Study guide
6.5 Crankshaft Inspection and Bearing Wear Evidence
ASE T1 — Gasoline Engines Medium/Heavy Truck
Track your progress as you read
Finished sections get a check mark.
1 Introduction & ASE T1 Exam Overview
1.1 ASE T1 Exam Format, Scoring, Fees & Certification Requirements 1.2 Class 4–8 Gasoline & LPG Truck Engines and ASE Question Strategy
2 Chapter 1: General Engine Diagnosis — Complaints, Leaks, Noises & Exhaust
2.1 Concern Verification and Service Information 2.2 Fluid Leak Isolation and Gauge Verification 2.3 Lower-End Noise and Cylinder Cut-Out Evidence 2.4 Valvetrain, Accessory and Vibration Diagnosis 2.5 Oil Consumption and Blue Exhaust Smoke 2.6 Coolant Vapor, Rich Mixture and Exhaust Sounds
3 Chapter 2: General Engine Diagnosis — Vacuum, Balance, Compression & Leak-Down Testing
3.1 Vacuum Principles and Controlled Dynamic Tests 3.2 Vacuum Patterns and Manifold Pressure Diagnosis 3.3 Cylinder Power Balance and Contribution Testing 3.4 Dry, Wet and Running Compression 3.5 Cylinder Leakage (Leak-Down) and Combustion-Leak Block Testing
4 Chapter 3: General Engine Diagnosis — Electrical, Starting, Charging & Lab Tools
4.1 DMM, Scope and Scan-Tool Evidence 4.2 Harness, Connector and Schematic Diagnosis 4.3 Battery Condition, Parasitic Draw & Starting System Diagnosis 4.4 Charging System Performance, Voltage Drop & Belt Drive Service
5 Chapter 4: Cylinder Head & Valve Train Diagnosis and Repair
5.1 Head Disassembly, Cracks, Threads and Plugs 5.2 Head Metrology and Gasket Installation 5.3 Valve and Guide Inspection 5.4 Valve Seats, Springs and Stem Seals 5.5 Pushrods, Rockers and Valve-Train Harnesses 5.6 Lifter Preload, Valve Lash and OHC Service
6 Chapter 5: Engine Block Diagnosis and Repair
6.1 Pans, Covers, Seals and Sealants 6.2 Block Inspection and Cylinder Bore Metrology 6.3 Cam Bearings, Lobe Lift and Endplay 6.4 In-Block Lifters and Timing Drive 6.5 Crankshaft Inspection and Bearing Wear Evidence 6.6 Bearing Fit, Clearance and Crankshaft Endplay 6.7 Pistons, Ring Fits and Installation 6.8 Rods, Vibration Damper and Flywheel Inspection
7 Chapter 6: Lubrication & Cooling Systems Diagnosis and Repair
7.1 Oil Pressure and Lubrication Fault Diagnosis 7.2 Oil Pump, Cooler and Oil/Filter Service 7.3 Overheating, Overcooling and Thermostats 7.4 Coolant Testing and Water Pump Service 7.5 Radiators, Caps and Recovery Systems 7.6 Fans, Belts and Warning Indicators
8 Chapter 7: Ignition System Diagnosis and Repair
8.1 Ignition Symptoms and Combustion Knock 8.2 Ignition DTCs and Misfire Data 8.3 Primary Ignition Circuits and Coil Testing 8.4 Spark Plugs and Secondary Waveforms 8.5 CKP/CMP Sensor and Correlation Tests 8.6 Ignition Modules and Profile Learning
9 Chapter 8: Fuel, Air Induction & Exhaust Systems Diagnosis and Repair
9.1 Fuel Trim and Driveability Diagnosis 9.2 Fuel Tanks, Lines and Fuel Quality 9.3 Fuel Pump Circuits and Current Waveforms 9.4 Fuel Pressure, Volume and LPG Applications 9.5 Injector and Fuel Rail Testing 9.6 Electronic Throttle Testing and Learning 9.7 Air Filtration and Intake Leak Diagnosis 9.8 Exhaust Leaks and Restriction Testing 9.9 Gasoline Direct Injection Diagnosis and Service
10 Chapter 9: Emissions Control Systems Diagnosis and Repair
10.1 PCV Flow and Crankcase Pressure 10.2 EGR Flow, Feedback and Service 10.3 Secondary AIR Operation and Diagnosis 10.4 Catalyst Oxygen Storage and Five-Gas Analysis 10.5 EVAP Flow, Purge and Refueling Faults 10.6 EVAP Monitors and Leak-Test Procedures
11 Chapter 10: Computerized Engine Controls Diagnosis and Repair
11.1 DTC States and MIL Operation 11.2 Readiness, Freeze Frame and Repair Verification 11.3 Service Literature and Diagnosis with DTCs 11.4 No-DTC Driveability Diagnosis 11.5 Sensor Circuits and Shared References 11.6 Actuator and Low-Side Driver Testing 11.7 PCM Power Feeds and Loaded Grounds 11.8 PCM Programming and Network Diagnosis 11.9 Scan Data and Freeze-Frame Interpretation
6.5 Crankshaft Inspection and Bearing Wear Evidence
Key Takeaways Explain This Topic AI
Brush drilled crank oil passages so loosened contamination cannot reach new bearings.
Journal taper compares diameters along one axis at opposite edges.
Diagonal rod-bearing and piston wear justifies a rod-alignment check.
Last updated: October 2026
Note
Journal sizes, bearing grading and thrust-clearance limits in this lesson are teaching examples, not a service specification for every T1 truck. Use the identified engine, component and tool manufacturer's procedure and limits when making a repair decision.
Crankshaft Inspection, Bearing Failure Analysis, Select-Fit & Clearances
In a medium- or heavy-duty gasoline truck engine, the crankshaft and its hydrodynamic plain bearings must support tens of thousands of pounds of combustion force without metal-to-metal contact, supported by a hydrodynamic film generated by journal motion, with pressurized supply replenishing the oil; diametral clearance is not the same as loaded film thickness. Rebuilding a durable lower end requires meticulous crankshaft journal metrology, forensic diagnosis of old bearing wear patterns, and exact control of bearing crush, oil clearance, and thrust endplay.
- Crankshaft Inspection & Journal Metrology (Task C.6)
- Cleaning Oil Passages, Crack Inspection & Fillet Radii
Drilled Oil Passage Brushing : During engine operation, centrifugal force inside the spinning crankshaft throws heavy metallic particles and carbon sludge outward against the walls of the diagonal oil passages drilled between the main journals and rod journals. Chemical washing softens this packed centrifugal sludge deposit; if a technician fails to run a stiff nylon rifle brush with solvent through every crankshaft oil hole , that loosened plug of grit flushes straight into the new connecting rod bearings on the very first startup.
Crack & Surface Inspection : Inspect all main and connecting rod journals for deep circumferential grooves, ridging, babbitt transfer, or thermal bluing from oil starvation. Perform wet fluorescent magnetic particle inspection (Magnaflux) across the entire crankshaft, paying close attention to the oil hole edges and the transition zones between journals and counterweights.
Journal Fillet Radii : Where each horizontal main or rod journal meets the vertical crankshaft cheek/counterweight, the transition is machined with a precision curved fillet radius (often deep-rolled or induction-hardened on heavy-duty truck crankshafts) to distribute bending and torsional loads. If a crankshaft grinder dresses the grinding wheel with too sharp a corner, a severe stress riser is created and the crankshaft will snap across the web under heavy towing loads; conversely, if the fillet radius is left too large, the outer edges of the bearing shell ride up on the radius ( fillet ride ), pinching off oil flow and wiping the edges of the bearing.
Four-Point Crankshaft Journal Measurement
Using an outside micrometer calibrated to 0.0001 in. , measure every main journal and connecting rod journal at four points : vertically ( Axis A , parallel to crank throw) and horizontally ( Axis B , 90° to crank throw) near both the front/left edge and the rear/right edge of the journal:
Journal Out-of-Round = |Vertical Diameter (A) - Horizontal Diameter (B)| at the same side of the journal ( typical service limit: 0.0005 to 0.0010 in. / 0.013 to 0.025 mm ). Rod journals wear out-of-round faster than main journals because peak combustion load always hammers the top of the rod journal at the exact same rotational angle.
Journal Taper = |Front/Left Diameter - Rear/Right Diameter| along the same axis ( typical service limit: 0.0005 to 0.0010 in. ).
Piston, Rod-Bearing & Main-Bearing Wear Pattern Failure Analysis (Task C.7)
Never discard old main and rod bearing shells without reading their wear patterns first. The location of babbitt overlay wear pinpoints hidden geometric distortion in the connecting rods, crankshaft, or block main tunnel:
Bearing / Piston Wear Pattern Observed Underlying Geometric or Mechanical Root Cause Required Corrective Action
Diagonal / Opposite-Edge Wear (upper shell worn at front-left edge, lower shell worn at rear-right edge) + Diagonal Piston Skirt Scuffing Bent or twisted connecting rod ( rod alignment fault) cocking the bearing shell on the journal and tilting the piston in the bore Check rod on a connecting rod alignment fixture; replace the damaged rod unless the manufacturer expressly permits reconditioning
Worn Along One Outer Edge on Both Shells (uniform heavy wear around one side edge only) Tapered crankshaft journal OR excessive journal fillet radius ( fillet ride ) Grind crankshaft journal straight with correct fillet radius and install undersize bearings
Heavy Wear Band Concentrated in Exact Center of Shell Crowned (barrel-shaped) journal (conversely, wear on both outer edges simultaneously indicates an hourglass journal ) Regrind crankshaft journals parallel and flat across their full width
Worn Heavily at Parting Lines ( 3 o'clock & 9 o'clock ) while crown ( 12 & 6 o'clock ) looks light Out-of-round ("pinched") big-end rod bore or main bore caused by cap distortion, over-torquing, or filing the cap Recondition (resize/hone) the connecting rod big-end housing bore or align-hone the main bearing tunnel
Uneven Progressive Wear Across Adjacent Main Bearings (e.g., #2 and #4 mains wiped heavily on one side while #1 and #5 are light) Misaligned / warped main bearing tunnel in the cylinder block OR a bent crankshaft Check bare block main tunnel with precision straightedge/arbor bar ( limit 0.001 in. ) and align-bore / align-hone block
Craters / Flaking Babbitt Chunks Missing down to copper/aluminum lining Bearing fatigue from detonation, pre-ignition, or sustained low-RPM lugging under heavy truck load Correct ignition/fueling detonation causes and replace bearings
Applied Diagnostic Check
Keep the main caps in their original locations and orientation during housing checks. The block and caps were machined as an assembly; a cap that bolts down can still create an incorrect bore. Record any fretting at the mating surfaces and verify the specified bolt condition before torque. Where the bearing pattern suggests a distorted bore, measure with the inserts removed and the cap assembled according to the procedure. Journal dimensions and housing dimensions are complementary evidence. Neither an attractive wear pattern nor a selected bearing color proves that the assembled support line and clearance are correct.
Accepting the Repaired Journal
Check the finished journal at multiple positions and verify surface finish, oil-hole edges and fillet geometry. A correct nominal diameter does not prove the journal is round, parallel or compatible with the selected shell. The repair record should identify the final undersize, bearing part and actual installed clearance. Reinspect any unusual contact pattern during trial assembly rather than relying on a machining-size label alone.
Making Journal Measurements Repeatable
Clean the journal and micrometer faces, verify instrument zero and allow the part to reach the required measuring temperature. Measure away from an oil hole or obvious damage, then record the same axial positions and rotational axes on each journal. A single measurement cannot show taper or ovality. For example, two diameters of 2.1000 and 2.0994 inches at the same axial position differ by 0.0006 inch; the decision still depends on the supplied journal tolerance and allowed repair.
Wear patterns narrow the investigation rather than substituting for geometry. Check the rod big-end bore with the cap matched and torqued as specified, and inspect its small-end bushing and pin condition. Check the main housing line if several bearings show related edge loading. Do not use a thicker shell to hide a distorted housing. A ground journal also needs the required surface finish and fillet geometry, with a bearing that clears the fillet. Record the final dimensions and selected repair size so the clearance check can be interpreted correctly.