Study guide
10.6 EVAP Monitors and Leak-Test Procedures
ASE T1 — Gasoline Engines Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & ASE T1 Exam Overview
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy
2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust
2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds
3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing
3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing
4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools
4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service
5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair
5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service
6 Chapter 5: Engine Block Diagnosis and Repair
6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection
7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair
7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators
8 Chapter 7: Ignition System Diagnosis and Repair
8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning
9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair
9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service
10 Chapter 9: Emissions Control Systems Diagnosis and Repair
10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures
11 Chapter 10: Computerized Engine Controls Diagnosis and Repair
11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation
10.6 EVAP Monitors and Leak-Test Procedures
Key Takeaways Explain This Topic AI
Vacuum-decay and engine-off natural-vacuum tests are examples; other monitor designs exist.
Leak-code thresholds depend on calibration rather than a universal P0455 hole size.
Use the approved smoke pressure and valve command before interpreting flow or decay.
Last updated: October 2026
Note
EVAP Monitors and Leak-Test Procedures uses stated teaching examples. Actual pin assignments, dimensions, thresholds and procedures must come from the identified engine, component and diagnostic tool.
- OBD-II EVAP Leak Monitors, DTCs & Low-Pressure Smoke Testing (Tasks G.11, G.12)
- EVAP Monitor Enable Criteria & Operating Modes ( Mode \$06 )
Before the PCM runs its OBD-II EVAP leak monitor, strict entry conditions must be satisfied:
Fuel Tank Level: Must be between 15% and 85% ( ~1/8 to 7/8 tank ). Below 15% , fuel slosh and large vapor volume skew decay rates; above 85% , liquid fuel is too close to the vapor dome.
Cold Soak / Temperature Window: Requires a verified cold start where ECT and IAT are within 10°F ( 5.5°C ) of each other, ambient temperature is between 40°F and 95°F ( 4°C–35°C ) , and barometric pressure is >75 kPa (altitude <8,000 ft ).
The following are two common OBD-II EVAP leak-detection strategies; other designs use leak-detection pumps or natural-vacuum switches:
Engine-Running Vacuum-Decay Monitor: The PCM commands the Normally Open vent solenoid CLOSED , pulses the Normally Closed purge solenoid OPEN until the FTP sensor registers a calibrated light vacuum ( ~8 to 12 in. H2O ), commands the purge valve CLOSED to seal the system, and measures the rate at which FTP vacuum decays over 15 to 30 seconds .
Engine-Off Natural Vacuum ( EONV ) Monitor: Used on late-model GM and Ford medium-duty trucks to test down to a 0.020 in. ( 0.5 mm ) orifice standard after key-off. Following a warm drive cycle, the PCM wakes up after shutdown, closes the EVAP vent valve, and monitors the FTP sensor as the sealed fuel and vapor naturally warm (building slight positive pressure) and then cool (creating natural vacuum) without any fuel slosh.
EVAP Diagnostic Trouble Code Leak / Fault Size Equivalent FTP Sensor & Monitor Behavior Most Common Commercial Truck Root Causes
P0455 — EVAP Gross / Large Leak large-leak or inability-to-seal criterion defined by the calibration; no universal 0.090-inch P0455 boundary Vacuum fails to pull down during purge phase, or zero pressure change occurs during EONV . Loose, cross-threaded, or missing fuel filler cap; disconnected EVAP hose; split filler neck hose; EVAP vent valve mechanically stuck open .
P0442 — EVAP Small Leak 0.040 in. ( 1.0 mm ) calibrated orifice Target vacuum ( ~10 in. H2O ) is reached, but FTP vacuum decays faster than the 0.040 in. threshold. Weathered/cracked fuel cap O-ring; corroded steel fuel pump lock ring on top of tank; cracked canister seam; chafed nylon vapor tube.
P0456 — EVAP Very Small Leak 0.020 in. ( 0.5 mm ) calibrated orifice Vacuum decays slightly above the 0.020 in. threshold or fails EONV phase. Pin-hole corrosion in metal filler neck or tank sender flange; weeping Schrader service port valve core; micro-crack in purge/vent O-ring.
P0446 — EVAP Vent Performance Restricted vent path or stuck-closed vent valve FTP sensor pulls excessive deep vacuum ( >-15 in. H2O ) during normal purging when vent is commanded open. Mud/spider nest plugging fresh-air vent filter box; pinched vent hose; vent valve mechanically seized closed; loose charcoal pellets.
P0449 — EVAP Vent Solenoid Circuit Electrical open / short in vent solenoid circuit PCM driver fault detection flags open or shorted circuit on frame-mounted vent coil ( normal: 18–35 Ω ). Road salt/water corrosion inside the 2-pin frame-rail vent solenoid connector; broken power ( B+ ) or PCM control wire; open solenoid coil.
P0496 — EVAP High Purge Flow Purge flow detected during non-purge state FTP sensor sees tank vacuum increase while purge command is 0% and vent valve is closed. EVAP canister purge solenoid valve mechanically stuck open (often jammed by carbon granules or failed internal seat).
Tip
Low-Pressure ( <1 psi ) Nitrogen/Smoke Testing & Half-Splitting 0.020 in. Leaks: Never apply unregulated shop air to an EVAP system—excess pressure can damage the FTP sensor diaphragm and rupture the charcoal canister! Connect an EVAP-approved nitrogen/smoke machine (regulated internally to 0.5 psi / 14 in. H2O ) to the EVAP service port (removing the specified service-port core, if required by the tool procedure) or purge line. Use a scan tool bidirectional control to command the EVAP Vent Solenoid CLOSED ( SEALED ) . Watch the smoke machine flowmeter ball : if the ball drops to zero, the system is sealed; if it hovers at the 0.020 in. mark, clamp the vapor line just ahead of the charcoal canister with smooth-jaw hose pliers to instantly isolate whether the leak is in the engine bay purge line or back at the canister/tank/filler neck.
Worked Example: Diagnostic Scenario: Class 4 Box Truck with Hard Start After Refueling & P0496
Concern: A delivery driver reports that a Class 4 box truck cranks for 8 to 10 seconds and stumbles roughly every time it is restarted immediately after filling the fuel tank, accompanied by DTCs P0496 (EVAP System Flow During Non-Purge) and P0172 (System Too Rich Bank 1) .
Scan Tool & Bay Testing: At warm curb idle, the scan tool shows EVAP Purge Command at 0% , yet STFT Bank 1 is at -16% and the FTP sensor reads -11.5 in. H2O (vacuum) when the technician momentarily commands the EVAP Vent Valve closed. Unplugging the 2-wire electrical connector and removing the canister-side vapor hose from the intake-mounted EVAP purge solenoid reveals strong, continuous manifold vacuum ( 18 in. Hg ) sucking straight through the de-energized purge valve.
Root Cause & Fix: Tapping the removed purge solenoid onto a clean shop towel shakes loose several hard black activated-charcoal pellets that had migrated from a ruptured charcoal canister baffle and wedged the NC purge pintle open. The technician replaces both the ruptured charcoal canister and the contaminated EVAP purge solenoid, services the isolated vapor lines by the approved cleaning or replacement method, and verifies that the new purge valve holds 15 in. Hg vacuum with 0.0 in. H2O tank pressure at idle.
Applied Diagnostic Check
An EVAP flowmeter reports flow under the tool's test pressure and setup. Its calibrated hole-size mark is an equivalent leak reference, not a measurement of a crack's physical width. A long crack, several small paths and a round reference hole can produce similar flow. Use smoke location or section isolation to find the actual defect. If no smoke appears, inspect the tool connections and valve state before increasing pressure. A seal can open only under a particular temperature or vacuum condition; follow the specified alternate test rather than declaring the system good from one static observation.
Testing the Canister and Vapor Lines Without Creating a New Fault
Inspect the fuel cap seal and filler neck, canister case, vapor tubes, connectors and vent filter before applying smoke. Check that the tool connection itself is sealed. A leak at an adapter can look like a tank fault, and a vent valve left open can produce heavy flow without any broken pipe. Command and verify the required valve state, then compare the flow reading with the tool's calibrated leak standard.
Isolate sections only using fittings or flexible sections the manufacturer permits. Do not pinch hard nylon lines or pressurize the system with unregulated shop air. If a damaged canister has released charcoal into a valve, inspect the affected line and follow the cleaning or replacement instructions. After reassembly, repeat the seal test and verify purge and vent operation. Monitor completion is an additional verification step, not a substitute for checking that the replaced components were installed without leaks.