Study guide
10.4 Catalyst Oxygen Storage and Five-Gas Analysis
ASE T1 — Gasoline Engines Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & ASE T1 Exam Overview
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy
2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust
2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds
3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing
3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing
4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools
4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service
5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair
5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service
6 Chapter 5: Engine Block Diagnosis and Repair
6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection
7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair
7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators
8 Chapter 7: Ignition System Diagnosis and Repair
8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning
9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair
9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service
10 Chapter 9: Emissions Control Systems Diagnosis and Repair
10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures
11 Chapter 10: Computerized Engine Controls Diagnosis and Repair
11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation
10.4 Catalyst Oxygen Storage and Five-Gas Analysis
Key Takeaways Explain This Topic AI
A catalyst can age as well as suffer poisoning, overheating or fracture.
A flat rear oxygen trace alone does not establish catalyst health.
Lambda uses fuel and gas-analysis assumptions; equal CO and O2 is not a universal stoichiometric rule.
Last updated: October 2026
Note
Catalyst Oxygen Storage and Five-Gas Analysis uses stated teaching examples. Actual pin assignments, dimensions, thresholds and procedures must come from the identified engine, component and diagnostic tool.
- Three-Way Catalytic Converter (TWC) Chemistry, P0420 / P0430 & Failure Root Causes (Tasks G.6, G.8)
- Dual-Stage TWC Chemical Reactions & Oxygen Storage Capacity ( OSC )
A modern Three-Way Catalytic Converter ( TWC ) uses a honeycomb ceramic (cordierite) or metallic monolith coated with an aluminum oxide ( Al2O3 ) and cerium oxide ( CeO2 ) washcoat impregnated with precious group metals:
Reduction Function ( Rhodium [Rh] & Platinum [Pt] ): Strips oxygen atoms from oxides of nitrogen ( NOx : NO and NO2 ) , reducing them into harmless nitrogen gas ( N2 ) and oxygen ( O2 ). Crucial Rule: Chemical reduction of NOx works efficiently only when the exhaust stream is at exact stoichiometry ( 14.7:1 , λ = 1.00 ) or slightly rich ( λ = 0.99 ), because excess free oxygen in a lean exhaust stream prevents Rh from stripping oxygen off NOx .
Oxidation Function ( Platinum [Pt] & Palladium [Pd] ) + Cerium Oxide ( CeO2 ): Uses oxygen to oxidize unburned Hydrocarbons ( HC ) and Carbon Monoxide ( CO ) into harmless water vapor ( H2O ) and carbon dioxide ( CO2 ). Because the PCM constantly switches the air-fuel mixture slightly rich and slightly lean around 14.7:1 , the cerium oxide ( CeO2 ) coating acts as a rechargeable oxygen capacitor (Oxygen Storage Capacity, OSC ) —absorbing and storing excess O2 during momentary lean swings and releasing stored O2 during momentary rich swings so HC and CO oxidation continues without interruption.
Interpreting P0420 (Bank 1) and P0430 (Bank 2) Catalyst Efficiency Waveforms
Healthy Catalyst Waveform: At a steady 2,000 RPM warm closed-loop cruise, the upstream HO2S11 sensor switches rapidly between 0.10 V and 0.90 V ( 1 to 3 Hz ) as it regulates fuel trim. Because a healthy catalyst's CeO2 washcoat absorbs and consumes the fluctuating oxygen, the downstream HO2S12 sensor sees an oxygen-depleted, buffered exhaust stream and outputs a nearly flat, steady line between 0.60 V and 0.75 V .
Failed Catalyst Waveform ( P0420 / P0430 ): When thermal degradation or chemical poisoning destroys the catalyst's Oxygen Storage Capacity ( OSC ), oxygen fluctuations pass straight through the converter unchanged. The downstream HO2S12 voltage waveform begins mirroring the rapid switching frequency and amplitude of the upstream HO2S11 sensor . When the OBD-II Mode \$06 catalyst monitor calculates that the downstream-to-upstream switching ratio (or OSC delay time during a fuel-cut test) has degraded past the threshold, it sets P0420 (Bank 1) or P0430 (Bank 2) .
Root Causes of Catalyst Failure & Exhaust Backpressure Testing
A catalytic converter is a passive chemical reactor with no moving parts—it can lose activity through normal thermal aging as well as contamination, overheating or physical damage. Before replacing a failed converter, technicians must always correct the upstream engine fault that killed it:
Thermal Meltdown ( >1,800°F–2,000°F ): Caused by raw fuel + oxygen entering the converter from an ignition misfire ( P0300–P0310 ) , a leaking fuel injector, a stuck-open EVAP purge valve, or a false-lean upstream HO2S /exhaust leak. The ceramic monolith melts into a glassy restriction that chokes exhaust flow. Verify with an exhaust backpressure gauge threaded into the upstream HO2S11 port: normal backpressure is <1.0 to 1.5 psi at idle and <2.5 to 3.0 psi at 2,500 RPM .
Chemical Poisoning / Washcoat Glazing: Caused by burning engine oil ( phosphorus and zinc ZDDP anti-wear additives glaze the washcoat), internal engine coolant leaks ( antifreeze silicates ), or using non-sensor-safe RTV silicone sealant.
Thermal Shock / Mechanical Fracture: Caused by splashing through deep cold water puddles under heavy load or broken exhaust hangers allowing road impacts to crack the brittle ceramic brick.
Five-Gas Exhaust Analyzer & Lambda ( λ ) Diagnostics (Task G.9)
Exhaust Gas / Parameter Unit Normal Stoichiometric Pre-Cat ( λ = 1.00 ) Normal Post-Cat (Healthy TWC) Primary Diagnostic Meaning When Abnormal
Hydrocarbons ( HC ) ppm 50 to 150 ppm <20 to 50 ppm Unburned raw fuel. High HC ( >300–1,500 ppm ) indicates an ignition misfire, lean misfire, burned exhaust valve, or low cylinder compression .
Carbon Monoxide ( CO ) % ~0.4% to 0.6% <0.05% to 0.10% Partially burned fuel — direct rich indicator. High CO ( 2.0% to 6.0%+ ) always supports a rich air-fuel mixture ( λ < 1.00 ) .
Carbon Dioxide ( CO2 ) % 13.5% to 14.5% 14.5% to 15.5% Combustion & catalyst efficiency indicator. Peak CO2 occurs only at λ = 1.00 . Reading <12.5% indicates poor combustion or an exhaust dilution leak .
Oxygen ( O2 ) % ~0.4% to 0.6% 0.1% to 0.5% Leftover unburned oxygen — lean / misfire / leak indicator. Notice that these are illustrative pre-catalyst values, not a rule that CO and O2 must be equal at stoichiometry
Oxides of Nitrogen ( NOx ) ppm 500 to 1,200 ppm <50 to 100 ppm Formed when peak cylinder temp >2,500°F . High NOx indicates inoperative EGR ( P0401 ), slightly lean mixture, over-advanced timing, overheating, or failed TWC reduction bed .
Lambda ( λ ) Ratio 1.00 ( 14.7:1 gasoline) 1.00 Calculated principally from HC, CO, CO2 and O2, with the fuel composition assumed by the analyzer ( Brettschneider equation ). λ < 1.00 = Rich ( e.g., 0.90 ); λ > 1.00 = Lean ( e.g., 1.12 ).
Tip
Distinguishing Misfire vs. Rich vs. Lean on a 5-Gas Analyzer:
Ignition or Compression Misfire: Sky-high HC ( >800 ppm ) + high O2 ( >2.5% ) + very low CO ( <0.15% ) + low CO2 ( <11.5% ) . Why? Because the spark plug never lit the charge, both raw fuel ( HC ) and unburned air ( O2 ) were pumped straight out the exhaust valve without forming CO or CO2 !
Rich Air-Fuel Mixture: High CO ( 3.5% ) + moderately high HC ( 300 ppm ) + near-zero O2 ( 0.05% ) + low CO2 ( 11.8% ) ( λ = 0.89 ). Every oxygen molecule was consumed, leaving partially oxidized CO .
Lean Air-Fuel Mixture: High O2 ( 2.2% ) + near-zero CO ( 0.02% ) ( λ = 1.08 ), with HC spiking sharply as soon as the mixture becomes too lean to ignite reliably (lean misfire).
Worked Example: Diagnostic Scenario: Five-Gas Analysis on a Heavy-Duty V10 Truck
Concern: A Class 6 municipal dump truck with a 6.8L V10 fails a tailpipe emissions inspection at 2,000 RPM steady cruise with the following post-catalyst 5-gas readings: HC = 18 ppm , CO = 0.03% , CO2 = 15.1% , O2 = 0.2% , and NOx = 1,450 ppm (limit: 200 ppm ). Earlier pre-catalyst testing showed CO = 0.5% , O2 = 0.5% , HC = 85 ppm , CO2 = 14.1% , and NOx = 1,480 ppm .
Analysis: Because CO ( 0.03% ) and HC ( 18 ppm ) are near zero and CO2 is at a peak 15.1% , the readings suggest effective oxidation; verify lambda using the analyzer rather than deriving it from CO2 alone and the catalytic converter's oxidation bed ( Pt / Pd ) is working properly. However, pre-catalyst NOx is already excessive ( 1,480 ppm ) and virtually no NOx reduction occurs across the catalyst.
Root Cause & Fix: Testing the DPFE EGR system reveals a corroded DPFE transducer holding 0.2 V with a plugged steel orifice tube preventing EGR flow ( peak combustion temperatures >2,500°F ), combined with thermal aging of the front rhodium ( Rh ) reduction bed. Repairing the DPFE EGR circuit drops pre-catalyst NOx to 420 ppm , and replacing the degraded TWC brings tailpipe NOx down to 35 ppm .