Study guide
10.5 EVAP Flow, Purge and Refueling Faults
ASE T1 — Gasoline Engines Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & ASE T1 Exam Overview
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy
2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust
2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds
3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing
3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing
4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools
4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service
5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair
5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service
6 Chapter 5: Engine Block Diagnosis and Repair
6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection
7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair
7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators
8 Chapter 7: Ignition System Diagnosis and Repair
8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning
9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair
9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service
10 Chapter 9: Emissions Control Systems Diagnosis and Repair
10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures
11 Chapter 10: Computerized Engine Controls Diagnosis and Repair
11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation
10.5 EVAP Flow, Purge and Refueling Faults
Key Takeaways Explain This Topic AI
On the example design, purge is normally closed and vent is normally open.
A leaking purge valve can admit vapor or air when no purge is commanded.
A blocked vent path can cause repeated nozzle shutoff and excessive purge vacuum.
Last updated: October 2026
Note
EVAP valve arrangements, monitor enabling conditions and leak-test sizes in this lesson are teaching examples, not a service specification for every T1 truck. Use the identified engine, component and tool manufacturer's procedure and limits when making a repair decision.
- 10.3 Evaporative Emissions Control (EVAP) Systems, Leak Testing & DTCs
- Commercial Truck EVAP Architecture & Component Normal States (Tasks G.10, G.11)
Medium- and heavy-duty gasoline trucks carry large 35 to 65+ gallon fuel tanks mounted along chassis frame rails, often exposed to high exhaust radiant heat and wide ambient temperature swings. Liquid gasoline evaporates continuously inside the tank, generating volatile Hydrocarbon ( HC ) vapors. The Evaporative Emissions Control ( EVAP ) and Onboard Refueling Vapor Recovery ( ORVR ) systems capture and store these fuel vapors in activated carbon canisters and meter them into the engine during warm closed-loop operation to reduce fuel-vapor emissions.
Mastering EVAP diagnostics starts with knowing the de-energized (normal) mechanical state of every valve and sensor:
Activated Carbon / Charcoal Canister(s): Large ( 1.5 to 3.5+ liter ) nylon housings filled with porous activated charcoal granules that adsorb and hold HC fuel vapors displaced from the fuel tank during hot soak and refueling.
EVAP Canister Purge Solenoid Valve ( Normally Closed [NC] ): Mounted on the engine or intake manifold between the charcoal canister purge line and intake manifold vacuum. When de-energized (key off, engine cranking, cold operation on this example strategy), an internal spring holds the purge valve hermetically closed ( NC ) . During warm closed-loop off-idle driving, the PCM commands the purge valve open via a pulse-width-modulated ( PWM , 0% to 100% duty cycle) ground signal, drawing stored vapors into the intake plenum while watching STFT / LTFT to adjust injector pulse width for the rich purge vapor.
EVAP Canister Vent Solenoid Valve ( Normally Open [NO] ): Mounted near the charcoal canister on the truck frame rail, connected to a remote fresh-air inlet filter box. When de-energized, its spring holds the valve wide open ( NO ) for two critical reasons:
During active engine purging, fresh filtered atmospheric air must enter through the open vent valve to sweep across the charcoal bed and carry released HC vapors into the engine.
During fuel station refueling, large volumes of air displaced by incoming liquid gasoline must pass through the charcoal bed (which strips out the HC molecules) and exit freely to the atmosphere through the open vent valve.
When Is the Vent Valve Closed? The PCM energizes ( 12 V / ground control) the vent solenoid CLOSED ( SEALED ) only during an active OBD-II EVAP leak test or when commanded closed by a technician's scan tool during smoke testing .
3-Wire Fuel Tank Pressure ( FTP ) Transducer: Mounted on the fuel pump module flange or vapor line, the FTP sensor receives a 5.0 V reference and low-reference ground from the PCM and returns a linear signal voltage centered around ~1.5 V to 2.5 V at atmospheric pressure ( 0.0 in. H2O / 0 Pa ) . Positive tank pressure increases FTP voltage (or decreases it on inverted-scale systems), while negative tank vacuum pulls FTP voltage in the opposite direction, measuring slight pressures down to fractions of an inch of water column ( in. H2O ).
Liquid-Vapor Separator & Rollover / Fill-Limit Vent Valves ( FLVV ): Float-actuated valves inside the top of the fuel tank that pass vapor while blocking liquid fuel from entering the charcoal canister on steep grades, sharp turns, or vehicle rollovers.
- Driveability & Refueling Problems Caused by EVAP Failures (Task G.10)
- 1. Stuck-Open EVAP Canister Purge Solenoid Valve ( P0496 , P0172 / P0175 , P0171 / P0174 )
Classic Symptom — Hard Start / Extended Crank Immediately After Refueling: When a driver pumps 45 gallons of liquid gasoline into a commercial truck tank, 45 gallons of dense fuel vapor are pushed out of the tank into the charcoal canister. In a healthy system, the Normally Closed ( NC ) purge valve blocks those vapors from reaching the engine while parked at the pump. However, if the purge valve pintle is mechanically stuck open (often jammed by a tiny granule of loose charcoal or debris), pressurized refueling vapor rushes straight up the purge hose and floods the intake manifold plenum with raw fuel vapor . When the driver turns the key after hanging up the fuel nozzle, the engine cranks for several seconds before coughing to life in a severely flooded, rich condition ( P0172 / P0175 ).
Secondary Symptoms ( P0496 and Lean Idle Codes P0171 / P0174 ): Once the stored fuel vapor in the canister is depleted during driving, a stuck-open purge valve continuously pulls fresh atmospheric air through the open vent valve and canister into the intake manifold, acting as a vacuum leak at curb idle ( rough idle, +12% to +20% fuel trims ). Furthermore, when the PCM runs its non-purge flow check (commanding 0% purge while closing the vent valve), intake vacuum rapidly pulls negative pressure in the fuel tank even though purge is commanded OFF, setting P0496 (EVAP System High Purge Flow / Flow During Non-Purge) .
Hands-On Verification: Unplug the purge solenoid electrical connector and disconnect the canister-side hose at warm curb idle. Touch a finger or connect a vacuum gauge to the purge valve inlet port: a healthy NC valve must have zero suction ( 0 in. Hg ) . With the engine off, apply 15 in. Hg with a hand vacuum pump to the de-energized purge valve; if vacuum bleeds down at all, replace the purge valve (and inspect the hose for black charcoal pellets!).
2. Stuck-Closed EVAP Vent Valve, Plugged Vent Filter, or Ruptured Charcoal Canister ( P0446 / P0449 )
Classic Symptom — Gas Station Nozzle Clicks Off Repeatedly / Slow Refueling: Commercial fuel dispensers pump gasoline at 8 to 10 gallons per minute . For liquid fuel to enter the tank at that speed, an equal volume of displaced air/vapor must escape through the ORVR tube, charcoal canister, and open ( NO ) EVAP vent valve . If the vent valve is mechanically seized closed, the remote fresh-air vent filter/hose is plugged by mud, undercoating, or spider/mud-dauber nests , or a ruptured canister baffle has dumped loose charcoal pellets into the vapor lines, pressure builds inside the tank within two seconds, forcing fuel backup up the filler neck and tripping the gas station nozzle automatic shutoff repeatedly .
Excessive Tank Vacuum During Purge ( P0446 ): When the PCM opens the purge valve during highway cruising while the vent path is plugged or stuck closed, intake manifold vacuum cannot draw replacement air through the vent filter. Instead, it pulls a deep, abnormal vacuum ( >-15 to -25 in. H2O ) inside the fuel tank—capable of sucking plastic fuel tanks inward and damaging the internal fuel pump module—while the FTP sensor sets P0446 (EVAP Emission Control System Vent Control Circuit Performance / Restricted Vent) .
Warning
Never Top Off the Fuel Tank & Always Inspect for Loose Charcoal Pellets: Repeatedly clicking the fuel nozzle after automatic shutoff forces liquid gasoline past the fill-limit valve directly into the charcoal canister. Liquid fuel saturates the carbon bed, disintegrates the internal foam/fiberglass retention baffles, and releases hard black charcoal granules into the nylon EVAP lines. If a technician finds black carbon granules inside a stuck-open purge valve ( P0496 ) or stuck vent valve ( P0446 ), simply replacing the valve will result in an immediate repeat failure unless the ruptured charcoal canister is replaced and all vapor lines are serviced while isolated using the manufacturer's approved method.