571 ), faulty clutch pedal switch, or erratic Vehicle Speed Sensor ( VSS ) ( P0500 ) PCM refuses to engage highway cruise control or immediately drops out of Stationary Power Take-Off ( PTO ) elevated-idle RPM mode when powering hydraulic utility beds, aerial buckets, or dump bodies.
Applied Diagnostic Check
A security-related start-and-stall diagnosis should include the immobilizer and body-controller records, not only powertrain Modes 03 and 07. Confirm the key recognition and permitted-start status while observing the lost injector or spark command. Normal rail pressure narrows the possibilities but does not prove a security failure by itself. Likewise, a torque-reduction request requires evidence from the requesting module and the matching engine response. Save those records together. This distinguishes an interrelated-system instruction from a local engine fault that happened to produce a similar loss of power at the same moment.
Following a Diagnostic Chart Without Losing Context
Confirm the exact engine, calibration and connector view before following a pinpoint chart. Note whether a view is from the harness or component face; reversing the view can send a jumper or meter lead to the wrong cavity. Verify that the chart's entry conditions match the actual code and symptom. A diagnostic step that assumes a proven supply or ground is not valid when that earlier check was skipped.
Record the result of each decision and why the next step follows. If a measurement conflicts with the rest of the evidence, check probe contact, units, range and operating state before concluding that the module must be faulty. An intermittent complaint may require recording data or reproducing a thermal or vibration condition. After the identified fault is repaired, return to the beginning of the concern and confirm that the original symptom and the affected code-monitor conditions are resolved.